Honeywell 1900gsr 2 User Manual

Xenon/Granit User Guide 121
Trigger Toggle Timeout
This sets the length of time the scanner stays in trigger toggle mode before revert-
ing to scan mode. After scanning the Trigger Toggle Timeout bar code, set the 
time-out duration (from 0 to 65 seconds) by scanning digits from the 
Programming Chart, beginning on page 353, then Save. Default = 5 seconds.
Note:If this is set to 0, you must repeat the toggle sequence to return to the default 
scanning mode. For example, if 2 quick trigger presses puts...

122 Xenon/Granit User Guideset to Off, the aimer does not turn on until the trigger is pulled. Use the following 
bar codes to set Motion Activation when using the scanner in trigger mode. Refer 
to Presentation Motion Activation on page 122 if you are setting Motion Activation 
when using the scanner in Presentation Mode.
 
Presentation Mode
Presentation Mode uses ambient light and scanner illumination to detect bar 
codes. When in Presentation Mode, the LEDs remain dim until a bar code is pre-
sented...

Xenon/Granit User Guide 123
Presentation LED Behavior after Decode
When a scanner is in presentation mode, the LED aimer dims 30 seconds after a 
bar code is decoded. If you wish to dim the LED aimer immediately after a bar code 
is decoded, scan the LEDs Off bar code, below. Default = LEDs On.
Presentation Sensitivity
Presentation Sensitivity is a numeric range that increases or decreases the scan-
ner's reaction time to bar code presentation. To set the sensitivity, scan the Sensi-
tivity bar code,...

124 Xenon/Granit User GuideIf a bar code is not touched by a predefined window, it will not be decoded or output 
by the scanner. If Presentation Centering is turned on by scanning Presentation 
Centering On, the scanner only reads codes that pass through the centering win-
dow you specify using the Top of Presentation Centering Window, Bottom of 
Presentation Centering Window, Left, and Right of Presentation Centering Win-
dow bar codes. 
In the example below, the white box is the centering window. The...

Xenon/Granit User Guide 125
In-Stand Sensor Mode
Note:The In-Stand Sensor feature only applies to Xenon 1900, 1900h, 1902, and 1902h 
products. It does not apply to the Xenon 1902g-BF or Granit products.
This feature senses when the scanner is removed from the stand and tells it to 
begin manual triggering. When Sensor On is enabled, the scanner defaults to 
Streaming Presentation Mode when it is in the stand, and to Manual Trigger Mode 
when it is removed from the stand. Default = Sensor On.
Note:If you...

126 Xenon/Granit User Guide
Poor Quality Codes
Poor Quality 1D Codes
This setting improves the scanner’s ability to read damaged or badly printed linear 
bar codes. When Poor Quality 1D Reading On is scanned, poor quality linear bar 
code reading is improved, but the scanner’s snappiness is decreased, making it 
less aggressive when reading good quality bar codes. This setting does not affect 
2D bar code reading. Default = Poor Quality 1D Reading Off.
Poor Quality PDF Codes
This setting improves the...

Xenon/Granit User Guide 127
Low Resolution PDF Codes
This setting improves the scanner’s ability to read low resolution PDF codes. When 
Low Resolution PDF Codes On is scanned, poor quality PDF code reading is 
improved, but the scanner’s snappiness is decreased, making it less aggressive 
when reading good quality bar codes. This setting does not affect 1D bar code 
reading. Default = Low Resolution PDF Codes Off.
CodeGate®
When CodeGate is On, the trigger is used to allow decoded data to be transmitted...

128 Xenon/Granit User GuideWhen using Preferred Symbology(page 5-137), a lower priority symbol must be 
centered on the aiming pattern to be read in Streaming Presentation Mode.
Note:If you are using a cordless charge base, it must have an external power supply 
plugged into the aux port for Streaming Presentation to work properly.
Streaming Presentation In-Stand
This option is available when using In-Stand Sensor Mode, page 125. You may pro-
gram a specific Streaming Presentation Mode for in-stand...

Xenon/Granit User Guide 129
Hands Free Time-Out
The Scan Stand and Presentation Modes are referred to as “hands free” modes. If 
the scanner’s trigger is pulled when using a hands free mode, the scanner changes 
to manual trigger mode. You can set the time the scanner should remain in manual 
trigger mode by setting the Hands Free Time-Out. Once the time-out value is 
reached, (if there have been no further trigger pulls) the scanner reverts to the 
original hands free mode. 
Scan the Hands Free Time-Out...

130 Xenon/Granit User Guide
User-Specified Reread Delay
If you want to set your own length for the reread delay, scan the bar code below, 
then set the delay (from 0-30,000 milliseconds) by scanning digits from the 
Programming Chart, beginning on page 353, then Save. 
2D Reread Delay
Sometimes 2D bar codes can take longer to read than other bar codes. If you wish 
to set a separate Reread Delay for 2D bar codes, scan one of the programming 
codes that follows. 2D Reread Delay Off indicates that the time...