Honeywell 20205 Manual

							6 - 1
6
Symbologies
Introduction
This programming section contains the following menu selections.  Refer to 
Chapter 10 for settings and defaults.
All Symbologies
If you want to decode all the symbologies allowable for your image scanner, 
scan the All Symbologies On code.  If on the other hand, you want to decode 
only a particular symbology, scan All Symbologies Off followed by the On sym-
bol for that particular symbology.All SymbologiesInterleaved 2 of 5
China Post CodeKorea Post Code
CodabarMatrix 2 of 5
Codablock FUPC-A/EAN-13 with 
Extended Coupon 
Code
Code 11MSI
Code 16KPlessey Code
Code 39PosiCode A and B
Code 32 Pharmaceutical (PARAF)Straight 2 of 5 IATA 
(two-bar start/stop)
Code 39Straight 2 of 5 
Industrial
Code 49Telepen
Code 93Codablock F
Code 128UPC A
EAN/JAN 8UPC E0 and UPC E1
GS1 DataBar Limited
All Symbologies On
All Symbologies Off 
						

							6 - 2
Message Length
You are able to set the valid reading length of some of the bar code symbologies.   
If the data length of the scanned bar code doesn’t match the valid reading length, 
the image scanner will issue an error beep.  You may wish to set the same value 
for minimum and maximum length to force the image scanner to read fixed 
length bar code data.  This helps reduce the chances of a misread.
EXAMPLE:Decode only those bar codes with a count of 9-20 characters.
Min. length = 09 Max. length = 20
EXAMPLE:Decode only those bar codes with a count of 15 characters.
Min. length = 15 Max. length = 15
For a value other than the minimum and maximum message length defaults, 
scan the bar codes included in the explanation of the symbology, then scan the 
digit value of the message length and Save bar codes on the Programming Chart 
inside the back cover of this manual.  The minimum and maximum lengths and 
the defaults are included with the respective symbologies. 
						

							6 - 3
Codabar

Codabar
Codabar Start / Stop Characters
Start/Stop characters identify the leading and trailing ends of the bar code. You 
may either transmit, or not transmit Start/Stop characters.  
Default = Don’t Transmit.
Codabar Check Character
Codabar check characters are created using different “modulos.”  You can pro-
gram the image scanner to read only Codabar bar codes with Modulo 16 check 
characters. 
 Default = No Check Character.
No Check Character
 indicates that the image scanner reads and transmits bar 
code data with or without a check character.
When Check Character is set to 
Validate and Transmit, the image scanner will 
only read Codabar bar codes printed with a check character, and will transmit 
this character at the end of the scanned data.
* On
Off
Transmit
* Don’t Transmit 
						

							6 - 4
When Check Character is set to Validate, but Don’t Transmit, the unit will only 
read Codabar bar codes printed with a check character, but will not transmit the 
check character with the scanned data.
Codabar Concatenation
Codabar supports symbol concatenation.  When you enable concatenation, the 
image scanner looks for a Codabar symbol having a “D” start character, adja-
cent to a symbol having a “D” stop character.  In this case the two messages 
are concatenated into one with the “D” characters omitted.
Select Require to prevent the image scanner from decoding a single “D” Coda-
bar symbol without its companion.  This selection has no effect on Codabar 
symbols without Stop/Start D characters.
* No Check Character
Validate Modulo 16 and TransmitValidate Modulo 16, but
Don’t Transmit
A12D D34A
Codabar
Character
Stop Start Stop Start
On
Off
Require 
						

							6 - 5
Codabar Message Length
Scan the bar codes below to change the message length.  Refer to Message 
Lengthon page 6-2 for additional information.  Minimum and Maximum
lengths = 2-60.  Minimum Default = 4, Maximum Default = 60.
Code 39
< Default All Code 39 Settings >
Code 39
Code 39 Start / Stop Characters
Start/Stop characters identify the leading and trailing ends of the bar code. You 
may either transmit, or not transmit Start/Stop characters.  Default =  Don’t 
Tr a n s m i t .
Minimum Message Length
Maximum Message Length
*  On
Off
Transmit
*  Don’t Transmit 
						

							6 - 6
Code 39, continued
Code 39 Check Character
No Check Character indicates that the image scanner reads and transmits bar 
code data with or without a check character.
When Check Character is set to Validate, but Don’t Transmit, the unit only 
reads Code 39 bar codes printed with a check character, but will not transmit 
the check character with the scanned data.  
When Check Character is set to Validate and Transmit, the image scanner 
only reads Code 39 bar codes printed with a check character, and will transmit 
this character at the end of the scanned data.  
Default = No Check Character.
Code 39 Message Length
Scan the bar codes below to change the message length.  Refer to Message 
Lengthon page 6-2 for additional information.  Minimum and Maximum
lengths = 0-48.  Minimum Default = 0, Maximum Default = 48.
Validate, but Don’t Transmit *  No Check Character
Validate and Transmit
Minimum Message Length
Maximum Message Length 
						

							6 - 7
Code 39, continued
Code 39 Append
This function allows the image scanner to append the data from several Code 
39 bar codes together before transmitting them to the host computer.  When this 
function is enabled, the image scanner stores those Code 39 bar codes that 
start with a space (excluding the start and stop symbols), and does not immedi-
ately transmit the data.  The image scanner stores the data in the order in which 
the bar codes are read, deleting the first space from each.  The image scanner 
transmits the appended data when it reads a Code 39 bar code that starts with 
a character other than a space.  
Default = Off.
Code 32 Pharmaceutical (PARAF)
Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian 
pharmacies.  This symbology is also known as PARAF..
*  Off On
*  Off On 
						

							6 - 8
Full ASCII
If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar 
code symbol will be interpreted as a single character.  For example:  $V will be 
decoded as the ASCII character SYN, and /C will be decoded as the ASCII 
character #.  
Default = On.
Character pairs /M and /N decode as a minus sign and period respectively.
Character pairs /P through /Y decode as 0 through 9.
NUL %UDLE $PSP SPACE00@%VPP‘%Wp+P
SOH $A
DC1 $Q!/A11AAQQa+Aq+Q
STX $B
DC2 $R“/B22BBRRb+Br+R
ETX $C
DC3 $S#/C33CCSSc+Cs+S
EOT $D
DC4 $T$/D44DDTTd+Dt+T
ENQ $E
NAK $U%/E55EEUUe+Eu+U
ACK $F
SYN $V&/F66FFVVf+Fv+V
BEL $G
ETB $W‘/G77GGWWg+Gw+W
BS $H
CAN $X(/H88HHXXh+Hx+X
HT $I
EM $Y)/I99IIYYi+Iy+Y
LF $J
SUB $Z*/J:/ZJJZZj+Jz+Z
VT $K
ESC %A+/K;%FKK[%Kk+K{%P
FF $L
FS %B,/L%INN^%Nn+N~%S
SI $O
US %E//O?%JOO_%Oo+ODEL %T
*  Full ASCII Off Full ASCII On 
						

							6 - 9
Code 39 Code Page
Code pages define the mapping of character codes to characters.  If the data 
received does not display with the proper characters, it may be because the bar 
code being scanned was created using a  code page that is different from the 
one the host program is expecting.  If this is the case, scan the bar code below, 
select the code page with which the bar codes were created from the chart, 
Code Page Mapping of Printed bar codeson page A-6, and scan the value and 
the SAVE bar code from the Programming Chart inside the back cover of this 
manual.  The data characters should then appear properly.
Interleaved 2 of 5
< Default All Interleaved 2 of 5 Settings >
Interleaved 2 of 5
Check Digit
No Check Digit indicates that the image scanner reads and transmits bar code 
data with or without a check digit.
When Check Digit is set to Validate, but Don’t Transmit, the unit only reads 
Interleaved 2 of 5 bar codes printed with a check digit, but will not transmit the 
check digit with the scanned data.  
Code 39 Code Page
*  On
Off 
						

							6 - 10
When Check Digit is set to Validate and Transmit, the image scanner only 
reads Interleaved 2 of 5 bar codes printed with a check digit, and will transmit 
this digit at the end of the scanned data.  
Default = No Check Digit.
Interleaved 2 of 5 Message Length
Scan the bar codes below to change the message length.  Refer to Message 
Lengthon page 6-2 for additional information.  Minimum and Maximum
lengths = 2-80.  Minimum Default = 4, Maximum Default = 80.
Validate, but Don’t Transmit * No Check Digit
Validate and Transmit
Minimum Message Length
Maximum Message Length