Honeywell 1900gsr 2 User Manual

Xenon/Granit User Guide 1416A code identifier for Code 128
9999 code length that must match for Code 128, 9999 = all lengths
42 start character match for Code 128, 42h = “B”
FF termination string for second code
69 code identifier for Code 93
9999 code length that must match for Code 93, 9999 = all lengths
43 start character match for Code 93, 43h = “C”
FF termination string for third code
To program the previous example using specific lengths, you would have to count 
any programmed prefixes, suffixes,...

142 Xenon/Granit User Guide
Partial Sequence
If an output sequence operation is terminated before all your output sequence cri-
teria are met, the bar code data acquired to that point is a “partial sequence.”  
Scan Discard Partial Sequence to discard partial sequences when the output 
sequence operation is terminated before completion. Scan Transmit Par tial 
Sequence to transmit partial sequences. (Any fields in the sequence where no data 
match occurred are skipped in the output.)
Require Output...

Xenon/Granit User Guide 143
Multiple Symbols
When this programming selection is turned On, it allows you to read multiple sym-
bols with a single pull of the scanner’s trigger. If you press and hold the trigger, 
aiming the scanner at a series of symbols, it reads unique symbols once, beeping 
(if turned on) for each read. If using a Granit scanner, the scanner also vibrates. The 
scanner attempts to find and decode new symbols as long as the trigger is pulled. 
When this programming selection is turned...

144 Xenon/Granit User Guide
Video Reverse
Video Reverse is used to allow the scanner to read bar codes that are inverted. The 
Video Reverse Off bar code below is an example of this type of bar code. Scan 
Video Reverse Only to read only inverted bar codes. Scan Video Reverse and 
Standard Bar Codes to read both types of codes. 
Note:After scanning Video Reverse Only, menu bar codes cannot be read. You must scan 
Video Reverse Off or Video Reverse and Standard Bar Codes in order to read menu 
bar codes....

Xenon/Granit User Guide 145
Working Orientation
Some bar codes are direction-sensitive. For example, KIX codes and OCR can mis-
read when scanned sideways or upside down. Use the working orientation settings 
if your direction-sensitive codes will not usually be presented upright to the scan-
ner. Default = Upright. 
Upright:
Vertical, Top to Bottom:
(Rotate CW 90°)
Upside Down:
Vertical, Bottom to Top:
(Rotate CCW 90°)
* Upright
Vertical, Bottom to Top
Upside Down
Vertical, Top to Bottom 

146 Xenon/Granit User Guide 

CHAPTER
6
Xenon/Granit User Guide 147
HEALTHCARE SETTINGS
The following settings have been developed to enhance scanning in a healthcare 
environment. These settings are only supported by the Xenon 1900h scanner and 
Xenon 1902h scanner and base. They allow you to set quickly configure streaming 
presentation, and to set the scanner and base to quiet modes for scanning that do 
not disturb resting patients.
Quiet Operations - Combination Codes
The following combination codes program your Xenon healthcare...

148 Xenon/Granit User Guide
Silent Mode with Long LED
Scan the following bar code to completely silence the Xenon 1900h scanner or 
Xenon 1902h scanner and base. The scanner beep, base beep, base and scanner 
power up beep, and scanner linking sounds are all silenced. When a bar code is 
scanned, the LED and aimer remain solidly lit for 1 second. Green indicates a good 
scan, red indicates a bad scan.
Very Low Beeper (Nighttime Mode)
The following bar code silences the base, and sets the scanner for a...

Xenon/Granit User Guide 149
Low Beeper (Daytime Mode)
The following bar code sets all sounds to on, but at a low volume. The scanner 
beep, base beep, base and scanner power up beep, and scanner linking sounds are 
all set to low volume. 
To reset your scanner and base to default sounds, refer to Reset the Custom 
Defaults (page 271).
Quiet Operations - LED and Volume Settings
If you have silenced or muted the scanner and base sounds, you may wish to adjust 
the visual (LED) indicators for Bluetooth...

150 Xenon/Granit User Guide
Number of LED Flashes
If you have silenced the scanner’s beeper, you may set the number of times the 
LED flashes when reading bar codes. Default = 1 LED Flash.
Note:If you have set LED Solid (No Flash) (page 151), to anything but Off, that setting will 
override the LED Flash settings. In that case, scan the LED Solid Off bar code to turn 
off this feature, then scan the LED Flash code you wish to use.
LED Flash Rate
If you have silenced the scanner’s beeper, you may set the...