Honeywell 1250g2 Manual

							2 - 9
Ver i fon e® Ruby Terminal Default Settings
Scan the following Plug and Play code to program the scanner for a Verifone 
Ruby terminal.  This bar code sets the baud rate to 1200 bps and the data for-
mat to 8 data bits, Mark parity, 1 stop bit and RTS/CTS no timeout.  It also adds 
a line feed (LF) suffix and programs the following prefixes for each symbology:
Note: If you are having unexpected results with this programming code, scan 
the Activate Defaults bar code on page 8-4 first, then scan the 
programming bar code above.
Gilbarco® Terminal Default Settings
Scan the following Plug and Play code to program the scanner for a Gilbarco 
terminal.  This bar code sets the baud rate to 2400 bps and the data format to 7 
data bits, even parity, 2 stop bits.  It also adds a carriage return (CR) suffix and 
programs the following prefixes for each symbology:
Note: If you are having unexpected results with this programming code, scan 
the Activate Defaults bar code on page 8-4 first, then scan the 
programming bar code above.
SymbologyPrefix
UPC-A A
UPC-E A
EAN-8 FF
EAN-13 F
SymbologyPrefix
UPC-A A
UPC-E E0
EAN-8 FF
EAN-13 F
Verifone Ruby Settings
Gilbarco Settings 
						

							2 - 10
Honeywell Bioptic Aux Port Configuration
Scan the following Plug and Play code to program the scanner for a Honeywell 
bioptic scanner auxiliary port configuration.  This bar code sets the baud rate to 
38400 bps and the data format to 8 data bits, no parity, 1 stop bit.  Character 
RTS/CTS with timeout and 232 ACK/NAK are also enabled.  
Note: If you are having unexpected results with this programming code, scan 
the Activate Defaults bar code on page 8-4 first, then scan the 
programming bar code above.
Datalogic™ Magellan© Bioptic
Aux Port Configuration
Scan the following Plug and Play code to program the scanner for a Datalogic 
Magellan bioptic scanner auxiliary port configuration.  This bar code sets the 
baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit.  
Note: If you are having unexpected results with this programming code, scan 
the Activate Defaults bar code on page 8-4 first, then scan the 
programming bar code above.
NCR Bioptic Aux Port Configuration
Scan the following Plug and Play code to program the scanner for an NCR biop-
tic scanner auxiliary port configuration.  This bar code sets the baud rate to 
9600 bps and the data format to 7 data bits, Even parity, 1 stop bit and Message 
RTS/CTS with timeout.  The following prefixes are programmed for each sym-
bology:
SymbologyPrefixSymbologyPrefix
UPC-A A Code 39 B1
UPC-E E0 Interleaved 2 of 5 B2
EAN-8 FF All other bar 
codesB3
EAN-13 F
Honeywell Bioptic Settings
Datalogic Magellan Bioptic Settings 
						

							2 - 11
Note: If you are having unexpected results with this programming code, scan 
the Activate Defaults bar code on page 8-4 first, then scan the 
programming bar code above.
Wincor Nixdorf Terminal Default Settings
Scan the following Plug and Play code to program the scanner for a Wincor Nix-
dorf terminal.  This bar code sets the baud rate to 9600 bps and the data format 
to 8 data bits, no parity, 1 stop bit.  
Note: If you are having unexpected results with this programming code, scan 
the Activate Defaults bar code on page 8-4 first, then scan the 
programming bar code above.
NCR Bioptic Settings
Wincor Nixdorf Terminal Settings 
						

							2 - 12
Wincor Nixdorf Beetle™ 
Terminal Default Settings
Scan the following Plug and Play code to program the scanner for a Wincor Nix-
dorf Beetle terminal.  The following prefixes are programmed for each symbol-
ogy:
Note: If you are having unexpected results with this programming code, scan 
the Activate Defaults bar code on page 8-4 first, then scan the 
programming bar code above.
SymbologyPrefixSymbologyPrefix
Code 128 K EAN-13 A
Code 93 L GS1-128 P
Codabar N Interleaved 2 of 5 I
UPC-A A0 Plessey O
UPC-E C Straight  2 of 5 IATA H
EAN-8 B All other bar codes M
Wincor Nixdorf Beetle Settings 
						

							2 - 13
Wincor Nixdorf RS232 Mode A
Scan the following Plug and Play code to program the scanner for a Wincor Nix-
dorf RS232 Mode A terminal.  The following prefixes are programmed for each 
symbology:
SymbologyPrefixSymbologyPrefix
Code 128 K EAN-13 A
Code 93 L GS1-128 K
Codabar N Interleaved 2 of 5 I
UPC-A A0 Plessey O
UPC-E C Straight  2 of 5 IATA H
EAN-8 B GS1 DataBar E
All other bar codes M
Wincor Nixdorf RS232 Mode A 
Settings 
						

							2 - 14
Keyboard Country Layout
Scan the appropriate country code below to program the keyboard layout for 
your country or language. As a general rule, the following characters are sup-
ported, but need special care for countries other than the United States:
@  |  $  #  {  }  [  ]  =  /  ‘    <  >  ~   
* United States 
Albania
Azeri (Cyrillic)
Azeri (Latin)
Belarus
Belgium
Bosnia Arabic
Bulgaria (Cyrillic)Brazil (MS)
Brazil
Bulgaria (Latin) 
						

							2 - 15
Keyboard Country (continued)
Canada (French)
Canada (Multilingual)
Croatia
Czech
Czech (QWERTY)
Czech (QWERTZ) Canada (French legacy)
Denmark
Czech (Programmers)China
FaeroeseEstonia
Dutch (Netherlands) 
						

							2 - 16
Keyboard Country (continued)
Gaelic
Germany
Greek
Greek (220 Latin)
Greek (220)
Greek (319 Latin)
Greek (319) France
Greek (Latin)
Greek (MS)
Finland
Hungarian (101 key)Hebrew Greek (Polytonic) 
						

							2 - 17
Keyboard Country (continued)
Iceland
Ireland
Italy
Japan ASCII
Kazakh
Kyrgyz (Cyrillic)Hungary
Latin America
LatviaKorea
Lithuania (IBM) LithuaniaLatvia (QWERTY)Italian (142) 
						

							2 - 18
Keyboard Country (continued)
Malta
Mongolian (Cyrillic)
Norway
Poland
Polish (214)
Polish (Programmers)
Portugal Macedonia
Romania
Russia
SCSRussian (Typewriter) Russian (MS)