Honeywell 1900gsr 2 User Manual

Xenon/Granit User Guide 101
Batch Mode Beep
When scanning in Inventory Batch Mode (page 101), the scanner beeps every time 
a bar code is scanned. When Batch Mode Beep is On, you will also hear a click when 
each bar code is sent to the host. If you do not want to hear these clicks, scan Batch 
Mode Beep Off. Default = Batch Mode Beep On.
Batch Mode Storage
When a scanner is storing data during a Batch Mode process, you can select 
whether the data is stored in Flash memory or in RAM. 
Flash Storage: The...

102 Xenon/Granit User Guide
Batch Mode Quantity
When in Batch Mode, you may wish to transmit the number of multiple bar codes 
scanned, rather than a single bar code multiple times. For example, if you scan 
three bar codes called XYZ with Batch Mode Quantity Off, when you transmit your 
data it will appear as XYZ three times. Using Batch Mode Quantity On and the 
Quantity Codes (page 103), you could output your data as “XYZ, 00003” instead.
Note:If you wish to format your output, for example, place a CR...

Xenon/Granit User Guide 103Example:Add a quantity of 1,500 for the last item scanned.
1. Scan the item's bar code. 
2. Scan the quantity 1 bar code.
3. Scan the quantity 5 bar code.
4. Scan the quantity 0 bar code.
5. Scan the quantity 0 bar code.
Example:Change a quantity of 103 to 10.
To correct an incorrect quantity, scan the quantity 0 bar code to replace the incor-
rect digits, then scan the correct quantity bar codes.
1. Scan the quantity 0 bar code to change the quantity to 1030.
2. Scan the...

104 Xenon/Granit User Guide
Batch Mode Output Order
When batch data is transmitted, select whether you want that data sent as FIFO 
(first-in first-out), or LIFO (last-in first-out). Default = Batch Mode FIFO.
Total Records
If you wish to output the total number of bar codes scanned when in Batch Mode, 
scan Total Records. 
Quantity Codes  (Continued)
6
7
8
9
* Batch Mode FIFO
Batch Mode LIFO
Total Records  

Xenon/Granit User Guide 105
Delete Last Code
If you want to delete the last bar code scanned when in Batch Mode, scan Delete 
Last Code.
Clear All Codes
If you want to clear the scanner’s buffer of all data accumulated in Batch Mode, 
scan Clear All Codes.
Transmit Records to Host
If you are operating in Inventory Batch Mode (see Inventory Batch Mode on page 
101), you must scan the following bar code to transmit all the stored data to the 
host system.
Batch Mode Transmit Delay
Sometimes when...

106 Xenon/Granit User Guide
Scanner Name
You may assign a name to each scanner you are using for identification purposes. 
The default name is in the format “ScannerName_Model_SN_ XXXXXXXXXX” Per-
form the rename operation using either the bar codes on page 107, or by sending 
the serial command :ScannerName:BT_NAMNewName. where ScannerName is 
the current name of the scanner, and NewName is the new name for the scanner. 
To rename scanners with sequential, numeric names, scan the bar codes below. 
Scan...

Xenon/Granit User Guide 107You may also scan the Scanner Name bar code below and scan a number for the 
scanner name. For example, if you wanted to name the linked scanner “312,” you 
would scan the bar code below, scan the 3, 1, and 2 bar codes on the Programming 
Chart, beginning on page 353, then Save. Scan the Reset bar code and wait for the 
scanner to relink to the base.  
Change the Scanner’s Bluetooth PIN Code 
Some devices require a PIN code as part of the Bluetooth security features. Your...

108 Xenon/Granit User Guide
Auto Reconnect Mode
Auto Reconnect controls whether or not the scanner automatically begins the 
relink process when a loss of connection is detected. When the Auto Reconnect On 
bar code is scanned, the scanner begins the relink process immediately, without 
user intervention. Default = Auto Reconnect On.
The table below shows the results of the Auto Reconnect On and Off settings: 
Maximum Link Attempts
The Maximum Link Attempts setting controls the number of times the...

Xenon/Granit User Guide 109number of attempts is reached, the scanner will not attempt to reconnect to a base. 
Pressing the trigger or placing the scanner in the base resets the counter and the 
scanner will again try to link. 
Scan the Maximum Link Attempts bar code, then scan the number of attempts for 
the setting (from 0-100) from theProgramming Chart, beginning on page 353, 
then Save. Default = 4.
Note:When Auto Reconnect Mode is On, setting Maximum Link Attempts to zero will cause 
the scanner to...

110 Xenon/Granit User Guidestops trying to connect to the base, but retains any bar codes that may have been 
saved in batch mode. After one hour, the scanner powers off and batch mode data 
is lost.
Example:Auto Reconnect Mode set to 0
Maximum Link Attempts set to 15
Other values at default setting
When the scanner goes out of range, no action is taken to relink. When the trigger 
is pulled, 15 attempts are made to link to the base. Each attempt consists of 
approximately 5 seconds of active time...