Hitachi Cp-X615 Projector Users Manual

3

3.1 Configuring and controlling the projector via a web browser (continued)
3. Management with Web browser software
3.1.12 Network Restart
Restarts the projector’s network connection.
ItemDescription
RestartRestarts the projector’s network connection in order to activate new configuration settings.
• Restarting requires you to re-log on in order to further control or 
configure the projector via a web browser. Wait 1 minute or more after clicking 
[Restart] button to log on again.
• The Logon...

3

3. Management with Web browser software
3.2 E-mail Aler ts
The projector can automatically send an alert message to the specified e-mail 
addresses when the projector detects a certain condition that is requiring 
maintenance or detected an error.
• Up to five e-mail addresses can be specified.
• The projector may be not able to send e-mail if the projector suddenly loses 
power.
NOTE
Mail Settings (18)
To use the projector’s e-mail alert function, please configure the following items 
through...

33

3.2 E-mail Alerts (continued)
3. Management with Web browser software
8) Click [Alert Settings] on the main menu to configure the E-mail Alerts settings. 
9)  
Select and configure each alert item. Refer to the item 3.1.6 Alert Settings (19) 
for further information.
10) Click [Apply] button to save the settings.
Failure/Warning e-mails are formatted as follows:
Subject line  :   
Text  : 
  Date   
  Time  
  IP Address  
  MAC Address   

34

3. Management with Web browser software
3.3 Projector Management using SNMP
The SNMP (Simple Network Management Protocol) enables to manage the 
projector information, which is a failure or warning status, from the computer on 
the network. The SNMP management software will be required on the computer 
to use this function. 
• It is recommended that SNMP functions be carried out by a network 
administrator. 
• SNMP management software must be installed on the computer to monitor 
the projector via...

35

3. Management with Web browser software
3.4 Event Scheduling
The scheduling function enables to setup scheduled events including power on / 
power off. It enables to be “self-management” projector. 
• You can schedule the following control events: Power ON/OFF, Input 
Source and Transferred Image Display. 
• The power on / off event has the lowest priority among the all events that are 
defined at the same time. 
• There are 3 types of Scheduling, 1) daily 2) weekly 3) specific date. (21)
• The...

3

3. Management with Web browser software
• In Standby mode the power indicator will flash green for approx. 3 
seconds when at least 1 “Power ON” schedule is saved.
• When the schedule function is used, the power cord must be connected to 
the projector and the outlet and the power switch must be turned on, [ | ]. The 
schedule function does not work when the power switch is turned off, [O] or 
the breaker in a room is tripped. The power indicator will lights orange or green 
when the projector...

37

3. Management with Web browser software
• A Network Restart is required after the Daylight Savings Time or 
SNTP configuration settings have been changed.
• The battery for the built in clock may be dead if the clock loses time even 
when the date and time have been set correctly. Replace the battery by 
following the instructions on replacing the battery. 
(Internal clock battery in the User’s Manual (concise))
• The internal clock’s time may not remain accurate. Using SNTP is 
recommended to...

38

3. Management with Web browser software
3.5  e-SHOT (Still Image Transfer) Display
The projector can display still images that are transferred via the network.
• It is possible to allocate the image file up to 4 in the maximum.
• The image file also can be displayed by using schedule function from the web 
browser. Refer to the item 3.4 Event Scheduling (35) in detail.
NOTE
Transfer image data
Display image data (1 - 4)
e-SHOT transmission requires an exclusive application for your PC. You can...

39

3.5  e-SHOT (Still Image Transfer) Display (continued)
Configure the following items from a web browser when e-SHOT is used.
Example: If the IP address of the projector is set to 192.168.1.10:
1) Enter "http://192.168.1.10/" into the address bar of the web browser.
2)   Enter the Administrator ID and password and 
click [Logon]. 
3) Click [Port Settings] on the main menu.
4)   Click the 
[Enable] check box to open the Image 
Transfer Port (Port: 9716). Click the [Enable] 
check box for the...

40

3. Management with Web browser software
3.6  Command Control via the Network
You can configure and control the projector via the network using RS-232C 
commands.
Communication Port
The following two ports are assigned for the command control.
Command Control Settings (17)
Configure the following items from a web browser when command control is used.
Example: If the IP address of the projector is set to 192.168.1.10:
1) Enter “http://192.168.1.10/” into the address bar of the web browser.
2) Enter...