Hitachi Projector CP-X4022WN User Manual

61
OPTION menu
ItemDescription
LAMP TIME The lamp time is the usage time of the lamp, counted after the last 
resetting. It is shown in the OPTION menu.
Pressing the RESET button on the remote control or the ► button 
of the projector displays a dialog. 
To reset the lamp time, select the OK using the ► button.
CANCEL
 ð  OK
• Please reset the lamp time only when you have replaced the lamp, 
for a suitable indication about the lamp.
• 
For the lamp replacement, see the section Replacing the lamp ( 107)...

62
OPTION menu
ItemDescription
MY BUTTON This item is to assign one of the following functions to 
MY BUTTON 
1/2 on the remote control (
 6).
(1)   Use the ▲/▼ buttons on the MY BUTTON menu to select a MY 
BUTTON - (1/2) and press the ► or ENTER button to display the 
MY BUTTON setup dialog. 
(2)   Then using the ▲/▼/◄/► buttons sets one of the following 
functions to the chosen button. Press the ENTER or INPUT 
button to save the setting.
• COMPUTER IN1: Selects the input from COMPUTER IN1 port.
•...

63
OPTION menu
ItemDescription
MY BUTTON (continued )• ACTIVE IRIS: Changes the active iris mode.
• PICTURE MODE: Changes the PICTURE MODE (

36).
•  FILTER RESET: Displays the filter time reset confirmation dialogue  ( 61)
.
•    TEMPLATE: Makes the template pattern selected to the 
TEMPLATE item (
 57) appear or disappear.
•    AV MUTE: Turns the picture and audio on/off.
•   RESOLUTION: Turns on/off the RESOLUTION dialog (
 47).
•   MIC VOLUME: Turns on/off the MIC VOLUME dialog ( 52).
•   ECO...

64
OPTION menu
ItemDescription
SERVICE
(continued)
AUTO ADJUST
Using the ▲/▼ buttons to select one of the mode. When the 
DISABLE is selected, the automatic adjustment feature is disabled.
FINE  ó FAST 
ó DISABLE
   
FINE: Finer tuning including H.SIZE adjustment.
FAST :  Faster tuning, setting H.SIZE to prearranged data for the 
input signal.
• 
Depending on conditions, such as input image, signal cable to the 
projector, environment around the projector, etc., the automatic adjustment 
may not work...

65
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION
Selecting this item displays COMMUNICATION 
menu. 
In this menu, you can configure the serial 
communication settings of the projector using the 
CONTROL port.
• Select an item using the cursor buttons ▲/▼. 
Then pressing the ► button opens the submenu 
for the setting item you selected. Or, pressing 
the ◄ button instead of the ► button makes the 
menu back to the previous one without changing 
the setup. Each submenu can be operated as...

66
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION(continued)
COMMUNICATION TYPE
Select the communication type for transmission via 
the CONTROL port.
NETWORK BRIDGE: Select this type, if it is  required to control an external device as a 
network terminal, via this projector from the 
computer.
The CONTROL port doesn't accept RS-232C   
commands (Network Bridge Function  in the 
Network Guide)
OFF : Select this mode to receive RS-232C 
commands using the  CONTROL port. 
• OFF is...

67
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION (continued)
RESPONSE LIMIT TIME
Select the time period to wait for receiving 
response data from other device communicating by 
the NETWORK BRIDGE and the HALF-DUPLEX 
through the CONTROL port.
OFF  ó 1s 
ó 2s 
ó 3s
    
OFF : Select this mode if it is not required to check 
the responses from the device that the projector 
sends data to. In this mode, the projector can 
send out data from the computer continuously.
1s /2s /3s: Select the...

68
OPTION menu
ItemDescription
SERVICE
(continued)
CLONING(continued)
The following items are exempted.
OPTION: LAMP TIME, FILTER TIME, 
SERVICE(GHOST, 
COMMUNICATION(STACK))
NETWORK: WIRELESS AND WIRED SETUP (IP ADDRESS, SUBNET MASK, 
DEFAULT GATEWAY, DATE AND 
TIME), MY IMAGE, PRESENTATION
SECURITY: MY TEXT DISPLAY, STACK LOCK
• Operation is not available if SECURITY_
CLONNING LOCK is turned ON.
• The Screen_MyScreen can only be loaded.
CLONING load function on STANDBY MODE
• While the projector is in...

69
OPTION menu
ItemDescription
SERVICE
(continued)
CLONING(continued)
Load MyScreen data
•   Please save the image data as "pj_logo.bmp" or 
"pj_logo.gif" into USB memory.
•   Please note that the only compatible formats are 
as follows.
-File format Windows BMP    bit/pixel: 4/8/16/24/32bit
Compression format : 
Without compression/RLE
GIF
-Image size: more than 36x36, less than 1280x800
•   If two kinds of file format are saved, "pj_logo.
bmp" will be registered into MyScreen...

70
OPTION menu
ItemDescription
SERVICE
(continued) INFORMATION
Selecting this item displays a dialog titled “INPUT_INFORMATION”. 
It shows the information about the current input.
• The “FRAME LOCK” message on the dialog means the frame lock 
function is working. 
• The “SCART RGB” message means the COMPONENT ports 
is working as a SCART RGB input port. Please refer to the 
COMPONENT item in INPUT menu (

44).
• This item can't be selected for no signal and sync out.
• When the MY TEXT DISPLAY is...