Honeywell 1900gsr 2 User Manual

CHAPTER
1
Xenon/Granit User Guide1
GET STARTED
About This Manual
This User’s Guide provides installation and programming instructions for the 
Xenon™ 1900 corded area-imaging scanners, the Xenon 1902 cordless area-imag-
ing scanners, the Granit 1910i and 1980i corded industrial scanners, and the 
Granit 1911i and 1981i cordless industrial scanners. Product specifications, 
dimensions, warranty, and customer support information are also included.
Honeywell bar code scanners are factory programmed for the...

2Xenon/Granit User Guide 1. Connect the appropriate interface cable to the device first, then to the com-
puter.
Corded Xenon Scanner 
USB Connection:
Corded Granit Scanner 
USB Connection: 

Xenon/Granit User Guide3 2. If you are connecting a Granit scanner, make sure the cable is pushed tightly 
into the scanner. Loosen the locking plate and slide it over the base of the cable 
connector to lock the cable in place. Tighten the screw.
Note:The power supply must be ordered separately, if needed.
3. If you are connecting a CCB01-010BT or CCB01-010BT-BF Base, make sure 
the cables are secured in the wireways in the bottom of the cordless base and 
the base sits flat on a horizontal surface. If...

4Xenon/Granit User Guide For additional USB programming and technical information, refer to “USB Applica-
tion Note,” available at www.honeywellaidc.com.
Connect with Keyboard Wedge
A scanner or cordless base can be connected between the keyboard and PC as a 
“keyboard wedge,” where the scanner provides data output that is similar to key-
board entries. 
Note:The Granit 1980i does not support the keyboard wedge interface.
The following is an example of a keyboard wedge connection:
1. Turn off power and...

Xenon/Granit User Guide5 3. If you are connecting a Granit scanner, make sure the cable is pushed tightly 
into the scanner. Loosen the locking plate and slide it over the base of the cable 
connector to lock the cable in place. Tighten the screw.
Note:The power supply must be ordered separately, if needed.
4. If you are connecting a CCB01-010BT or CCB01-010BT-BF Base, make sure 
the cables are secured in the wireways in the bottom of the cordless base and 
the base sits flat on a horizontal surface. If...

6Xenon/Granit User Guide The unit defaults to an IBM PC AT and compatibles keyboard wedge interface with 
a USA keyboard. A carriage return (CR) suffix is added to bar code data. 
Connect with RS232 Serial Port
1. Turn off power to the terminal/computer.
2. Connect the appropriate interface cable to the scanner.
Note:For the scanner or cordless base to work properly, you must have the correct cable for 
your type of terminal/computer.
Corded Xenon Scanner 
RS232 Serial Port 
Connection:
Corded Granit...

Xenon/Granit User Guide7 3. If you are connecting a Granit scanner, make sure the cable is pushed tightly 
into the scanner. Loosen the locking plate and slide it over the base of the cable 
connector to lock the cable in place. Tighten the screw.
Note:The power supply must be ordered separately, if needed.
4. If you are connecting a CCB01-010BTor CCB01-010BT-BF Base, make sure the 
cables are secured in the wireways in the bottom of the cordless base and the 
base sits flat on a horizontal surface. If...

8Xenon/Granit User Guide
Connect with RS485
A Xenon scanner or cordless base can be connected for an IBM POS terminal inter-
face. (This interface is not available in the Granit devices.)
1. Connect the appropriate interface cable to the device, then to the computer.
Note:The power supply must be ordered separately, if needed.
2. Make sure the cables are secured in the wireways in the bottom of the cordless 
base and the base sits flat on a horizontal surface.
3. Turn the terminal/computer power back on....

Xenon/Granit User Guide9
Mount a CCB01-010BT Charge Base
Mount a CCB02-100BT/CCB05-100BT Base
The CCB02-100BT or CCB05-100BT Base can be mounted on either a horizontal 
or vertical surface. The cables can be routed through either the top or the bottom 
of the base. 
The cables can be routed down through the bottom of the base, securing the 
cables in the wireways.
The cables can also be routed up through the top of the base, crossing them over 
and securing the cables in the wireways. 
When routing the...

10Xenon/Granit User Guide When mounted on a vertical surface, a locking system is used to secure the scan-
ner when it is in the stand. When mounted on a horizontal surface, the locking 
mechanism should be set to unlocked (pushed up). When mounted on a vertical 
surface, the locking mechanism should be set to locked (pushed down).
Use 30mm screws, appropriate for the mounting surface material, to mount the 
base securely.
 
Locked position 
for vertical mountUnlocked position 
for horizontal mount
2...