Honeywell Accenta 8 User Manual

							Accenta/Optima Engineer’s Manual
47
Appendix 1 - Event Log Messages
Event Log
Table 4. Event Log
KEYPAD TEXT DESCRIPTION
Zone events
INTRUDER Intruder zone activated (opened)
ENTRY START Entry time started
ZONE OMITTED Zone has been omitted for one set period
FIRE ZONE Fire zone activated (opened)
ZONE EXCLUDED Zone has been omitted for one set period
User Events
CODE ENTRY User has entered code
SET PROGRAM User has set the system with program 1, 2 or 3
SYSTEM UNSET User has unset the system
System Events
CLEAR LOG Event log has been cleared
NV M INIT Panel was set to factory default condi ti ons
START UP Panel was cold started
PA PA zo ne  acti vate d
RK P  PA Remote K eypad PA enabled
DURESS CODE Duress code used to set or unset the system
ENTRY TIMEOUT Ti meout alarm after entry ti me has expi red
SYSTEM REARM System rearmed after an alarm
CODE TAMPER Invalid user code was entered
USER RESET User has reset the system
ENGR RES E T Engi neer has reset the system
ENG ACCESS Entering engineer program mode
ENG FINISH Leaving engineer program mode
OLD  TIME Old ti me i ndi cated before change
NEW TIME New ti me i ndi cated after change
OLD  D ATE Old date i ndi cated before change
NEW DATE New date indicated after change
MAINS FAIL Mains power supply failure
MAINS OK Mains power supply restored
LOOP TAMPER Tamper alarm indicated 
						

							Accenta/Optima Engineer’s Manual
48 
						

							Accenta/Optima Engineer’s Manual
49
Appendix 2 - Library
Attic
Back Door
Basement
Bathroom
Bedroom 1
Bedroom 2
Bedroom 3
Conservatory
Dining Room
Fire Zone
Front Door
Garage
Hall
Library
Kitchen
Landing
Living Room
Lounge
Patio
Porch
Stairs
Study
Utility Room
Window 1
Window 2
Window 3 
						

							Accenta/Optima Engineer’s Manual
50 
						

							Accenta/Optima Engineer’s Manual
51
Servicing Organisation Details
Servicing Organisation name:
Telephone number:
Date of Installation:
Account Number:
Parts
8SP399AAccenta mini panel with LCD keypad
8SP400AAccenta mini panel with LED keypad
8EP396AOptima compact panel
8SP419AAccenta panel metal enclosure with LCD keypad
8SP420AAccenta panel metal enclosure with LED keypad
8EP417A Accenta LCD remote keypad
8EP416 Accenta LED remote keypad
8EP276Informa
8EP289Extension speaker
IS215T 12 meter PIR
Servicing/Parts
Resistance(Ω) Are a  pro te c tio n a nd e quipme nt us e d (e g  PIR ,  Co nta c ts )
Zo ne  1
Zo ne  2
Zo ne  3
Zo ne  4
Zo ne  5
Zo ne  6
Zo ne  7
Zo ne  8
Table 5. Zones and Resistance 
						

							Accenta/Optima Engineer’s Manual
52 Honeywell Security (UK 64)
Newhouse Industrial Estate
Motherwell
Lanarkshire
ML1 5SB
UK
© Copyright Honeywell Security IE1-0040  Rev 1.0
Engineer Program Mode [PROG] [9] [9] [9] [9].  To exit Engineer Program Mode [RESET]
0 = Walk Test
1 = Alarm Test1 = Bell
2 = Strobe
3 = Sounder
2 = Test Outputs1 = Fire
2 = PA
3 = Intruder
4 = Set
5 = Abort
3 = Set up System FlagsFlag 11 = Silent PA
2 = RKP PA
3 = Engineer Reset
4 = PA User Reset
5 = Fire User Reset
6 = Bells in Fire
7 = Zone 7 Fire
8 = Zone 8 Fire
Flag 2
1 = Single Key Set
2 = Strobe On Set
Flag 3
System and Software
Version
4 = Set Up Time and Date
6 = Set Up Zone Names
7 = Set Up Timers
1 = Bell Time00 - 99 minutes
2 = Bell Delay
00 - 99 minutes
3 = Rearm Count
0 = No rearms
1 - 8 = number of rearms
9 = Always rearm
8 = Set Up Codes1 = User 1 (Manager)
2 = User 2 (deletable)
3 = Duress (deletable)
4 = Engineer
4-digit code
C = View Event Log
1 = LCD
2 = LED
O = Omit Allow &
       Double Knock
1 = Double Knock
2 = Omit Allow
P = Set Up Programs
      (1, 2 or 3)1 = Used Zones (1-8) 
2 = Timed Zones
3 = Inhibit Zones
4 = Entry Time (00-99 seconds)
5 = Exit  Time (00-99 seconds)
6 = Exit Mode