Hitachi Cp-X615 Projector Users Manual

							
3

3.1 Configuring and controlling the projector via a web browser (continued)
3. Management with Web browser software
3.1.12 Network Restart
Restarts the projector’s network connection.
ItemDescription
RestartRestarts the projector’s network connection in order to activate new configuration settings.
• Restarting requires you to re-log on in order to further control or 
configure the projector via a web browser. Wait 1 minute or more after clicking 
[Restart] button to log on again.
• The Logon menu (13) is displayed after restarting the projector’s network 
connection if the DHCP is set to ON.
NOTE
3.1.13 Logoff
When [Logoff] is clicked, the Logon menu is displayed. (13) 
						

							
3

3. Management with Web browser software
3.2 E-mail Aler ts
The projector can automatically send an alert message to the specified e-mail 
addresses when the projector detects a certain condition that is requiring 
maintenance or detected an error.
• Up to five e-mail addresses can be specified.
• The projector may be not able to send e-mail if the projector suddenly loses 
power.
NOTE
Mail Settings (18)
To use the projector’s e-mail alert function, please configure the following items 
through a web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
1) Enter “http://192.168.1.10/” into the address bar of the web browser. 
2) Enter the Administrator ID and password and click [Logon]. 
3) Click [Port Settings] on the main menu. 
4) Click [Enable] check box to open the SMTP Port. 
5) Click [Apply] button to save the settings.
6)   Click 
[Mail Settings] and configure each item. Refer to the item 3.1.5 Mail 
Settings (18) for further information. 
7) Click [Apply] button to save the settings.
• Click [Send Test Mail] button in [Mail Settings] to confirm that the 
e-mail settings are correct. The following mail will be delivered to the specified 
addresses.
NOTE
Subject line  :Test Mail  
Text  :Send Test Mail
  Date  
  Time  
  IP Address  
  MAC Address  
• A Network Restart is required after the SMTP Port configuration 
settings have changed. Click [Network Restart] and configure the following 
items.
NOTE 
						

							
33

3.2 E-mail Alerts (continued)
3. Management with Web browser software
8) Click [Alert Settings] on the main menu to configure the E-mail Alerts settings. 
9)  
Select and configure each alert item. Refer to the item 3.1.6 Alert Settings (19) 
for further information.
10) Click [Apply] button to save the settings.
Failure/Warning e-mails are formatted as follows:
Subject line  :   
Text  : 
  Date   
  Time  
  IP Address  
  MAC Address   
						

							
34

3. Management with Web browser software
3.3 Projector Management using SNMP
The SNMP (Simple Network Management Protocol) enables to manage the 
projector information, which is a failure or warning status, from the computer on 
the network. The SNMP management software will be required on the computer 
to use this function. 
• It is recommended that SNMP functions be carried out by a network 
administrator. 
• SNMP management software must be installed on the computer to monitor 
the projector via SNMP.
NOTE
SNMP Settings (17)
Configure the following items via a web browser to use SNMP.
Example: If the IP address of the projector is set to 192.168.1.10:
1) Enter “http://192.168.1.10/” into the address bar of the web browser. 
2) Enter the Administrator ID and Password and click [Logon]. 
3) Click [Port Settings] on the main menu. 
4)   Click 
[Enable] check box to open the SNMP Port. Set the IP address to send 
the SNMP trap to when a Failure/Warning occurs.
5) Click [Security Settings] on the main menu. 
6) Click [SNMP] and set the community name on the screen that is displayed.
7)   Configure the settings for Trap transmission of Failures/Warnings. Click 
[Alert Settings] on the main menu and select the Failure/Warning item to be 
configured. 
8)   Click 
[Enable] check box to send out the SNMP trap for Failures/Warnings. 
Clear [Enable] check box when SNMP trap transmission is not required. 
9) Click [Apply] button to save the settings.
• A Network Restart is required after the Community Name has been 
changed. Click [Network Restart] and configure the following items.
NOTE
• A Network Restart is required after the SNMP Port configuration 
settings have been changed. Click [Network Restart] and configure the 
following items.
NOTE 
						

							
35

3. Management with Web browser software
3.4 Event Scheduling
The scheduling function enables to setup scheduled events including power on / 
power off. It enables to be “self-management” projector. 
• You can schedule the following control events: Power ON/OFF, Input 
Source and Transferred Image Display. 
• The power on / off event has the lowest priority among the all events that are 
defined at the same time. 
• There are 3 types of Scheduling, 1) daily 2) weekly 3) specific date. (21)
• The priority for scheduled events is as follows 1) specific date 2) weekly 3) 
daily.
• Up to five specific dates are available for scheduled events. Priority is given to 
those with the lower numbers when more than one event has been scheduled 
for the same date and time (e.g., ‘Specific day No. 1’ has priority over ‘Specific 
day No. 2’ and so on. 
• Be sure to set the date and time before enabling scheduled events. (23)
NOTE 
						

							
3

3. Management with Web browser software
• In Standby mode the power indicator will flash green for approx. 3 
seconds when at least 1 “Power ON” schedule is saved.
• When the schedule function is used, the power cord must be connected to 
the projector and the outlet and the power switch must be turned on, [ | ]. The 
schedule function does not work when the power switch is turned off, [O] or 
the breaker in a room is tripped. The power indicator will lights orange or green 
when the projector gets is receiving the power.
NOTE
Schedule Settings (21)
Schedule settings can be configured from a web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
1) Enter “http://192.168.1.10/” into the address bar of the web browser.
2) Enter the Administrator ID and password and click [Logon].
3)   Click 
[Schedule Settings] on the main menu and select the required schedule 
item. For example, if you want to perform the command every Sunday , please 
select [Sunday].
4) Click [Enable] check box to enable scheduling.
5) Enter the date (month/day) for specific date scheduling.
6) Click [Apply] button to save the settings.
7)   Click 
[Add] to create new event. After configure the time, command and 
parameters, click [Register] to add the new event. To return the previous page, 
click [Cancel] button. 
8) Click [Delete] button when you want to delete a schedule.
There are three types of scheduling.
1) Daily: Perform the specified operation at a specified time every day . 
2)   Sunday ~ Saturday: Perform the specified operation at the specified time on a 
specified day of the week. 
3) Specific Date: Perform the specified operation on the specified date and time.
3.4 Event Scheduling (continued) 
						

							
37

3. Management with Web browser software
• A Network Restart is required after the Daylight Savings Time or 
SNTP configuration settings have been changed.
• The battery for the built in clock may be dead if the clock loses time even 
when the date and time have been set correctly. Replace the battery by 
following the instructions on replacing the battery. 
(Internal clock battery in the User’s Manual (concise))
• The internal clock’s time may not remain accurate. Using SNTP is 
recommended to maintain accurate time.
NOTE
Date/Time Settings (23)
The Date/Time setting can be adjusted via a web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
1)  Enter 
“http://192.168.1.10/” into the address bar of the web browser. Enter the 
Administrator ID and Password and click [Logon].
2)   Click 
[Date/Time Settings] on the main menu and configure each item. Refer 
to the item 3.1.8 Data/Time Settings for further information.
3) Click [Apply] button to save the settings. 
3.4 Event Scheduling (continued) 
						

							
38

3. Management with Web browser software
3.5  e-SHOT (Still Image Transfer) Display
The projector can display still images that are transferred via the network.
• It is possible to allocate the image file up to 4 in the maximum.
• The image file also can be displayed by using schedule function from the web 
browser. Refer to the item 3.4 Event Scheduling (35) in detail.
NOTE
Transfer image data
Display image data (1 - 4)
e-SHOT transmission requires an exclusive application for your PC. You can 
download it from the Hitachi web site (http://hitachi.us/digitalmedia or http://www .
hitachidigitalmedia.com). Refer to the manual for the application for instructions.
To display the transferred image, select the e-SHOT item in the NETWORK 
Menu. For more information, please see the description of the e-SHOT item of 
the NETWORK Menu. ( NETWORK Menu in User’s Manual (detailed) – 
Operating Guide)
Fig. 3.5 Still Image Transfer 
						

							
39

3.5  e-SHOT (Still Image Transfer) Display (continued)
Configure the following items from a web browser when e-SHOT is used.
Example: If the IP address of the projector is set to 192.168.1.10:
1) Enter "http://192.168.1.10/" into the address bar of the web browser.
2)   Enter the Administrator ID and password and 
click [Logon]. 
3) Click [Port Settings] on the main menu.
4)   Click the 
[Enable] check box to open the Image 
Transfer Port (Port: 9716). Click the [Enable] 
check box for the [Authentication] setting when 
authentication is required, otherwise clear the 
check box.
5) Click the [Apply] button to save the settings.
When the authentication setting is enabled, the following settings are required.
6) Click [Security Settings] on the main menu.
7)   Select 
[Network Control] and enter the desired authentication password. 
8) Click the [Apply] button to save the settings. 
• The Authentication Password will be the same for Network Control 
Port1 (Port: 23), Network Control Port2 (Port: 9715), and Image Transfer 
Port (Port: 9716).
NOTE
• The new configuration settings are activated after restarting the network 
connection. When the configuration settings are changed, you must restart 
the network connection. You can restart the network connection by clicking 
[Network Restart] on the main menu.
3. Management with Web browser software 
						

							
40

3. Management with Web browser software
3.6  Command Control via the Network
You can configure and control the projector via the network using RS-232C 
commands.
Communication Port
The following two ports are assigned for the command control.
Command Control Settings (17)
Configure the following items from a web browser when command control is used.
Example: If the IP address of the projector is set to 192.168.1.10:
1) Enter “http://192.168.1.10/” into the address bar of the web browser.
2) Enter the Administrator ID and password and click [Logon].
3) Click [Port Settings] on the main menu.
4)   Click 
[Enable] check box to open Network Control Port1 (Port: 23) to 
use TCP #23. Click [Enable] check box for [Authentication] setting when 
authentication is required, otherwise clear the check box.
5)   Click 
[Enable] check box to open Network Control Port2 (Port: 9715) to 
use TCP #9715. Click [Enable] check box for [Authentication] setting when 
authentication is required, otherwise clear the check box.
6) Click [Apply] button to save the settings.
TCP #23
TCP #9715
• Command control is not available via communication port (TCP #9716) 
(17) that is used for the e-SHOT transmission function.
NOTE