Hitachi Projector CP-D27WN User Manual

41
INPUT menu
ItemDescription
COMPUTER IN The computer input signal type for 
COMPUTER IN1 and IN2 ports 
can be set.
(1)  
Use the ▲/▼ buttons to select the COMPUTER IN port to be set.
(2)   Use the ◄/► buttons to select 
the computer input signal type.
AUTO  ó SYNC ON G OFF
• Selecting the AUTO mode allows   
you to input a sync on G signal or component video signal from the 
port. Please refer to “Technical” for the connection of component 
video input to  COMPUTER IN1/2 port.
• In the AUTO mode, the...

42
INPUT menu
ItemDescription
RESOLUTION The resolution for the COMPUTER IN1 and COMPUTER IN2 input 
signals can be set on this projector.
(1)   In the INPUT menu select the RESOLUTION using the ▲/▼ 
buttons and press the ► button. 
The RESOLUTION menu will be   
displayed.
(2)   In the RESOLUTION menu select the 
resolution you wish to display using 
the ▲/▼ buttons.   
Selecting AUTO will set a resolution 
appropriate to the input signal.
(3)   Pressing the ► or ENTER button when 
selecting a STANDARD...

43
SETUP menu
SETUP menu
From the SETUP menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
ItemDescription
D-ZOOM Using the ◄/► cursor buttons adjusts the magnification ratio.
Small  ó Large
• The on-screen menu might be displayed outside of the image 
display area depending on the adjustment value of the ASPECT, 
D-ZOOM and 
 KEYSTONE....

44
SETUP menu
ItemDescription
PICT. POSIT. H
(CP-DW25WN)
Using the ▲/▼ cursor buttons selects the horizontal picture
position. LEFT  ó MID 
ó RIGHT
The PICT. POSIT. H is not changed if any of the following cases 
apply.
• The ASPECT is set to 16:9 or 16:10.
• The input signal has an aspect ratio of 16:9, 16:10 or verticallly
smaller than 16:10, while ASPECT is set to NORMAL.
• Horizontal size of the displayed image is full on the effective
display area, while the ASPECT is set to NATIVE.
• One of the...

45
SETUP menu
ItemDescription
AUTO ECO MODE Using the ▲/▼
 buttons turns on/off the AUTO ECO MODE.
ON  ó OFF
• When ON is selected, the projector will always be set to Eco mode 
at start-up regardless of the ECO MODE (
 45) setting. An OSD 
message “AUTO ECO MODE” will be displayed for tens of seconds 
when the projector starts with this function activated.
ECO MODE Using the ▲/▼ buttons switches the ECO MODE.
       NORMAL 
ó ECO 
ó INTELLIGENT ECO 
ó SAVER
• When the ECO is selected, acoustic noise...

46
SETUP menu
ItemDescription
INSTALLATION Pressing the ►button displays the dialog for changing the 
INSTALLATION setting.
Use the ▲/▼ buttons to select the desired setting on the 
INSTALLATION dialog.
If TRANSITION DETECTOR is ON and the INSTALLATION status 
is changed, the TRANSITION DETECTOR ON alarm (
 82) will be 
displayed when the projector is restarted.
STANDBY MODE Using ▲/▼ buttons switches the standby mode setting between 
NORMAL and SAVING. 
NORMAL  ó SAVING
When SAVING is selected, the...

47
SETUP menu
ItemDescription
MONITOR OUT While  the  image  signal  from  the  input  port  chosen  in  step  (1)  is 
projected, the image signal from the input port selected in step (2) is 
output to MONITOR OUT port.
(1) Choose a picture input port using ▲/▼ buttons. Choose STANDBY to select the picture  
output in the standby mode. 
(2)   Select one of the COMPUTER IN ports  
using ◄/► buttons.
Select OFF to disable the MONITOR OUT  
port for the input port or standby mode   
chosen in the step...

48
AUDIO menu
AUDIO menu
From the AUDIO menu, items shown in the table below 
can be performed. Select an item using the ▲/▼ cursor 
buttons, and press the ► cursor button or the ENTER 
button to execute the item. Then perform it according to 
the following table.
ItemDescription
VOLUME Using the ◄/► buttons adjusts the volume.
Low  ó High
SPEAKER Using the ▲/▼ buttons turns on/off the built-in speaker.
ON  ó OFF
When OFF is selected, the built-in speaker does not work.
AUDIO SOURCE While the image...

49
AUDIO menu
ItemDescription
MIC LEVEL
Using the ▲/▼ buttons switches the input level to match that of the 
microphone connected to the MIC port.
HIGH  ó LOW
HIGH: for a microphone with an amplifier. 
LOW:  for a microphone without an amplifier.
MIC VOLUME
Using the ◄/► buttons adjusts the volume of the microphone 
connected to the MIC port. Low  ó High 

50
SCREEN menu
SCREEN menu
From the SCREEN menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
ItemDescription
LANGUAGE Using the ▲/▼/◄/►
 buttons switches the OSD (On Screen 
Display) language.
ENGLISH  ó FRANÇAIS 
ó DEUTSCH 
ó  ESPAÑOL
       
  (shown in the LANGUAGE dialog)  
Press the ENTER or INPUT button to save the language...