Hitachi F7000 Instruction Manual

- vi - 
APPENDIX C  DETERMINATION COEFFICIENT OF   
CALIBRATION CURVE......................................... A-8 
APPENDIX D  INTEGRATION METHOD AND SMOOTHING ..... A-10 
APPENDIX E  DESCRIPTION OF FLUOROMETRY ................... A-16 
APPENDIX F  MEASUREMENT OF INSTRUMENTAL   
RESPONSE (CORRECTED SPECTRA) .............. A-26 
APPENDIX G  PARAMETER SETTING RANGE FOR   
ANALYSIS METHOD ............................................ A-41 
APPENDIX H  SAMPLING INTERVAL...

1.1 
1 - 1 
1.    FUNCTIONS AND SCREEN COMPOSITION   
 
1.1  Functions  
 
In this program, the following measurement modes are available:   
• Wavelength scan  
• Time scan  
• Photometry  
• 3-D scan  
•  3-D time scan 
 
Wavelength Scan 
 
(1)  Photometric value data can be printed at the specified wavelength intervals or at up to 12 
specified wavelengths.   
 
(2)  The function keys provide functions unique to the wavelength scan mode.   
Measurement:  [F4],  Stop:  [F6]  
 
(3)  Wavelength scan...

1.1  Functions 
1 - 2 
(4)  Measurement data and a calibration curve are displayed on the same screen window.    It is 
therefore possible to carry out measurement while observing the calibration curve.   
 
(5)  According to the coefficient of determination calculated automatically, judgment can be made on 
a degree of matching between standard values and a calibration curve.     
Two/three-wavelength calculation is permitted in preparation of a calibration curve.   
 
(6)  Statistical calculation is...

1.1 
1 - 3 
Secondary Processing of Data 
 
Measured data can be saved, and a variety of processings can be carried out on the saved data.   
 
(1)  Automatic reading of data (spectrum tracing)   
By placing the cursor on the currently displayed spectral graph, a photometric value at the 
cursor position can be read out.   
 
(2) Peak detection  
Peaks and valleys of the currently displayed spectrum are detected automatically.   
 
(3)  Change of scale   
A measured spectrum can be enlarged or reduced by...

1.1  Functions 
1 - 4 
(12)  Specification of printing items   
Items in a peak table can be selected and printed.   
 
(13)  Portrait or Landscape printing settable   
Printing can be made Portrait or Landscape.     
 
(14)  Collective spectrum printing   
Printing can be carried out just by specifying a file.   
 
(15)  Selection of spectrum to be displayed   
The spectrum to be displayed for overlaying is selectable.   
 
(16)  Automatic saving mode ON/OFF settable   
ON/OFF can be set in the sample...

1.2.1 
1 - 5 
1.2    Installation of FL Solutions Program   
 
1.2.1    Specifications of Personal Computer 
 
For running the FL Solutions 2.1 program on Microsoft Windows XP Professional, the following 
specifications must be met.   
 
OS  :  Microsoft Windows XP Professional   
CPU  :  CPU that allows the above OS to run in your computer   
Main memory  :  Minimum 256 MB   
Hard disk  :  Minimum free space 5 GB   
FD drive  :  One 3.5-inch FD drive   
CD-ROM drive  :  24× or faster   
Interface  :...

1.2    Installation of FL Solutions Program 
1 - 6 
 
Fig. 1-2   
 
2 Select “Add or Remove 
Programs.”  
• A window as shown in Fig.   
1-3 will appear.   
 
 
 
Fig. 1-3   
 
3 Select “Add New Programs.”   
• A window as shown in Fig.   
1-4 will appear.   
 
 
Fig. 1-4   
4 Set the furnished CD in the CD-
ROM drive and click CD or 
Floppy.  
• A window as shown in Fig.   
1-5 will appear. 
 
2
3 
4 

1.2.2 
1 - 7 
 
Fig. 1-5   
 
5 Click Next. 
• A window as shown in Fig.   
1-6 will appear.   
 
 
Fig. 1-6   
 
6 Make sure ‘D:\setup.exe’ is 
displayed, and then click Finish.  
• A window as shown in Fig.   
1-7 will appear.   
 
 
Fig. 1-7 
7 Click Next.  
• A window as shown in Fig.   
1-8 will appear.   
 
5
6 
6
7 

1.2    Installation of FL Solutions Program 
1 - 8 
 
Fig. 1-8   
 
8 Click Next.  
• A window as shown in Fig.   
1-9 will appear.   
 
 
Fig. 1-9   
 
9 Installation starts.   
• Upon completion of 
installation, a window as 
shown in Fig. 1-10 appears.   
 
 
Fig. 1-10   
10 For placing the shortcut of this 
program on the desktop, put the 
check mark in this check box.     
If you do not want to place it, 
remove the check mark.   
11 Click Finish.  
12 Take out the CD from the CD-
ROM drive.   
 
8...

1.2.3 
1 - 9 
1.2.3    Reinstallation of this Program   
 
Before reinstallation, the existing program needs to be deleted.     
Carry out the following procedure for deleting the program.   
 
 
Fig. 1-11   
 
1 Select [Start]-[Control 
Panel] and double-click the 
“Add or Remove Programs” 
icon.   
A window as shown in Fig. 
1-11 will open.   
2 Among the currently 
installed programs, select 
“FL Solutions for F-7000” 
and click Change/Remove.  
After removal, click Finish.  
Then, install the FL...