Hitachi Projector CP-WU8461 User Manual

31
Operating
• The projector may ignore operation by buttons while moving the lens.
• You can perform the LOAD function using LENS MEMORY button.NOTE Adjusting the lens (continued)
This projector is equipped with memory functions for the 
lens adjustments (LENS SHIFT and LENS TYPE). Up 
to 3 sets of adjustments can be stored.
To utilize the lens memory feature, press the POSITION 
or FUNCTION button while the LENS SHIFT dialog is 
displayed. Then the LENS MEMORY dialog will ap-
pear. The current lens...

32
Operating
1.
Press POSITION button on the remote control when no menu is indicated. 
The “POSITION” indication will appear on the screen.
Adjusting the position
2.
Use the ▲/▼/◄/► cursor buttons to adjust the picture 
position.
When you want to reset the operation, press RESET 
button on the remote control during the operation.
To complete this operation, press POSITION button again. Even if you do not do 
anything, the dialog will automatically disappear after a few seconds.
1.
Press AUTO button on...

33
Operating
AUTO:  performs the automatic vertical keystone 
correction. (
57)
MANUAL:   allows you to adjust the vertical and horizontal 
keystone.
PERFECT FIT:   
allows you to adjust each of the screen 
corners to correct the distortion.
• The menu or dialog will automatically disappear after several seconds 
of inactivity. Press the KEYSTONE button again, or point the cursor at EXIT in 
the dialog and press the ►or ENTER button to end the operation and close the 
menu or dialog. 
• When the screen...

34
Operating
   PERFECT FIT: 
When PERFECT FIT is pointed at, pressing the 
► or ENTER button displays the KEYSTONE_
PERFECT FIT dialog.
This projector is equipped with a test pattern for 
PERFECT FIT. Select the test pattern icon 
 
shown in the lower left of the dialog with the ◄/▼ 
buttons. When you press the ENTER or INPUT 
button, the test pattern appears or disappears.
1.
 If it is necessary to initialize the current  
  adjustment, point at RESET in the dialog with the RESET button, and 
press...

35
Operating
Correcting the distortion (continued)
4. This projector is equipped with a memory feature for PERFECT FIT 
adjustment. Up to 3 sets of adjustments can be stored.
●  SAVE:  
To store the current PERFECT FIT adjustment, select one of the SAVE 
icons 
 numbered 1 to 3 (number of the memory) with the ◄ /▲/▼ buttons 
and press the ENTER or INPUT button.  
Remember that the current data being stored of a memory will be lost by 
saving new data into the memory.
●  LOAD:  
To recall stored...

36
Operating
1.
Using the magnify feature
2.
3.
4.
Press the MAGNIFY ON button on the remote 
control.  
The picture will be magnified, and the MAGNIFY 
dialog will appear on the screen. When the 
MAGNIFY ON button is pressed for the first time 
after the projector is turned on, the picture will be 
zoomed by 1.5 times. On the dialog, triangle marks 
to show each direction will be displayed.
The display magnification of the projector switches in order 
with every press of the MAGNIFY ON button.
  For...

37
Operating
1.Press the SHADE button on the control panel.
The mechanical lens shade closes and the 
screen turns to black. The SHADE indicator on 
the projector blinks in yellow while the shade is 
closed.  
To open the shade and restore the screen, press 
the SHADE button again.
Temporarily shading the screen
• The projector will turn off automatically when the time set up by the 
SHADE TIMER passes 
(70).
• When turning off the power by the normal procedure, the lens shade opens 
automatically. If...

38
Operating
The PbyP / PinP is a function for displaying two different picture signals on a 
screen that is separated into main and sub areas for each signal. 
PbyP (Picture by Picture) / PinP (Picture in Picture)
PbyP 
button
• If the LAN or USB TYPE A / B port is selected when the PbyP button 
is pressed, input from other port is displayed on the main area.
• When in the PbyP / PinP mode, use the MENU button on the remote control 
or ▲/▼ buttons on the control panel to display the OSD menu.
• 
There...

39
Operating
PbyP (Picture by Picture) / PinP (Picture in Picture) (continued)
The position of the main area can be toggled with the ◄/► buttons when the 
setting information is displayed on the screen. The yellow frame and the audio 
mark will move together with it.   Changing the main area
main 
areasub 
areamain 
area sub 
area
The setting information will be appeared for several seconds when the PbyP / 
PinP function is started. Displays the input information for each area. A yellow 
frame around...

40
Operating
Press any button to select an input port on the remote control or press the 
INPUT button on the control panel. A dialog box to select the input signal for 
the main area will be displayed. Choose a signal using the ▲/▼ buttons. To 
change the signal in the sub area, switch temporarily across to the main area 
with the ◄/► buttons. 
Displaying the same signal on the both areas is not allowed. Refer to the table 
for details on available input signal combinations. Any combinations marked...