Hitachi Projector CP-X4022WN User Manual

21
Power on/off
►A strong light is emitted when the projector’s power is on.  
Do not look into the lens of the projector or look inside of the projector through 
any of the projector’s openings.
►Do not touch around the lamp cover and the exhaust vents during use or just 
after use, since it is too hot. WARNING
1.Press the STANDBY/ON button on the projector or the remote control. 
 
The message “Power off?” will appear on the screen for about 5 seconds.
Turning off  the power
2.Press the STANDBY/ON...

22
Operating
1.
Adjusting the volume
Use the VOLUME +/VOLUME - buttons to adjust the volume.
A dialog will appear on the screen to aid you in adjusting the 
volume. If you do not do anything, the dialog will automatically 
disappear after a few seconds.
●  When 
 is selected for current picture input port, the volume 
adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu 
(
52).
●   Even if the projector is in the standby mode, the volume is adjustable when 
both of the following conditions...

23
1.Press INPUT button on the projector. 
Each time you press the button, the projector switches its 
input port from the current port as below.
Selecting an input signal
●  While ON is selected for AUTO SEARCH item in OPTION menu (59), the 
projector will keep checking the ports in above order repeatedly till an input 
signal is detected.
● It may take several seconds to project the images from the USB TYPE B port.
               COMPUTER IN1  COMPUTER IN2  LAN 
    VIDEO...

24
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
MY SOURCE / 
DOC. CAMERA button
1.Press the MY SOURCE / DOC. CAMERA button on 
the remote control. The input signal will be changed 
into the signal you set as MY SOURCE (
63).
●  This function also can use for document camera. Select the  input port that connected the document camera.
Operating
1.Press SEARCH  button on the remote control.
The...

25
Operating
Selecting an aspect ratio
● ASPECT button does not work when no proper signal is inputted.
● NORMAL mode keeps the original aspect ratio setting.
●  The display will be dark for a split second while switching the Aspect, but this is not a malfunction.
  For a computer signal
CP-X4022WN/CP-X5022WN:
NORMAL   4:3   16:9   16:10
       
CP-WX4022WN : 
NORMAL   4:3   16:9   16:10   NATIVE
   For a video signal, s-video signal or component video signal
CP-X4022WN/CP-X5022WN:
 4:3    16:9...

26
Operating
Adjusting the projector’s elevator
When the place to put the projector is slightly uneven 
to the left or right, use the elevator feet to place the 
projector horizontally. 
Using the feet can also tilt the projector in order to 
project at a suitable angle to the screen, elevating the 
front side of the projector within 12 degrees.
This projector has 2 elevator feet and 2 elevator buttons. 
An elevator foot is adjustable while pushing the elevator 
button on the same side as it.
To loose an...

27
Operating
NOTE
Adjusting the lens 
1. 
Use the ZOOM ring to adjust the screen 
size.
2. 
Use the FOCUS ring to focus the picture.
3. 
Turn the VERTICAL adjuster fully counter 
clockwise. Then turn it clockwise and adjust 
the vertical lens position upward.
4. 
Turn the LOCK counter clockwise to loosen 
the lock of the HORIZONTAL adjuster.
5. 
Turn the HORIZONTAL adjuster clockwise 
or counter clockwise to adjust the horizontal 
lens position.
LOCK
FOCUS ring
ZOOM  ring
LOCK 
(Horizontal
adjuster...

28
Operating
1.Press POSITION button on the remote control when no menu is 
indicated.
The “POSITION” indication will appear on the screen.
Adjusting the position
2.Use the ▲/▼/◄/► cursor buttons to adjust the picture position.
When you want to reset the operation, press  RESET button on 
the remote control during the operation.
To complete this operation, press POSITION  button again. Even if 
you do not do anything, the dialog will automatically disappear 
after a few seconds.
●  
When this function is...

29
AUTO:  performs the automatic vertical keystone correction. (
48)
MANUAL:   allows you to adjust the vertical and horizontal  keystone.
PERFECT FIT :   
allows you to adjust each of the screen 
corners and sides to correct the 
distortion.
• The menu or dialog will automatically disappear after several seconds 
of inactivity. Press the KEYSTONE button again, or point the cursor at EXIT in 
the dialog and press the ►or  ENTER button to end the operation and close the 
menu or dialog. 
• When the...

30
   PERFECT FIT: 
When PERFECT FIT is pointed at, pressing the 
► or ENTER button displays the KEYSTONE_
PERFECT FIT dialog.
This projector is equipped with a test pattern for 
PERFECT FIT. Select the test pattern icon 
 
shown in the lower left of the dialog with the ◄/▼ 
buttons. When you press the ENTER or INPUT 
button, the test pattern appears or disappears.
1.  If it is necessary to initialize the current 
adjustment, point at RESET in the dialog 
with the RESET button, and press the ENTER or...