Hitachi Projector CP-X4022WN User Manual

							61
OPTION menu
ItemDescription
LAMP TIME The lamp time is the usage time of the lamp, counted after the last 
resetting. It is shown in the OPTION menu.
Pressing the RESET button on the remote control or the ► button 
of the projector displays a dialog. 
To reset the lamp time, select the OK using the ► button.
CANCEL
 ð  OK
• Please reset the lamp time only when you have replaced the lamp, 
for a suitable indication about the lamp.
• 
For the lamp replacement, see the section Replacing the lamp ( 107)
.
FILTER TIME The filter time is the usage time of the air filter, counted after the last 
resetting. It is shown in the OPTION menu.
Pressing the RESET button on the remote control or the ► button 
of the projector displays a dialog. 
To reset the filter time, select the OK using the ► button.
CANCEL ð  OK
• 
Please reset the filter time only when you have cleaned or replaced 
the air filter, for a suitable indication about the air filter.
• For the air filter cleaning, see the section  Cleaning and replacing 
the air filter (
 109).
(continued on next page) 
						

							62
OPTION menu
ItemDescription
MY BUTTON This item is to assign one of the following functions to 
MY BUTTON 
1/2 on the remote control (
 6).
(1)   Use the ▲/▼ buttons on the MY BUTTON menu to select a MY 
BUTTON - (1/2) and press the ► or ENTER button to display the 
MY BUTTON setup dialog. 
(2)   Then using the ▲/▼/◄/► buttons sets one of the following 
functions to the chosen button. Press the ENTER or INPUT 
button to save the setting.
• COMPUTER IN1: Selects the input from COMPUTER IN1 port.
• COMPUTER IN2: Selects the input from COMPUTER IN2 port.
• LAN: Selects input from LAN port.
• USB TYPE A: Selects input from USB TYPE A port.
• USB TYPE B: Selects input from USB TYPE B port.
• HDMI: Selects input from HDMI port.
• COMPONENT: Selects the input from COMPONENT ports.
• S-VIDEO: Selects the input from S-VIDEO port.
• VIDEO: Selects the input from VIDEO port.
• 
SLIDESHOW: Selects the input from USB TYPE A, and starts a Slideshow.•   MY IMAGE: Displays the MY IMAGE menu ( 79).
•   MESSENGER: Turns the messenger text displayed on the screen on/off (Messenger Function in the Network Guide ). 
When there is no transferred text data to display, the message 
”NO MESSENGER DATA" appears.
•   INFORMATION: Displays SYSTEM_INFORMATION,  
INPUT_INFORMATION  (
70), WIRELESS INFORMATION 
( 75), WIRED INFORMATION (77) or nothing.
•    AUTO KEYSTONE : Performs automatic keystone distortion 
correction (
 48).
•   MY MEMORY: Loads one of adjustment data stored  (40). 
When more than one data are saved, the adjustment   
changes every time the  MY BUTTON is pressed.
When no data is saved in memory, the 
dialog "No saved data" appears.
When the current adjustment is not 
saved to memory, the dialog as shown in 
the right appears.
If you want to keep the current adjustment, please press   
the ► button to exit. Otherwise loading a data will overwrite the 
current adjusted condition.
(continued on next page)
(continued on next page) 
						

							63
OPTION menu
ItemDescription
MY BUTTON (continued )• ACTIVE IRIS: Changes the active iris mode.
• PICTURE MODE: Changes the PICTURE MODE (

36).
•  FILTER RESET: Displays the filter time reset confirmation dialogue  ( 61)
.
•    TEMPLATE: Makes the template pattern selected to the 
TEMPLATE item (
 57) appear or disappear.
•    AV MUTE: Turns the picture and audio on/off.
•   RESOLUTION: Turns on/off the RESOLUTION dialog (
 47).
•   MIC VOLUME: Turns on/off the MIC VOLUME dialog ( 52).
•   ECO MODE: Changes the ECO MODE ( 49).
•  SAVER MODE: Turns on/off the SAVER MODE  ( 49 ECO MODE).
MY SOURCE Using ▲/▼ buttons selects the picture input port to be selected with 
pressing the 
MY SOURCE/DOC.CAMERA  button on the remote 
control.
You can use this function not only for document cameras but also 
computers and other equipment.
COMPUTER IN1  ó COMPUTER IN2 
ó LAN 
ó USB TYPE A
VIDEO óS-VIDEO 
ó COMPONENT 
ó HDMI 
ó USB TYPE B
SERVICE Selecting this item displays the SERVICE 
menu.
Select an item using the ▲/▼ buttons, 
and press the ► button or the ENTER 
button on the remote control to execute 
the item.
ALTITUDE
Using the ▲/▼ buttons switches the rotation speed of the cooling fans. 
The HIGH is the mode for use at highlands etc. If the projector is used
at an altitude of about 1200 m (3937 feet) or higher, select HIGH. 
Otherwise, select NORMAL. Note that the projector is noisier when the 
HIGH is selected.
HIGH 
ó NORMAL
(continued on next page) 
						

							64
OPTION menu
ItemDescription
SERVICE
(continued)
AUTO ADJUST
Using the ▲/▼ buttons to select one of the mode. When the 
DISABLE is selected, the automatic adjustment feature is disabled.
FINE  ó FAST 
ó DISABLE
   
FINE: Finer tuning including H.SIZE adjustment.
FAST :  Faster tuning, setting H.SIZE to prearranged data for the 
input signal.
• 
Depending on conditions, such as input image, signal cable to the 
projector, environment around the projector, etc., the automatic adjustment 
may not work correctly.  In such a case, please choose DISABLE to 
disable the automatic adjustment, and make adjustment manually.
GHOST
Adjust the settings using the ▲/▼ buttons to eliminate ghosting.
FILTER MESSAGE
Use the ▲/▼ button to set the timer for notifying by the message 
when to replace the filter unit 
             100h  ó ·······
·· 
ó  5000h 
ó OFF
After choosing an item except OFF, the message “REMINDER *** 
HRS PASSED ....” will appear after the timer reaches the interval 
time set by this feature (
 113). 
When the OFF is chosen, the message will not appear. Utilize this 
feature to keep the air filter clean, setting the suitable time according 
to your environment of this projector.
• Please take care of the filter unit periodically, even if there is 
no message. If the air filter becomes to be blocked by dust or 
other matter, the internal temperature will rise, which could cause 
malfunction, or reduce the lifetime of the projector.
• Please be careful with the operating environment of the projector 
and the condition of the filter unit.
KEY LOCK
(1)   Use the ▲/▼ buttons to choose the operations control.
CONTROL PANEL  ó REMOTE CONTROL
(2)   
Use the ◄/► buttons to select ON or OFF.
ON 
ó OFF
Selecting ON in Step 2 locks the buttons except  STANDBY/ON on 
the operations control selected in Step 1. Selecting OFF releases 
the locked buttons on the operations control selected in Step 1.
• Please use this function to prevent tampering or accidental 
operation. 
(continued on next page) 
						

							65
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION
Selecting this item displays COMMUNICATION 
menu. 
In this menu, you can configure the serial 
communication settings of the projector using the 
CONTROL port.
• Select an item using the cursor buttons ▲/▼. 
Then pressing the ► button opens the submenu 
for the setting item you selected. Or, pressing 
the ◄ button instead of the ► button makes the 
menu back to the previous one without changing 
the setup. Each submenu can be operated as 
described above.
• When COMMUNICATION TYPE (
 66) is set to 
OFF, the other items in COMMUNICATION menu 
are invalid. 
• For the function of serial communication, refer to  
the Network Guide .
(continued on next page) 
						

							66
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION(continued)
COMMUNICATION TYPE
Select the communication type for transmission via 
the CONTROL port.
NETWORK BRIDGE: Select this type, if it is  required to control an external device as a 
network terminal, via this projector from the 
computer.
The CONTROL port doesn't accept RS-232C   
commands (Network Bridge Function  in the 
Network Guide)
OFF : Select this mode to receive RS-232C 
commands using the  CONTROL port. 
• OFF is selected as the default setting. 
• When you select the NETWORK BRIDGE, check 
the item, TRANSMISSION METHOD  (
below)
SERIAL SETTINGS
Select the serial communication condition for the 
CONTROL port. BAUD RATE 4800bps  ó 9600bps 
ó 19200bps 
ó 38400bps
      
 PARITY
NONE  ó ODD 
ó EVEN
    
• The BAUD RATE is fixed to 19200bps 
and PARITY is fixed NONE when the 
COMMUNICATION TYPE is set to OFF  (
above).
TRANSMISSION METHOD
Select the transmission method for communication 
by the NETWORK BRIDGE from the 
CONTROL 
port.
HALF-DUPLEX  ó FULL-DUPLEX
HALF-DUPLEX : This method lets the projector 
make two way communication, but only one 
direction, either transmitting or receiving data, is 
allowed at a time.
FULL-DUPLEX : This method lets the projector 
make two way communication, transmitting and 
receiving data at the same time.
• HALF-DUPLEX is selected as the default setting.
• If you select HALF-DUPLEX, check the setting of 
the item RESPONSE LIMIT TIME  (
67).
(continued on next page) 
						

							67
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION (continued)
RESPONSE LIMIT TIME
Select the time period to wait for receiving 
response data from other device communicating by 
the NETWORK BRIDGE and the HALF-DUPLEX 
through the CONTROL port.
OFF  ó 1s 
ó 2s 
ó 3s
    
OFF : Select this mode if it is not required to check 
the responses from the device that the projector 
sends data to. In this mode, the projector can 
send out data from the computer continuously.
1s /2s /3s: Select the time period to keep the  projector waiting for response from the device 
that the projector sends data to. While waiting the 
response, the projector does not send out any 
data from the CONTROL port.
• This menu is available only when the NETWORK 
BRIDGE is selected for the COMMUNICATION 
TYPE and the HALF-DUPLEX is selected for the 
TRANSMISSION METHOD  (
66).
• OFF is selected as the default setting.
STACK
Selecting this item displays the STACK menu. 
For more information, please see  Instant Stack 
Guide .
CLONING
The setttings of the projector can be coppied via USB 
memory.
SAVE:  Saves each settings of the projector to USB 
memory.
LOAD: 
Loads each settings of the projector from 
USB memory. Message will be displayed 
after loading, and power will turn off after five 
min. or by pressing ► button. (A message is 
displayed for a few seconds if loading fails.)
After saving / loading, you can remove the USB 
storage device.
(continued on next page) 
						

							68
OPTION menu
ItemDescription
SERVICE
(continued)
CLONING(continued)
The following items are exempted.
OPTION: LAMP TIME, FILTER TIME, 
SERVICE(GHOST, 
COMMUNICATION(STACK))
NETWORK: WIRELESS AND WIRED SETUP (IP ADDRESS, SUBNET MASK, 
DEFAULT GATEWAY, DATE AND 
TIME), MY IMAGE, PRESENTATION
SECURITY: MY TEXT DISPLAY, STACK LOCK
• Operation is not available if SECURITY_
CLONNING LOCK is turned ON.
• The Screen_MyScreen can only be loaded.
CLONING load function on STANDBY MODE
• While the projector is in STANDBY MODE, push 
the INPUT button of control panel together with  ► 
button, and then press ▲ button to start operating 
the CLONING load function.
• During loading process, the three indicators of 
control panel (POWER (orange), TEMP, LAMP) 
will remain on.
•    After the loading process, the three indicators 
(POWER (orange), TEMP, LAMP) will turn off. 
Then, you can remove the USB storage device.
•   If the loading fails, the three indicators (POWER 
(orange), TEMP, LAMP) will blink at the same 
time.
• CLONING is invalid with the following conditions.
- CLONING LOCK is turned ON. 
    With this condition, the three indicators (POWER 
(orange), TEMP, LAMP) will blink at approximately 
three seconds intervals.
- If the STANDBY MODE is set to SAVING.
-   If there is no USB memory inserted into USB 
TYPE A port.
-   If PIN LOCK or lock of TRANSITION DETECTOR 
is not being released.
-   If a system error occurs.
- If STACK MODE is not set to OFF. 
• Please operate one of the following after loading.
-   Press INPUT button and 
◄ button of the control 
panel  at the same time.
- Wait at least five min. after loading. 
-   Restart the projector after re-plugging the AC 
cable.
(continued on next page) 
						

							69
OPTION menu
ItemDescription
SERVICE
(continued)
CLONING(continued)
Load MyScreen data
•   Please save the image data as "pj_logo.bmp" or 
"pj_logo.gif" into USB memory.
•   Please note that the only compatible formats are 
as follows.
-File format Windows BMP    bit/pixel: 4/8/16/24/32bit
Compression format : 
Without compression/RLE
GIF
-Image size: more than 36x36, less than 1280x800
•   If two kinds of file format are saved, "pj_logo.
bmp" will be registered into MyScreen data.
•   If MyScreen LOCK or MyScreen PASSWORD 
is turned ON, the data of MyScreen cannot be 
loaded.
Setting the data
•   Operating the SAVE function under CLONING 
will name the file as "pj_data.bin" into the USB 
memory. Please do not attempt to change the file 
name or the folder structure.
•   If a file with the same name already exists, it will 
be overwritten by operating the SAVE function.
Loading function
•   Please note that saved data from other model 
cannot be loaded.
•   Please note that, if any of the following 
functions: MyScreen PASSWORD, PIN 
LOCK, TRANSITION DETECTOR, MY TEXT 
PASSWORD under SECURITY menu or 
MyScreen Lock under SCREEN menu is ON, the 
respective saved data cannot be loaded. 
•   Please note that the saved settings of 
KEYSTONE (SETUP menu) and PERFECT FIT 
(SETUP menu) and AUTO KEYSTONE (OPTION 
menu) cannot be loaded when TRANSITION 
DETECTOR (SECURITY menu) is ON.
•   Please note that the saved data of START UP 
and MyScreen Lock under SCREEN menu 
cannot be loaded if  MyScreen PASSWORD 
under SECURITY menu is ON.
•   Please note that the saved data of MY TEXT 
WRITING cannot be loaded if MY TEXT 
PASSWORD under SECURITY menu is ON.
(continued on next page) 
						

							70
OPTION menu
ItemDescription
SERVICE
(continued) INFORMATION
Selecting this item displays a dialog titled “INPUT_INFORMATION”. 
It shows the information about the current input.
• The “FRAME LOCK” message on the dialog means the frame lock 
function is working. 
• The “SCART RGB” message means the COMPONENT ports 
is working as a SCART RGB input port. Please refer to the 
COMPONENT item in INPUT menu (

44).
• This item can't be selected for no signal and sync out.
• When the MY TEXT DISPLAY is set to ON, the MY TEXT is 
displayed together with the input information in the   
INPUT_INFORMATION box (
 87).
FACTORY RESET
Selecting OK using the ► button performs this function. By this 
function, all the items in all of menus will collectively return to the 
initial setting. Note that the items LAMP TIME, FILTER TIME, 
LANGUAGE, FILTER MESSAGE, NETWORK and SECURITY 
settings are not reset. CANCEL  ð OK
Be sure to set ALTITUDE after resetting all the settings (
 63).