Hitachi Projector CP-WU8461 User Manual

11
Setting up
Connecting with your devices (continued)
• Before connecting the projector to a computer, consult the computer’s 
manual and check the compatibility of the signal level, the synchronization 
methods and the display resolution output to the projector.
- 
 Some signal may need an adapter to input this projector.
- 
 Some computers have multiple screen display modes that may include some 
signals which are not supported by this projector.
- 
  Although the projector can display signals with a...

12
Setting up
Connecting with your devices (continued)
(continued on next page)
• If an oversized USB storage device blocks the LAN port, use only 
the further USB TYPE A port from the LAN port or a USB extension cable to 
connect the USB storage device.NOTE
► Before connecting the projector to a network system be sure 
to obtain the consent of the administrator of the network.
►
Do not connect the LAN port to any network that might have the excessive voltage.
►The designated USB wireless adapter that is...

13
Setting up
Connecting with your devices (continued)
(continued on next page)
fb`‘ƒrrk
VCR/DVD/
Blu-ray DiscTM 
player (
27) (27)
(27) (
60)
(27, 55)
• HDBaseT is a technology to transmit image, sound, ethernet or serial control 
signal via LAN cable.
• Please go to the following URL regarding the device of other company that 
supports HDBaseT and has been confi rmed compatible with this projector.
http://www.hitachi.co.jp/proj/
LAN or HDBaseT input port can be selected as ethernet signal...

14
Setting up
• The HDMI ports of this model are compatible with HDCP (High-band-
width Digital Content Protection) and therefore capable of displaying video 
signals from HDCP compatible DVD players or the like.
-  The HDMI ports support the following signals:
Video signal :  480i@60, 480p@60, 576i@50, 576p@50, 720p@50/60, 
1080i@50/60, 1080p@50/60
Audio signal :  Format Linear PCM 
Sampling frequency 48kHz / 44.1kHz / 32kHz
 
-  This projector can be connected with another equipment that has HDMI
TM...

15
To get together the signal cables and 
prevent them from coming off, fasten them to 
the projector using a commercially available 
plastic cable tie. Use a cable tie of size 
2.0x5.0mm or smaller. It is recommended 
to curl the end of the tie slightly before you 
thread it to the tie holder to enable it to get 
through easily.
Connecting with your devices (continued)
• To use a wired remote control, connect a wired remote control to the 
REMOTE CONROL IN port. You can also connect another projector to...

16
Using the security bar and slot
A commercially available anti-theft chain or 
wire can be attached to the security bar on 
the projector. Refer to the fi gure to choose 
an anti-theft chain or wire.
Also this product has the security slot for 
the Kensington lock. 
For details, see the manual of the security 
tool.
When using the USB wireless adapter, be 
sure to connect the adapter to the further 
USB TYPE A port from the LAN port and 
use the supplied adapter cover.
1. Loosen the screw (marked with...

17
Setting up
Connecting to a power supply
1.Put the connector of the power cord into the 
AC (AC inlet) of the projector.
2.Firmly plug the power cord’s plug into the 
outlet. In a couple of seconds after the power 
supply connection, the POWER indicator will 
light up in steady orange.
►Do not connect the projector to a power supply while no lens 
unit is attached to it.
►Please use extra caution when connecting the power cord, as incorrect or 
faulty connections may result in fi re and/or electrical...

18
Remote control
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote 
control starts to malfunction, try to replace the batteries. If you will not use the 
remote control for long period, remove the batteries from the remote control and 
store them in a safe place.
1.Holding the hook part of the battery 
cover, remove it.
2.Align and insert the two AA batteries 
(HITACHI MAXELL, Part No.LR6 or R6P) 
according to their plus and minus terminals 
as...

19
Remote control
About the remote control signal
The remote control works with the 
projector’s remote sensor. This projector 
has two remote sensors on the front and 
back sides.
The sensors can sense signals within 
the following range:
60 degrees (30 degrees to the left and right of the 
sensor) within 3 meters about.
• You can deactivate one of the sensors using the REMOTE RECEIV. 
item in the SERVICE menu of the OPTION menu (
75).
• The remote control signal reflected in the screen or the like may...

20
Using as a simple PC mouse & keyboard
The accessory remote control works as a simple 
mouse and keyboard of the computer, when the 
projector’s USB TYPE B port and the computer’s 
type A USB port are connected and MOUSE is 
selected for the USB TYPE B item in the OPTION 
menu (
71).
(1) PAGE UP key: Press PAGE UP button.
(2) PAGE DOWN key: Press PAGE DOWN button.
(3) Mouse left button: Press ENTER button.
(4) Move pointer:  Use the cursor buttons 
▲, ▼, ◄ and ►.
(5) ESC key: Press ESC button.
(6)...