Hitachi Projector CP-X4022WN User Manual

							21
Power on/off
►A strong light is emitted when the projector’s power is on.  
Do not look into the lens of the projector or look inside of the projector through 
any of the projector’s openings.
►Do not touch around the lamp cover and the exhaust vents during use or just 
after use, since it is too hot. WARNING
1.Press the STANDBY/ON button on the projector or the remote control. 
 
The message “Power off?” will appear on the screen for about 5 seconds.
Turning off  the power
2.Press the STANDBY/ON button again while the message appears.   
The projector lamp will go off, and the POWER indicator will begin blinking in 
orange. Then POWER indicator will stop blinking and light in steady orange 
when the lamp cooling is complete (
114).
3.Attach the lens cover, after the  POWER indicator turns in steady orange.
Do not turn the projector on for about 10 minutes or more after turning it of f. 
Also, do not turn the projector off shortly after turning it on. Such operations might 
cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.
• Turn the power on/off in right order. Please power on the projector 
prior to the connected devices. 
• This projector has the function that can make the projector automatically turn 
on/off. Please refer to the DIRECT POWER ON (
59) and AUTO POWER 
OFF (
60) items of the OPTION menu. 
NOTE 
						

							22
Operating
1.
Adjusting the volume
Use the VOLUME +/VOLUME - buttons to adjust the volume.
A dialog will appear on the screen to aid you in adjusting the 
volume. If you do not do anything, the dialog will automatically 
disappear after a few seconds.
●  When 
 is selected for current picture input port, the volume 
adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu 
(
52).
●   Even if the projector is in the standby mode, the volume is adjustable when 
both of the following conditions are true:
-  An option other than 
 is selected for STANDBY in the AUDIO SOURCE 
item of the AUDIO menu (
52).
- 
NORMAL is selected in the STANDBY MODE item of the SETUP menu ( 50).
●   In the standby mode, the volume of the microphone is adjustable with the 
VOLUME +/- buttons on the remote control, in synchronization with the volume 
of the projector. 
1.Press MUTE button on the remote control. 
A dialog will appear on the screen indicating that you have muted 
the sound. 
To restore the sound, press the  MUTE, VOLUME + or 
VOLUME - button. Even if you do not do anything, the dialog 
will automatically disappear after a few seconds.
Temporarily muting the sound
●  When  is selected for current picture input port, the sound is always muted. 
Please see AUDIO SOURCE item of AUDIO menu (
52).
●  C.C. (Closed Caption) is automatically activated when sound is muted and an  input signal containing C.C. is received. This function is available only when 
the signal is NTSC for VIDEO or S-VIDEO, or 480i@60 for COMPONENT, 
COMPUTER IN1 or COMPUTER IN2, and when AUTO is selected for 
DISPLAY in the C.C. menu under the SCREEN menu (
58).
VOLUME +/- button
MUTE button
VIDEODOC.CAMERA
KEYSTONE
ASPECT SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
Operating 
						

							23
1.Press INPUT button on the projector. 
Each time you press the button, the projector switches its 
input port from the current port as below.
Selecting an input signal
●  While ON is selected for AUTO SEARCH item in OPTION menu (59), the 
projector will keep checking the ports in above order repeatedly till an input 
signal is detected.
● It may take several seconds to project the images from the USB TYPE B port.
               COMPUTER IN1  COMPUTER IN2  LAN 
    VIDEO                                                            USB  TYPE A
    S-VIDEO                                                        USB  TYPE B
                
   COMPONENT         HDMI  
1.Press VIDEO button on the remote control. 
Each time you press the button, the projector switches its 
input port from the current port as below.
●  While ON is selected for AUTO SEARCH item in OPTION menu,  the projector will keep checking every port sequentially till an input signal 
is detected (
59). If  VIDEO button is pressed when  COMPUTER IN1, 
COMPUTER IN2, LAN, USB TYPE A or USB TYPE B port is selected, the 
projector will check  HDMI port fi rst.
VIDEO button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
1.Press COMPUTER button on the remote control. 
Each time you press the button, the projector switches its 
input port from the current port as below.
●  While ON is selected for AUTO SEARCH item in OPTION menu, the 
projector will keep checking every port sequentially till an input signal is detected 
(
59). If COMPUTER button is pressed when VIDEO, S-VIDEO, COMPONENT 
or HDMI port is selected, the projector will check COMPUTER IN1 port fi rst.
●   It may take several seconds to project the images from the USB TYPE B port.
COMPUTER button
VIDEODOC.CAMERA
KEYSTONE
ASPECT SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
         COMPUTER IN1  COMPUTER IN2  LAN
               USB TYPE B        USB TYPE A
        HDMI 
 COMPONENT  S-VIDEO   VIDEO
Operating
INPUT 
button 
						

							24
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
MY SOURCE / 
DOC. CAMERA button
1.Press the MY SOURCE / DOC. CAMERA button on 
the remote control. The input signal will be changed 
into the signal you set as MY SOURCE (
63).
●  This function also can use for document camera. Select the  input port that connected the document camera.
Operating
1.Press SEARCH  button on the remote control.
The projector will start to check its input ports as below in 
order to fi nd any input signals.
When input signal is detected, the projector will stop 
searching and display the image. If no signal is found, 
the projector will return to the state selected before the 
operation.
Searching an input signal
●  While ON is selected for AUTO SEARCH item in OPTION menu (59), the 
projector will keep checking the ports in above order repeatedly till an input 
signal is detected.
●  
It may take several seconds to project the images from the USB TYPE B port.
SEARCH  button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
               COMPUTER IN1  COMPUTER IN2  LAN 
    VIDEO                                                            USB  TYPE A
    S-VIDEO                                                        USB  TYPE B
                
        COMPONENT      HDMI  
Selecting an input signal(continued) 
						

							25
Operating
Selecting an aspect ratio
● ASPECT button does not work when no proper signal is inputted.
● NORMAL mode keeps the original aspect ratio setting.
●  The display will be dark for a split second while switching the Aspect, but this is not a malfunction.
  For a computer signal
CP-X4022WN/CP-X5022WN:
NORMAL   4:3   16:9   16:10
       
CP-WX4022WN : 
NORMAL   4:3   16:9   16:10   NATIVE
   For a video signal, s-video signal or component video signal
CP-X4022WN/CP-X5022WN:
 4:3    16:9   14:9
  
CP-WX4022WN: 
4:3   16:9   16:10   14:9  NATIVE
  For an input signal from the LAN, USB TYPE A or USB TYPE B port, or  if there is no signal 
CP-X4022WN/CP-X5022WN: 4:3 (fi xed)
CP-WX4022WN : 16:10 (fi xed)
1.Press ASPECT button on the remote control.  
Each time you press the button, the projector switches the 
mode for aspect ratio in turn. ASPECT button
  For an HDMITM signal
CP-X4022WN/CP-X5022WN:
 NORMAL    4:3   16:9   16:10   14:9
CP-WX4022WN: 
NORMAL   4:3   16:9   16:10   14:9   NATIVE
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER 
						

							26
Operating
Adjusting the projector’s elevator
When the place to put the projector is slightly uneven 
to the left or right, use the elevator feet to place the 
projector horizontally. 
Using the feet can also tilt the projector in order to 
project at a suitable angle to the screen, elevating the 
front side of the projector within 12 degrees.
This projector has 2 elevator feet and 2 elevator buttons. 
An elevator foot is adjustable while pushing the elevator 
button on the same side as it.
To loose an 
elevator foot, push 
the elevator button 
on the same side 
as it.
To fi nely 
adjust, twist 
the foot.1. 
Holding the projector, push the elevator buttons to 
loose the elevator feet.
2. 
Position the front side of the projector to the desired 
height.
3. 
Release the elevator buttons in order to lock the 
elevator feet.
4. 
After making sure that the elevator feet are locked, 
put the projector down gently.
5. 
If necessary, the elevator feet can be manually   
twisted to make more precise adjustments. Hold the 
projector when twisting the feet.
►Do not handle the elevator buttons without holding the 
projector, since the projector may drop down.
►Do not tilt the projector other than elevating its front within 12 degrees using 
the adjuster feet. A tilt of the projector exceeding the restriction could cause 
malfunction or shortening the lifetime of consumables, or the projector itself. CAUTION 
						

							27
Operating
NOTE
Adjusting the lens 
1. 
Use the ZOOM ring to adjust the screen 
size.
2. 
Use the FOCUS ring to focus the picture.
3. 
Turn the VERTICAL adjuster fully counter 
clockwise. Then turn it clockwise and adjust 
the vertical lens position upward.
4. 
Turn the LOCK counter clockwise to loosen 
the lock of the HORIZONTAL adjuster.
5. 
Turn the HORIZONTAL adjuster clockwise 
or counter clockwise to adjust the horizontal 
lens position.
LOCK
FOCUS ring
ZOOM  ring
LOCK 
(Horizontal
adjuster lock)
HORIZONTAL 
adjuster
VERTICAL 
adjuster
6. 
Turn the LOCK fully clockwise to tighten it and lock the horizontal lens 
position.
7. 
Use the FOCUS ring to focus the picture.
►Operate the lens adjusters gently as the lens may malfunction 
when subjected to shocks. It may need more strength to turn the adjusters near 
the adjustment limits. Be careful not to apply too much strength. CAUTION
• Use a hexagon wrench to turn the  VERTICAL, HORIZONTAL 
adjusters and  LOCK. If you do not have a hexagon wrench, you can use a 
fl athead screwdriver with more careful handling. • Use the LOCK so that the lens does not shift from the adjusted horizontal 
lens position. Adjusting the vertical lens position may shift the horizontal lens 
position. This projector is not equipped with a lock for vertical lens position. • When the vertical lens shift is adjusted, it is recommended to shift the picture 
upward.
VERTICAL 
  CP-WX4022WN VERTICAL 
  CP-X4022WN
  CP-X5022WN
HORIZONTAL
h
h
w
h
/5
h/4 w
/10
w /10 
						

							28
Operating
1.Press POSITION button on the remote control when no menu is 
indicated.
The “POSITION” indication will appear on the screen.
Adjusting the position
2.Use the ▲/▼/◄/► cursor buttons to adjust the picture position.
When you want to reset the operation, press  RESET button on 
the remote control during the operation.
To complete this operation, press POSITION  button again. Even if 
you do not do anything, the dialog will automatically disappear 
after a few seconds.
●  
When this function is performed on a video signal or an s-video signal, some image 
such as an extra-line may appear at outside of the picture.
●  When this function is performed on a video signal or s-video signal, the range of  this adjustment depends on OVER SCAN in IMAGE menu  (
42) setting. It is not 
possible to adjust when OVER SCAN is set to 10.
●  If  POSITION button is pressed when a menu is indicated on screen, the displayed 
picture does not move its position but the menu does.
●  This function is unavailable for a signal from the  LAN, USB TYPE A, USB TYPE B 
or HDMI port.
1.Press AUTO button on the remote control. 
Pressing this button performs the following.
Using the automatic adjustment feature
   For a computer signal
The vertical position, the horizontal position and the horizontal 
phase will be automatically adjusted. 
Make sure that the application window is set to its maximum size 
prior to attempting to use this feature. A dark picture may still be 
incorrectly adjusted. Use a bright picture when adjusting.
   For a video signal and s-video signal
The video format best suited for the respective input signal will be selected 
automatically. This function is available only when the AUTO is selected for 
the VIDEO FORMAT item in the INPUT menu (
45). The vertical position and 
horizontal position will be automatically set to the default.
●  The automatic adjustment operation requires approx. 10 seconds. Also please  note that it may not function correctly with some input. 
●  When this function is performed for a video signal, a certain extra such as a line  may appear outside a picture.
●  When this function is performed for a computer signal, a black frame may be  displayed on the edge of the screen, depending on the computer model. 
●  
The items adjusted by this function may vary when the FINE or DISABLE is selected 
for the AUTO ADJUST item of the SERVICE item in the OPTION menu (
64).
POSITION  button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
AUTO button
  
For a component video signal 
The vertical position and horizontal position will be automatically set to the default. 
The horizontal phase will be automatically adjusted.
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER 
						

							29
AUTO:  performs the automatic vertical keystone correction. (
48)
MANUAL:   allows you to adjust the vertical and horizontal  keystone.
PERFECT FIT :   
allows you to adjust each of the screen 
corners and sides to correct the 
distortion.
• The menu or dialog will automatically disappear after several seconds 
of inactivity. Press the KEYSTONE button again, or point the cursor at EXIT in 
the dialog and press the ►or  ENTER button to end the operation and close the 
menu or dialog. 
• When the screen is adjusted by PERFECT FIT, neither AUTO nor MANUAL is 
selectable. If you wish to use these functions, refer to step 3 in the PERFECT  
FIT item to initialize the adjustment of PERFECT FIT.
• When TRANSITION DETECTOR is ON, these functions are not available 
(
85). 
NOTE
• When the projector is in one of the following conditions, the automatic 
vertical keystone correction feature may not work correctly or at all.
-  REAR / CEILING or FRONT / CEILING is selected for the INSTALLATION  item in the SETUP menu, and the projector screen is slanted or tilted down-
wards.
- The ZOOM adjustment is not set to the full WIDE (wide-angle focus).
- The projector is nearly horizontal (about ±4°).
- The projector is inclined at about ±40 degrees or over.
• When the horizontal lens shift is not set to the center, this function may not 
work well. NOTE
To correct the distortion of projected screen, you can select 
one of three options, AUTO, MANUAL and PERFECT FIT. 
First press the KEYSTONE button to display the KEYSTONE 
menu, and point at one of items with the ▲/▼ buttons.
Correcting the distortion 
Then  follow  the  procedure  shown  below  for  the  item 
you selected. 
  
 AUTO:
When AUTO is pointed at, pressing the ► or ENTER button performs 
automatic vertical keystone correction. 
Operating
KEYSTONE button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER 
						

							30
   PERFECT FIT: 
When PERFECT FIT is pointed at, pressing the 
► or ENTER button displays the KEYSTONE_
PERFECT FIT dialog.
This projector is equipped with a test pattern for 
PERFECT FIT. Select the test pattern icon 
 
shown in the lower left of the dialog with the ◄/▼ 
buttons. When you press the ENTER or INPUT 
button, the test pattern appears or disappears.
1.  If it is necessary to initialize the current 
adjustment, point at RESET in the dialog 
with the RESET button, and press the ENTER or 
INPUT button.
2.  Select one of the corners or sides to be 
adjusted with the ▲/▼/◄/► buttons and 
press the ENTER or INPUT button. 
    MANUAL:
 
When MANUAL is pointed at, pressing the ► or 
ENTER button displays the KEYSTONE_MANUAL 
dialog.
1. 
Select the vertical or horizontal keystone ( / ) 
with the ▲/▼ buttons.
2. 
Use the ◄/► buttons to adjust the keystone distortion.  
Correcting the distortion (continued)
(continued on next page)
• When the zoom adjustment is set to the TELE (telephoto focus), this 
function may be excessive. This function should be used when the zoom ad -
justment is set to the full WIDE (wide-angle focus) whenever possible.
• When the horizontal lens shift is not set to the center, this function may not 
work well.
• Point at RETURN in the dialog with the ▲/▼ buttons and press ◄ or ENTER 
button to return to the KEYSTONE menu. NOTE
Operating