Honeywell Accenta 8 User Manual
Have a look at the manual Honeywell Accenta 8 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 178 Honeywell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 26
Accenta/Optima Engineer’s Manual
22
System Flags
Flag 1 - Options
There are eight options under Flag1 which are described below:
1 = Silent PA
When this flag is set to ON, operating PA will cause a silent PA alarm. Pressing the [1] button toggles the flag
ON or OFF.
2 = RKP PA
When this flag is set to ON, the keypad PA buttons are enabled. Pressing the [2] button toggles the flag ON
or OFF.
3 = Engineer Reset
When this flag is set to ON, an engineer code must be entered to reset the system after Tamper,...](http://img.usermanuals.tech/thumb/35/62752/w64_honeywell-accenta-8-user-manual-1491295022_d-25.png "Page 26
Accenta/Optima Engineer’s Manual
22
System Flags
Flag 1 - Options
There are eight options under Flag1 which are described below:
1 = Silent PA
When this flag is set to ON, operating PA will cause a silent PA alarm. Pressing the [1] button toggles the flag
ON or OFF.
2 = RKP PA
When this flag is set to ON, the keypad PA buttons are enabled. Pressing the [2] button toggles the flag ON
or OFF.
3 = Engineer Reset
When this flag is set to ON, an engineer code must be entered to reset the system after Tamper,...")
![Page 27
Accenta/Optima Engineer’s Manual
23
Flag 2
NOTE:Pressing the [9] button sets all flags ON. Pressing the [0] button sets all flags OFF. Pressing the
[RESET] button leaves the function.
Accenta Optima Accenta OptimaAccenta Optima Accenta Optima
Accenta Optima
Version 1.00 Version 1.00Version 1.00 Version 1.00
Version 1.00F130-01-101 F130-01-101F130-01-101 F130-01-101
F130-01-101Build 101 (01)R Build 101 (01)RBuild 101 (01)R Build 101 (01)R
Build 101 (01)R
Date May 05 2006 Date May 05 2006Date May 05 2006...](http://img.usermanuals.tech/thumb/35/62752/w64_honeywell-accenta-8-user-manual-1491295022_d-26.png "Page 27
Accenta/Optima Engineer’s Manual
23
Flag 2
NOTE:Pressing the [9] button sets all flags ON. Pressing the [0] button sets all flags OFF. Pressing the
[RESET] button leaves the function.
Accenta Optima Accenta OptimaAccenta Optima Accenta Optima
Accenta Optima
Version 1.00 Version 1.00Version 1.00 Version 1.00
Version 1.00F130-01-101 F130-01-101F130-01-101 F130-01-101
F130-01-101Build 101 (01)R Build 101 (01)RBuild 101 (01)R Build 101 (01)R
Build 101 (01)R
Date May 05 2006 Date May 05 2006Date May 05 2006...")
![Page 28
Accenta/Optima Engineer’s Manual
24
6 = Set Up Zone Names
This option allows each of the eight zones to be given a name from the library (Appendix 2).
4 = Set Up Time and Date
LCD Keypad:
This option allows the Time or Date to be modified. Pushing button [4] selects the option and the first screen
appears as typically below:
Time and Date Time and DateTime and Date Time and Date
Time and Date
Time? Time? Time? Time?
Time?
1 11 1
1
3:46:17 3:46:173:46:17 3:46:17
3:46:17 The Time can be modified in...](http://img.usermanuals.tech/thumb/35/62752/w64_honeywell-accenta-8-user-manual-1491295022_d-27.png "Page 28
Accenta/Optima Engineer’s Manual
24
6 = Set Up Zone Names
This option allows each of the eight zones to be given a name from the library (Appendix 2).
4 = Set Up Time and Date
LCD Keypad:
This option allows the Time or Date to be modified. Pushing button [4] selects the option and the first screen
appears as typically below:
Time and Date Time and DateTime and Date Time and Date
Time and Date
Time? Time? Time? Time?
Time?
1 11 1
1
3:46:17 3:46:173:46:17 3:46:17
3:46:17 The Time can be modified in...")
![Page 29
Accenta/Optima Engineer’s Manual
25
Timers
LCD keypad:
To change the Bell Time from 15 to 20 minutes:
•Press [up arrow] for menu Set Up Timers.
•Press [7] or [SET] for option 71 Set up Bell Time.
•Press [1] or [SET]. The Bell Time in minutes is displayed.
• The cursor is under the first digit. Select [2].
• The cursor moves to the second digit. Select [0].
• To accept the change press [SET] then [RESET]
OR to cancel the change press the [RESET] button twice.
7 = Set Up Timers
This option allows the Bell...](http://img.usermanuals.tech/thumb/35/62752/w64_honeywell-accenta-8-user-manual-1491295022_d-28.png "Page 29
Accenta/Optima Engineer’s Manual
25
Timers
LCD keypad:
To change the Bell Time from 15 to 20 minutes:
•Press [up arrow] for menu Set Up Timers.
•Press [7] or [SET] for option 71 Set up Bell Time.
•Press [1] or [SET]. The Bell Time in minutes is displayed.
• The cursor is under the first digit. Select [2].
• The cursor moves to the second digit. Select [0].
• To accept the change press [SET] then [RESET]
OR to cancel the change press the [RESET] button twice.
7 = Set Up Timers
This option allows the Bell...")
![Page 30
Accenta/Optima Engineer’s Manual
26
Timers (cont’d)
LCD keypad:
To change the Bell Delay time from 00 to 12 minutes:
•Press [up arrow] for menu Set Up Timers.
•Press [7]or [SET]. Option 1 Set up Bell Time appears.
•Press [2]. The Bell Delay time in minutes is displayed.
• The cursor is under the first digit. Select [1].
• The cursor moves to the second digit. Select [2].
• To accept the change press [SET] then [RESET]
OR to cancel the change press the [RESET] button twice.
72 = Set Up Bell Delay
This...](http://img.usermanuals.tech/thumb/35/62752/w64_honeywell-accenta-8-user-manual-1491295022_d-29.png "Page 30
Accenta/Optima Engineer’s Manual
26
Timers (cont’d)
LCD keypad:
To change the Bell Delay time from 00 to 12 minutes:
•Press [up arrow] for menu Set Up Timers.
•Press [7]or [SET]. Option 1 Set up Bell Time appears.
•Press [2]. The Bell Delay time in minutes is displayed.
• The cursor is under the first digit. Select [1].
• The cursor moves to the second digit. Select [2].
• To accept the change press [SET] then [RESET]
OR to cancel the change press the [RESET] button twice.
72 = Set Up Bell Delay
This...")
![Page 31
Accenta/Optima Engineer’s Manual
27
Timers (cont’d)
LED Keypad:
To change the Rearm Count:
.
•Press [7] to enter Set Up Timers.LED’s 1, 2 and 3 are on.
•Press [3] for Rearm Count. LED 1 is on.
•Select a number [0 - 9] to change the rearm count.
•To accept the change press [SET]. LED’s 1, 2 and 3 are
on. Press [RESET].
OR to cancel the change press the [RESET] button twice.
73 = Set Up Rearm Count
After an alarm the panel will automatically rearm itself when the external siren (Bell) timer has expired....](http://img.usermanuals.tech/thumb/35/62752/w64_honeywell-accenta-8-user-manual-1491295022_d-30.png "Page 31
Accenta/Optima Engineer’s Manual
27
Timers (cont’d)
LED Keypad:
To change the Rearm Count:
.
•Press [7] to enter Set Up Timers.LED’s 1, 2 and 3 are on.
•Press [3] for Rearm Count. LED 1 is on.
•Select a number [0 - 9] to change the rearm count.
•To accept the change press [SET]. LED’s 1, 2 and 3 are
on. Press [RESET].
OR to cancel the change press the [RESET] button twice.
73 = Set Up Rearm Count
After an alarm the panel will automatically rearm itself when the external siren (Bell) timer has expired....")
![Page 32
Accenta/Optima Engineer’s Manual
28
To change the other codes: Press the [up arrow] to move through the codes.
[2] = User 2
[3] = Duress
[4] = Engineer LCD Keypad:
To change User code:
• Press the [8] button on the keypad or press the
[up arrow] for Set Up Codes. Then press [SET].
• Press the [1] or [SET] button on the keypad to
edit user code.
• Enter the new [4-digit code].
• Upon the last keypress the code is saved.
8 = Set Up Codes
There are four codes used in the system, all are 4 digit and can be...](http://img.usermanuals.tech/thumb/35/62752/w64_honeywell-accenta-8-user-manual-1491295022_d-31.png "Page 32
Accenta/Optima Engineer’s Manual
28
To change the other codes: Press the [up arrow] to move through the codes.
[2] = User 2
[3] = Duress
[4] = Engineer LCD Keypad:
To change User code:
• Press the [8] button on the keypad or press the
[up arrow] for Set Up Codes. Then press [SET].
• Press the [1] or [SET] button on the keypad to
edit user code.
• Enter the new [4-digit code].
• Upon the last keypress the code is saved.
8 = Set Up Codes
There are four codes used in the system, all are 4 digit and can be...")
![Page 33
Accenta/Optima Engineer’s Manual
29
Codes (cont’d)
LED Keypad:
To change User code:
• Press [8] to edit user code. LED’s 1-4 are on.
• Press [1] or [SET] to edit user code 1. LED’s 1-4 are on.
• Enter the new 4-digit code.
• Upon the last keypress the new code is saved.
• To leave menu press [RESET] twice.
The other codes are changed in a similar manner from step 2;
Press [2] for User 2
Press [3] for Duress code
Press [4] for Engineer code.
NOTE:To delete the 4-digit code from User 2 or Duress, enter...](http://img.usermanuals.tech/thumb/35/62752/w64_honeywell-accenta-8-user-manual-1491295022_d-32.png "Page 33
Accenta/Optima Engineer’s Manual
29
Codes (cont’d)
LED Keypad:
To change User code:
• Press [8] to edit user code. LED’s 1-4 are on.
• Press [1] or [SET] to edit user code 1. LED’s 1-4 are on.
• Enter the new 4-digit code.
• Upon the last keypress the new code is saved.
• To leave menu press [RESET] twice.
The other codes are changed in a similar manner from step 2;
Press [2] for User 2
Press [3] for Duress code
Press [4] for Engineer code.
NOTE:To delete the 4-digit code from User 2 or Duress, enter...")
![Page 34
Accenta/Optima Engineer’s Manual
30
C = View Event Log
1 = LCD Keypad:
The event log gives a display of all the events that have taken place. The events are arranged by date and time.
Up to 250 events can be stored in the memory. When the log reaches 250 events and another event takes
place, the first event drops out. The system is known as FILO (First In Last Out).
To view the event log:
• Press the [up arrow] until you come to the first screen.
• Press [CHIME] or [SET] .
• Choose [1] for Event Log in...](http://img.usermanuals.tech/thumb/35/62752/w64_honeywell-accenta-8-user-manual-1491295022_d-33.png "Page 34
Accenta/Optima Engineer’s Manual
30
C = View Event Log
1 = LCD Keypad:
The event log gives a display of all the events that have taken place. The events are arranged by date and time.
Up to 250 events can be stored in the memory. When the log reaches 250 events and another event takes
place, the first event drops out. The system is known as FILO (First In Last Out).
To view the event log:
• Press the [up arrow] until you come to the first screen.
• Press [CHIME] or [SET] .
• Choose [1] for Event Log in...")
![Page 36
Accenta/Optima Engineer’s Manual
32
LED Keypad:
Press [CHIME] to toggle double knock status on or off.
Press [9] to turn all double knock zones on.
Press [0] to turn all double knock zones off.
• Press [OMIT] to enter into menu. LED’s 1 and 2 are on.
• Press [1] to select Double Knock.
• Press zone number [1-8] to choose a particular zone.
• Press the zone [number] or [CHIME] to toggle the double
knock status on or off. The appropriate LED is on when the zone is
set up as Double Knock. Default settings...](http://img.usermanuals.tech/thumb/35/62752/w64_honeywell-accenta-8-user-manual-1491295022_d-35.png "Page 36
Accenta/Optima Engineer’s Manual
32
LED Keypad:
Press [CHIME] to toggle double knock status on or off.
Press [9] to turn all double knock zones on.
Press [0] to turn all double knock zones off.
• Press [OMIT] to enter into menu. LED’s 1 and 2 are on.
• Press [1] to select Double Knock.
• Press zone number [1-8] to choose a particular zone.
• Press the zone [number] or [CHIME] to toggle the double
knock status on or off. The appropriate LED is on when the zone is
set up as Double Knock. Default settings...")
Accenta/Optima Engineer’s Manual 27 Timers (cont’d) LED Keypad: To change the Rearm Count: . •Press [7] to enter Set Up Timers.LED’s 1, 2 and 3 are on. •Press [3] for Rearm Count. LED 1 is on. •Select a number [0 - 9] to change the rearm count. •To accept the change press [SET]. LED’s 1, 2 and 3 are on. Press [RESET]. OR to cancel the change press the [RESET] button twice. 73 = Set Up Rearm Count After an alarm the panel will automatically rearm itself when the external siren (Bell) timer has expired. Any zones which still remain open at that time will be automatically omitted . The default is 3 rearms. 0 = no rearms 1-8 = number of rearms 9 = always rearm LCD keypad: To change the Rearm Count: •Press [up arrow] for menu Set Up Timers. •Press [7]or [SET]. Option 1 Set up Bell Time appears. •Press [3]. The Rearm Count is displayed (default 3). • Select a number [0 - 9] to change the rearm count. • To accept the change press [SET] then [RESET] •OR to cancel the change press the [RESET] button twice. [7] [SET] then [RESET] or [RESET] [3] [Number] 1234 5 678 1234 5 678 1234 5 678 7>Set Up 7>Set Up7>Set Up 7>Set Up 7>Set Up Timers Timers Timers Timers Timers Rearm Count Rearm CountRearm Count Rearm Count Rearm Count 3 33 3 3[3] 71>Set Up 71>Set Up71>Set Up 71>Set Up 71>Set Up Bell Time Bell Time Bell Time Bell Time Bell Time[7] or [SET] 7>Set Up 7>Set Up7>Set Up 7>Set Up 7>Set Up Timers Timers Timers Timers Timersor [RESET] 73>Set Up 73>Set Up73>Set Up 73>Set Up 73>Set Up Rearm Count Rearm Count Rearm Count Rearm Count Rearm Count[SET] then [RESET] [up arrow] 1234 5 678
Accenta/Optima Engineer’s Manual 28 To change the other codes: Press the [up arrow] to move through the codes. [2] = User 2 [3] = Duress [4] = Engineer LCD Keypad: To change User code: • Press the [8] button on the keypad or press the [up arrow] for Set Up Codes. Then press [SET]. • Press the [1] or [SET] button on the keypad to edit user code. • Enter the new [4-digit code]. • Upon the last keypress the code is saved. 8 = Set Up Codes There are four codes used in the system, all are 4 digit and can be set to any number from 0000 to 9999. The access codes ensure that only authorised users can operate the system. User 1 and 2 codes The user 1 and user 2 codes have the same operation for testing, Setting and Unsetting, but user 1 code which is usually considered to be the Manager’s code has the authority to add, change or delete the user 2 code and duress code. Duress code Should be used in a hold up situation where there is pressure to Set or Unset the system. Entry of the code will allow the system to work normally but also generate a silent PA type alarm by operating the PA communi- cator output. The duress code is not applicable for Optima compact system. Engineer code Accesses the Engineer program mode to allow the system to be programmed. The engineer code will not set or unset the system. If configured the Engineer’s code can be used to reset the system after an alarm. NOTE:Entering an invalid user code will operate the code tamper. After 17 incorrect keypushes a full alarm condition will be generated. Codes (cont’d) 8>Set Up 8>Set Up8>Set Up 8>Set Up 8>Set Up User 1 User 1User 1 User 1 User 1 Edit Code Edit CodeEdit Code Edit Code Edit Code ---- -------- ---- ---- Code Saved Code SavedCode Saved Code Saved Code Saved[8] or [up arrow] then [SET] [1] or [SET] [4-digit code]
Accenta/Optima Engineer’s Manual 29 Codes (cont’d) LED Keypad: To change User code: • Press [8] to edit user code. LED’s 1-4 are on. • Press [1] or [SET] to edit user code 1. LED’s 1-4 are on. • Enter the new 4-digit code. • Upon the last keypress the new code is saved. • To leave menu press [RESET] twice. The other codes are changed in a similar manner from step 2; Press [2] for User 2 Press [3] for Duress code Press [4] for Engineer code. NOTE:To delete the 4-digit code from User 2 or Duress, enter into Edit Code and press [OMIT]. [8] 1234 5 678 [1] or [SET] [4-digit code] 1234 5 678 1234 5 678
Accenta/Optima Engineer’s Manual 30 C = View Event Log 1 = LCD Keypad: The event log gives a display of all the events that have taken place. The events are arranged by date and time. Up to 250 events can be stored in the memory. When the log reaches 250 events and another event takes place, the first event drops out. The system is known as FILO (First In Last Out). To view the event log: • Press the [up arrow] until you come to the first screen. • Press [CHIME] or [SET] . • Choose [1] for Event Log in LCD screen. • The last event (250) appears on LCD screen. To go forward through the event log in sequence, press [OMIT]. To go back through the event log in sequence, press the [up arrow]. • Press [RESET] twice to leave the menu To go to a specific event: • Press the [PROG] button. • Key in Event Number you want to see (eg 150). • Press the [SET] button. The event appears on the LCD screen. • Press [SET] again to see further details of the event. • Press [RESET] twice to leave the menu option. Event Log 250>ENG ACCESS 250>ENG ACCESS250>ENG ACCESS 250>ENG ACCESS 250>ENG ACCESS 08:44:03 17-May 08:44:03 17-May08:44:03 17-May 08:44:03 17-May 08:44:03 17-May C>View C>ViewC>View C>View C>View Event Log Event Log Event Log Event Log Event Log [CHIME] or [SET] Event Log Event LogEvent Log Event Log Event Log 1 LCD, 2 LED? 1 LCD, 2 LED?1 LCD, 2 LED? 1 LCD, 2 LED? 1 LCD, 2 LED? [1] Event Number? Event Number?Event Number? Event Number? Event Number? ### ###### ### ###[PROG] [150] 150>Code entry 150>Code entry150>Code entry 150>Code entry 150>Code entry 09:23:12 04-Jan 09:23:12 04-Jan09:23:12 04-Jan 09:23:12 04-Jan 09:23:12 04-Jan[SET] [SET] [RESET] Event Number? Event Number?Event Number? Event Number? Event Number? 150 150150 150 150 User 4 User 4User 4 User 4 User 4 C>View C>ViewC>View C>View C>View Event Log Event LogEvent Log Event Log Event Log
Accenta/Optima Engineer’s Manual 31 2 = LED Keypad: The LED keypad is limited to show the last eight set periods with the eighth being the oldest. Zone, PA and Tamper indicators will be lit to show zone in alarm . Flashing LED indicates the first zone in alarm. Day indi- cates the status of the panel at the time of the alarm. O = Omit Allow and Double Knock 1 = Double Knock Double knock programming is used when zones are likely to create false activations. Double knock requires two activations within 10 minutes of the same zone or a zone left open for 10 seconds. NOTE:It is not advisable to apply Double Knock to magnetic door contacts. Double Knock cannot be applied to Fire Zones. By default, no zones are in Double Knock mode and all zones are enabled as Omit Allow. LCD Keypad: Programming a Zone as Double Knock The [up arrow] scrolls through zones. Press [CHIME] to toggle double knock status on or off. Press [9] to turn all double knock zones on. Press [0] to turn all double knock zones off. • Press [CHIME] to enter into Event Log menu. LED’s 1 and 2 are on. • Press [2] for LED keypad. The first zone to activate is indicated by a flashing LED. • Press [1 to 8] for the desired event or [CHIME] to go through events in sequence. • Press [RESET] twice to leave the menu. While in Engineer program mode press [OMIT] or press [up arrow] until 0>Omit allow & Double Knock is displayed then press [SET]. • Press [1] to select Double Knock. The first zone is displayed with status NO or YES. • Press the [zone number] or [CHIME] to toggle the status on or off. • Press the [up arrow] or [zone number] to go to the other zones and follow the same procedure as above. • Press [RESET] twice to leave the menu. 1. Double Knock 1. Double Knock1. Double Knock 1. Double Knock 1. Double Knock 2. Omit Allow 2. Omit Allow2. Omit Allow 2. Omit Allow 2. Omit Allow[OMIT] [1] [RESET] Omit Allow & Omit Allow &Omit Allow & Omit Allow & Omit Allow & Double Knock Double KnockDouble Knock Double Knock Double Knock 1: 1: 1: 1: 1: Double Knock:NO Double Knock:NODouble Knock:NO Double Knock:NO Double Knock:NO 1: 1: 1: 1: 1: Double Knock:YES Double Knock:YESDouble Knock:YES Double Knock:YES Double Knock:YES[zone number] or [CHIME] Event Log (cont’d) 1234 5 678 [CHIME] [RESET] 1234 5 678
Accenta/Optima Engineer’s Manual 32 LED Keypad: Press [CHIME] to toggle double knock status on or off. Press [9] to turn all double knock zones on. Press [0] to turn all double knock zones off. • Press [OMIT] to enter into menu. LED’s 1 and 2 are on. • Press [1] to select Double Knock. • Press zone number [1-8] to choose a particular zone. • Press the zone [number] or [CHIME] to toggle the double knock status on or off. The appropriate LED is on when the zone is set up as Double Knock. Default settings are off. • Press [RESET] twice to leave the menu. 2 = Omit Allow When a zone is programmed as Omit Allow, the panel allows the zone to be omitted for one set period by the user when setting the system. Programming a Zone as Omit Allow The [up arrow] scrolls through zones. Press [CHIME] to toggle omit allow status on or off. Press [9] to turn all omit allow zones on. Press [0] to turn all omit allow zones off. LCD Keypad: While in Engineer program mode press [OMIT]or press [up arrow] until 0>Omit allow & Double Knock is displayed then press [SET]. • Press [2] to select Omit Allow. The first zone is displayed with status on or off. • Press the [zone number] or [CHIME] to toggle the status on or off. • Press the [up arrow] or [zone number] to go to the other zones and follow the same procedure as above. • Press [RESET] twice to leave the menu. 1. Double Knock 1. Double Knock1. Double Knock 1. Double Knock 1. Double Knock 2. Omit Allow 2. Omit Allow2. Omit Allow 2. Omit Allow 2. Omit Allow[OMIT] [2] [RESET] Omit Allow & Omit Allow &Omit Allow & Omit Allow & Omit Allow & Double Knock Double KnockDouble Knock Double Knock Double Knock 2: 2: 2: 2: 2: Omit Allow:NO Omit Allow:NOOmit Allow:NO Omit Allow:NO Omit Allow:NO 2: 2: 2: 2: 2: Omit Allow:YES Omit Allow:YESOmit Allow:YES Omit Allow:YES Omit Allow:YES[zone number] or [CHIME] Omit Allow & Double Knock [OMIT] [1] 1234 5 678 [1-8] or [CHIME] [RESET] 1234 5 678 1234 5 678 1234 5 678
Accenta/Optima Engineer’s Manual 33 Omit Allow & Double Knock LED Keypad: Press [CHIME] to toggle omit allow status on or off. Press [9] to turn all omit allow zones on. Press [0] to turn all omit allow zones off. • Press [OMIT] to enter into menu. LED 2 is on. • Press [2] to select Omit Allow. • Press zone number [1-8] to choose a particular zone. • Press the [zone number] or [CHIME] to toggle the omit allow status on or off. The appropriate LED is on when the zone is set up as omit allow. Default settings are off. • Press [RESET] twice to leave the menu.[OMIT] [2] [1-8] or [CHIME] [RESET] 1234 5 678 1234 5 678 1234 5 678 1234 5 678
Accenta/Optima Engineer’s Manual 34 P = Set Up Programs The panel uses three setting routines known as programs. Each program may have a different Exit Mode. These are 0 = Disabled, 1 = Timed, 2 = Final Door or 3 = Silent Timed. Zones can also be assigned different functions in different programs. Refer to the following diagram for the programming structure. Figure 16. Programming structure Programs P>Set Up Programs Select Program 1, 2 or 3 1 = Used Zones Zones 01-08 (Yes/No) 2 = Timed Zones Zones 01-08 (Yes/No) 3 = Inhibit ZonesZones 01-08 (Yes/No) 4 = Entry Time 6 = Exit Mode 0 = DISABLED 1 = TIMED 2 = FINAL DOOR 3 = SILENT TIMED 00-99 (multiplied by 10) 5 = Exit Time 00-99 (multiplied by 10) Notes on Zones For any program a zone cannot be both timed and inhibited. If a zone is selected as one it will be removed from the other. Zones in the timed and inhibited lists will be automatically added to the used list. Zones removed from the used list will be removed from the timed and inhibited lists. If a timed zone is left open on rearm, any inhibit zones will act as a timed zone during that set period. 1 = Used Zones The zones on the system can either be programmed as Used or Unused. A zone that is programmed as unused by the engineer, is still available for chime or fire. Unused zones are primarily used for Part Set options. There must always be at least one used zone in program 1. The panel will enforce this if none are selected by auto- matically setting zone 1 to used.
Accenta/Optima Engineer’s Manual 35 LCD Keypad: NOTE:Pressing the number toggles the zone ON or OFF While in Engineer program mode, to set up zones as used, • Press [PROG] to give a choice of programs or press [up arrow] until P>Set Up Programs is displayed then press [SET]. • Select program 1, 2 or 3. • The first screen to appear is Program Edit Used Zones. • Press [1] or [SET]. The first zone can now be set as used or unused. • To edit the other zones press [Number] or [up arrow] to go to a particular zone. • Press [RESET] three times to leave menu. LED Keypad: NOTE:Pressing the number toggles the zone ON or OFF While in Engineer program mode, to set up zones as used, • Press [PROG] to give a choice of programs. LED’s 1, 2 and 3 are flashing. • Select program [1, 2 or 3]. If program 1 is selected, LED 1 is ON. • Press [1] or [SET]. The first zone can now be set as used or unused. If used, then LED is on • To edit the other zones press [Number] to go to a particular zone. Default settings are on. • Press [RESET] three times to leave menu.[PROG] [1] [1] or [SET] [RESET] 1234 5 678 1234 5 678 [Number] Programs (cont’d) [PROG] [1] or [SET] 1: Descriptor 1: Descriptor1: Descriptor 1: Descriptor 1: Descriptor Used: Used:Used: Used: Used: YES YESYES YES YES P>Select Program P>Select ProgramP>Select Program P>Select Program P>Select Program 1 2 or 3 1 2 or 31 2 or 3 1 2 or 3 1 2 or 3 P>Program Edit P>Program EditP>Program Edit P>Program Edit P>Program Edit Used Zones Used Zones Used Zones Used Zones Used Zones[Number] [Number] or [up arrow] 2: Descriptor 2: Descriptor2: Descriptor 2: Descriptor 2: Descriptor Used: Used:Used: Used: Used: NO NONO NO NO [RESET] P>Set Up P>Set UpP>Set Up P>Set Up P>Set Up Programs Programs Programs Programs Programs 1234 5 678 1234 5 678 1234 5 678
Accenta/Optima Engineer’s Manual 36 2 = Timed Zones A zone programmed as Timed would be used to protect the main entry/exit door of the entry route. LCD Keypad: NOTE:Pressing the number toggles the zone ON or OFF While in Engineer program mode, to set up zones as timed, • Press [PROG] to give a choice of programs or press [up arrow] until P>Set Up Programs is displayed then press [SET]. • Select program 1, 2 or 3. • The first screen to appear is Program Edit Used Zones. • Press [2] to enter into Timed Zones. The first zone can now be set as timed or untimed. • To edit the other zones press [Number] or [up arrow] to go to a particular zone. • Press [RESET] three times to leave menu.[PROG] [2] 1: Descriptor 1: Descriptor1: Descriptor 1: Descriptor 1: Descriptor Timed: Timed:Timed: Timed: Timed: YES YESYES YES YES P>Select Program P>Select ProgramP>Select Program P>Select Program P>Select Program 1 2 or 3 1 2 or 31 2 or 3 1 2 or 3 1 2 or 3 P>Program Edit P>Program EditP>Program Edit P>Program Edit P>Program Edit Used Zones Used Zones Used Zones Used Zones Used Zones[Number] [Number] or [up arrow] 2: Descriptor 2: Descriptor2: Descriptor 2: Descriptor 2: Descriptor Timed: Timed:Timed: Timed: Timed: NO NONO NO NO [RESET] P>Set Up P>Set UpP>Set Up P>Set Up P>Set Up Programs Programs Programs Programs Programs LED Keypad: NOTE:Pressing the number toggles the zone ON or OFF While in Engineer program mode, to set up zones as timed, • Press [PROG] to give a choice of programs. LED’s 1, 2 and 3 are flashing. • Select program [1, 2 or 3]. If program 1 is selected, LED 1 is ON. • Press [2] to enter into Timed Zones. The first zone can now be set as timed or untimed. • To edit the other zones press [Number] to go to a particular zone. Default settings are shown opposite. • Press [RESET] three times to leave menu.[PROG] [1] [2] [RESET] 1234 5 678 1234 5 678 1234 5 678 [Number] Programs (cont’d) 1234 5 678 1234 5 678