Honeywell 1900ghd-2 User Manual

8 - 23
UPC-E0 Addenda Separator
When this feature is On, there is a space between the data from the bar code and the data from the addenda.  When turned 
Off, there is no space.  Default = On.
UPC-E0 Check Digit
Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not.  Default = On.
UPC-E0 Leading Zero
This feature allows the transmission of a leading zero (0) at the beginning of scanned data.  To prevent transmission, scan 
Off.  Default = On.
UPC-E0...

8 - 24
UPC-E1
Most U.P.C. bar codes lead with the 0 number system.  For these codes, use UPC-E0 (page 8-22).  If you need to read codes 
that lead with the 1 number system, use the UPC-E1 On selection.  Default = Off.
EAN/JAN-13

EAN/JAN-13 On/Off
Convert UPC-A to EAN-13
When UPC-A Converted to EAN-13 is selected, UPC-A bar codes are converted to 13 digit EAN-13 codes by adding a 
zero to the front.  When Do not Convert UPC-A is selected, UPC-A codes are read as UPC-A.
5 Digit Addenda On
* 5 Digit...

8 - 25
EAN/JAN-13 Check Digit
This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not.  
Default = On.
EAN/JAN-13 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data.  Default = Off for both 2 Digit and 5 Digit 
Addenda.
EAN/JAN-13 Addenda Required
When Required is scanned, the scanner will only read EAN/JAN-13 bar codes that have addenda.  Default = Not Required.
* Do not Convert  UPC-A
*  On
Off
2 Digit...

8 - 26
EAN/JAN-13 Addenda Separator
When this feature is On, there is a space between the data from the bar code and the data from the addenda.  When turned 
Off, there is no space.  Default = On.
Note: If you want to enable or disable EAN13 with Extended Coupon Code, refer to UPC-A/EAN-13 with Extended Coupon 
Code (page 8-21).
ISBN Translate
When On is scanned, EAN-13 Bookland symbols are translated into their equivalent ISBN number format. Default = Off. 
*  Not Required
*  On
Off
On
*  Off 

8 - 27
EAN/JAN-8

EAN/JAN-8 On/Off
EAN/JAN-8 Check Digit
This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not.  
Default = On.
EAN/JAN-8 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data.  Default = Off for both 2 Digit and 5 Digit 
Addenda.
*  On
Off
*  On
Off
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On 

8 - 28
EAN/JAN-8 Addenda Required
When Required is scanned, the scanner will only read EAN/JAN-8 bar codes that have addenda.  Default = Not Required.
EAN/JAN-8 Addenda Separator
When this feature is On, there is a space between the data from the bar code and the data from the addenda.  When turned 
Off, there is no space.  Default = On.
* 5 Digit Addenda Off
Required
*  Not Required
*  On
Off 

8 - 29
MSI

MSI On/Off
MSI Check Character
Different types of check characters are used with MSI bar codes.  You can program the scanner to read MSI bar codes with 
Type 10 check characters.  Default = Validate Type 10, but Don’t Transmit.
When Check Character is set to Validate Type 10/11 and Transmit, the scanner will only read MSI bar codes printed with 
the specified type check character(s), and will transmit the character(s) at the end of the scanned data.
When Check Character is set to Validate...

8 - 30
MSI Message Length
Scan the bar codes below to change the message length.  Refer to Message Length Description (page 8-1) for additional 
information.  Minimum and Maximum lengths = 4-48.   Minimum Default = 4, Maximum Default = 48.
Validate Type 11 then 
Type 10 Character and Transmit
Disable MSI Check Characters
Minimum Message Length
Maximum Message Length 

8 - 31
GS1 DataBar Omnidirectional
< Default All GS1 DataBar Omnidirectional Settings >
GS1 DataBar Omnidirectional On/Off
GS1 DataBar Limited
< Default All GS1 DataBar Limited Settings >
GS1 DataBar Limited On/Off
* On
Off
* On
Off 

8 - 32
GS1 DataBar Expanded
< Default All GS1 DataBar Expanded Settings >
GS1 DataBar Expanded On/Off
GS1 DataBar Expanded Message Length
Scan the bar codes below to change the message length.  Refer to Message Length Description (page 8-1) for additional 
information.  Minimum and Maximum lengths = 4-74.   Minimum Default = 4, Maximum Default = 74.
Trioptic Code
Note: If you are going to scan Code 32 Pharmaceutical codes (page 8-5), Trioptic Code must be off.
Trioptic Code is used for labeling magnetic...