Honeywell 20205 Manual

							10 - 3
Responses
The device responds to serial commands with one of three responses:
ACKIndicates a good command which has been processed.
ENQIndicates an invalid Tag or SubTag command. 
NAKIndicates the command was good, but the Data field entry was out of the 
allowable range for this Tag and SubTag combination, e.g., an entry for a mini-
mum message length of 100 when the field will only accept 2 characters.
When responding, the device echoes back the command sequence with the 
status character inserted directly before each of the punctuation marks (the 
period, exclamation point, comma, or semicolon) in the command.
Examples of Query Commands
In the following examples, a bracketed notation [   ] depicts a non-displayable 
response.
Example #1:What is the range of possible values for Codabar Coding Enable?
Enter: cbrena*.
Response: CBRENA0-1[ACK]
This response indicates that Codabar Coding Enable (CBRENA) has a range of 
values from 0 to 1 (off and on).  
Example #2:  What is the default value for Codabar Coding Enable?
Enter: cbrena^.
Response: CBRENA1[ACK]
This response indicates that the default setting for Codabar Coding Enable 
(CBRENA) is 1, or on.  
Example #3:  What is the device’s current setting for Codabar Coding Enable?
Enter: cbrena?.
Response: CBRENA1[ACK]
This response indicates that the device’s Codabar Coding Enable (CBRENA) is 
set to 1, or on.   
						

							10 - 4
Example #4:  What are the device’s settings for all Codabar selections?
Enter: cbr?.
Response: CBRENA1[ACK],
SSX0[ACK],
CK20[ACK],
CCT1[ACK],
MIN2[ACK],
MAX60[ACK],
DFT[ACK].
This response indicates that the device’s Codabar Coding Enable (CBRENA) is 
set to 1, or on; 
the Start/Stop Character (SSX) is set to 0, or Don’t Transmit; 
the Check Character (CK2) is set to 0, or Not Required;
concatenation (CCT) is set to 1, or Enabled; 
the Minimum Message Length (MIN) is set to 2 characters; 
the Maximum Message Length (MAX) is set to 60 characters; 
and the Default setting (DFT) has no value.  
Trigger Commands
You can activate and deactivate the image scanner with serial trigger com-
mands.  First, the image scanner must be put in Manual/Serial Trigger Mode 
either by scanning the Manual/Serial Trigger Mode bar code (page 3-3), or by 
sending the Manual/Serial Menu Command (page 10-12).  Once the image 
scanner is in serial trigger mode, the trigger is activated and deactivated by 
sending the following commands:
Activate:SYN T CR
Deactivate:SYN U CR
The image scanner scans until a bar code has been read, until the deactivate 
command is sent, or until the serial time-out has been reached (see Read 
Time-Out (Serial Trigger Mode)on page 3-4 for a description, and the serial 
command on page 10-12).
Resetting the Standard Product Default Settings:
Current Application Work Group
If you aren’t sure what programming options are in your image scanner, or 
you’ve changed some options and want the standard product default settings 
restored, scan the 
Standard Product Default Settings: Current Application 
Group bar code below. 
						

							10 - 5
The Menu Commands starting on page 10-6 list the factory default settings for 
each of the commands (indicated by an asterisk (*) on the programming pages).
Note: Scanning this bar code also causes both the image scanner and the base 
to perform a reset and become unlinked.  Refer to Linking Image 
Scanner to Baseon page 1-5 for additional information.
Note: If your image scanner is in multiple image scanner mode and you scan 
either the current or all application group default bar code, you will hear 
up to 30 seconds of beeping while all image scanners are re-linked from 
the base and the settings are defaulted to * settings.  The default interface 
is keyboard wedge and the default image scanner mode is single image 
scanner locked link mode.
Resetting the Standard Product Default Settings: 
All Application Work Groups
The following bar code defaults all of the work groups to the factory settings.
The Menu Commands starting on page 10-6 list the standard product default 
settings for each of the commands (indicated by an asterisk (*) on the program-
ming pages).
Standard Product Default Settings: 
Current Application Group
 Standard Product Default Settings:
All Application Groups 
						

							10 - 6
Menu Commands
SelectionSetting* Indicates default
Serial 
Command
# Indicates a 
numeric entryPage
Base Charge Mode *Automatic
BASCHG11-4
Full Charge Rate
BASCHG21-4
Low Charge Rate
BASCHG31-4
Battery Charge Off
BASCHG41-4
Image Scanner Modes 
- SingleUnlink Image Scanner
BT_RMV1-5
*Locked Link Mode
BASCON0,DNG11-6
Open Link Mode
BASCON1,DNG11-6
Override Locked Image 
Scanner
BT_RPL11-6
Multiple Image Scan-
ner
OperationMultiple Image Scan-
ner Operation
BASCON2,DNG3
1-7
Image Scanner NameImage Scanner Name
BT_NAM1-8
Image Scanner Report Image Scanner Report
RPTSCN1-9
Application Work 
Group
Selections*Group 0
GRPSEL01-10
Group 1
GRPSEL11-10
Group 2
GRPSEL21-10
Group 3
GRPSEL31-10
Group 4
GRPSEL41-10
Group 5
GRPSEL51-10
Group 6
GRPSEL61-10
Standard Product 
Defaults: Current 
Application Work 
GroupDefault - Current Work 
Group
DEFALT
1-11
Standard Product 
Defaults: All Applica-
tion Work GroupsDefault - All Work 
Groups
PAPDFT
1-11
Non-Base Bluetooth
ConnectionNon-Base BT Connec-
tion
BT_DNG51-12
Bluetooth PIN Code Bluetooth PIN
BT_PIN1-12 
						

							10 - 7
Out-of-Range Alarm Base Alarm Duration 
(Range 1 - 3000 sec 
(*0))
BASORD
1-13
Image Scanner Alarm 
Duration (Range 1 - 
3000 sec (*0))
BT_ORD1-13
Alarm Sound Type Base Alarm Type
BASORW1-13
Image Scanner Alarm 
Ty p e
BT_ORW1-13
Data Accumulation 
ModeOn
BATENA11-13
*Off
BATENA01-13
Batch Mode Transmit 
Delay*Off
BATDLY01-14
Short (ms)
BATDLY2501-14
Medium (ms)
BATDLY5001-14
Long (ms)
BATDLY10001-14
Factory Default Set-
tingsDefault
DEFALT1-20
Terminal Interfaces
Terminal ID *003TERMID###2-2 SelectionSetting
* Indicates default
Serial 
Command
# Indicates a 
numeric entryPage 
						

							10 - 8
Program Keyboard 
Country*U.S.A.KBDCTY02-4
Belgium
KBDCTY12-4
Brazil
KBDCTY162-4
Canada (French)
KBDCTY182-4
Czech Republic
KBDCTY152-4
Denmark
KBDCTY82-4
Finland (Sweden)
KBDCTY22-4
France
KBDCTY32-4
Germany/Austria
KBDCTY42-4
Greece
KBDCTY172-4
Hungary
KBDCTY192-4
Israel (Hebrew)
KBDCTY122-4
Italy
KBDCTY52-5
Latin America
KBDCTY142-5
Netherlands (Dutch)
KBDCTY112-5
Norway
KBDCTY92-5
Pola nd
KBDCTY202-5
Portugal
KBDCTY132-5
Romania
KBDCTY252-5
Russia
KBDCTY262-5
SCS
KBDCTY212-5
Slovakia
KBDCTY222-5
Spain
KBDCTY102-5
Sweden
KBDCTY232-5
Switzerland (German)
KBDCTY62-5
Tu r k e y  F
KBDCTY272-5
Tu r k e y  Q
KBDCTY242-5
U.K.
KBDCTY72-5 SelectionSetting
* Indicates default
Serial 
Command
# Indicates a 
numeric entryPage 
						

							10 - 9
Keyboard Style *RegularKBDSTY02-6
Caps Lock
KBDSTY12-6
Shift Lock
KBDSTY22-6
Automatic Caps Lock
KBDSTY62-6
Emulate External
Keyboard
KBDSTY52-6
Keyboard Modifiers *Control + ASCII Off
KBDCAS02-7
Control + ASCII On
KBDCAS22-7
*Turbo Mode Off
KBDTMD02-7
Turbo Mode On
KBDTMD12-7
*Numeric Keypad Off
KBDNPS02-7
Numeric Keypad On
KBDNPS12-7
*Auto Direct Conn. Off
KBDADC02-7
Auto Direct Conn. On
KBDADC12-7
Serial Port Connection RS-232
PAP2322-8
Baud Rate 300 BPS
232BAD02-9
600 BPS
232BAD12-9
1200 BPS
232BAD22-9
2400 BPS
232BAD32-9
4800 BPS
232BAD42-9
9600 BPS
232BAD52-9
19200 BPS
232BAD62-9
38400 BPS
232BAD72-9
57600 BPS
232BAD82-9
*115200 BPS
232BAD92-9 SelectionSetting
* Indicates default
Serial 
Command
# Indicates a 
numeric entryPage 
						

							10 - 10
Word Length:  Data 
Bits, Stop Bits, and 
Par ity7 Data, 1 Stop, Parity 
Even232WRD32-10
7 Data, 1 Stop, Parity 
None
232WRD02-10
7 Data, 1 Stop, Parity 
Odd
232WRD62-10
7 Data, 2 Stop, Parity 
Even
232WRD42-10
7 Data, 2 Stop, Parity 
None
232WRD12-10
7 Data, 2 Stop, Parity 
Odd
232WRD72-10
8 Data, 1 Stop, Parity 
Even
232WRD52-10
*8 Data, 1 Stop, Parity 
None
232WRD22-10
8 Data, 1 Stop, Parity 
Odd
232WRD82-10
RS-232 Handshaking *RTS/CTS Off
232CTS02-11
RTS/CTS On
232CTS22-11
*XON/XOFF Off
232XON02-11
XON/XOFF On
232XON12-11
*ACK/NAK Off
232ACK02-11
ACK/NAK On
232ACK12-11
Wand Emulation Con-
nectionSame Code Format
TERMID642-14
Code 39 Format
TERMID612-14
Wand Emulation 
Transmission Rate10
WNDSPD02-15
*25
WNDSPD12-15
40
WNDSPD22-15
80
WNDSPD32-15
120
WNDSPD42-15
150
WNDSPD52-15
200
WNDSPD62-15 SelectionSetting
* Indicates default
Serial 
Command
# Indicates a 
numeric entryPage 
						

							10 - 11
Wand Emulation Polar-
ity*Black HighWNDPOL02-15
White High
WNDPOL12-15
Wand Emulation Idle Idle Low
WNDIDL02-15
*Idle High
WNDIDL12-15
Wand Emulation Data 
Block Size20
WNDBLK02-16
*40
WNDBLK12-16
60
WNDBLK22-16
80
WNDBLK32-16
Wand Emulation Delay 
Between Blocks5ms
WNDDLY02-16
*50ms
WNDDLY12-16
150ms
WNDDLY22-16
500ms
WNDDLY32-16
Wand Emulation Over-
all Checksum*Off
WNDCHK02-16
On
WNDCHK12-16
Output Selections
Beeper - Good Read  OffBEPBEP03-1
*On
BEPBEP13-1
Beeper Volume - Good 
ReadOff
BEPLVL03-1
Low
BEPLVL13-1
*Medium
BEPLVL23-1
High
BEPLVL33-1
Beeper Pitch - Good 
Read  (Frequency)Low (1600) (min 
400Hz)
BEPFQ116003-2
*Medium (3250)
BEPFQ132503-2
High (4200) (max 
9000Hz)
BEPFQ142003-2
Beeper Duration - 
Good Read*Normal Beep
BEPBIP03-2
Short Beep
BEPBIP13-2
LED - Good Read  Off
BEPLED03-2
*On
BEPLED13-2 SelectionSetting
* Indicates default
Serial 
Command
# Indicates a 
numeric entryPage 
						

							10 - 12
Number of Beeps - 
Good Read *1BEPRPT13-2
Range 1 - 9
BEPRPT#3-2
Good Read Delay *No Delay
DLYGRD03-3
Short Delay (500 ms)
DLYGRD5003-3
Medium Delay (1000 
ms)
DLYGRD10003-3
Long Delay (1500 ms)
DLYGRD15003-3
User-Specified Good 
Read DelayRange 0 - 30,000 ms
DLYGRD#####3-3
Trigger Mode *Manual Trigger
TRGMOD03-3
Read Time-Out (0 - 
300,000 ms) *30,000
TRGSTO####3-4
Image Scanner Power 
Time-Out Timer (0-
7200 seconds) *3600
BT_LPT03-5
BT_LPT2003-5
BT_LPT4003-5
BT_LPT9003-5
BT_LPT36003-5
BT_LPT72003-5
Automatic Trigger
TRGMOD13-5
Presentation Mode
TRGMOD33-5
Hands Free Time-Out 
(0-300,000 seconds) 
*5000
TRGPTO######
3-6
Reread Delay Short (500 ms)
DLYRRD5003-6
*Medium (750 ms)
DLYRRD7503-6
Long (1000 ms)
DLYRRD10003-6
Extra Long (2000 ms)
DLYRRD30003-6
User-Specified Reread 
DelayRange 0 - 30,000 ms
DLYRRD#####3-6 SelectionSetting
* Indicates default
Serial 
Command
# Indicates a 
numeric entryPage