Hitachi Cp-X3020 Projector Users Manual

12
Remote control
Remote control
About the remote control signal
The remote control works with the projector’s remote 
sensor. This projector has a remote sensor on the front.
The sensor senses the signal within the following range 
when the sensor is active:
60 degrees (30 degrees to the left and right of the sensor) 
within 3 meters about.
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote control 
starts to malfunction, try to replace the...

13
Remote control
Using as a simple PC mouse & keyboard
The accessory remote control works as a simple mouse 
and keyboard of the PC, when the projectors USB port 
(B type) connects with the PCs USB port (A type) port 
via a mouse cable.
(1)
(3)
(5)(2)
(4)
(6)
VIDEODOC.CAMERA
KEYSTONE
ASPECT SEARCH
BLANK
MUTE
MY BUTTON
POSITION
12
ESCENTERMENURESET
COMPUTERMY SOURCE/AUTOMAGNIFYPAGE
      UPVOLUME
DOWNo ONOFF9× FREEZE
(1) PAGE UP key: Press PAGE UP button.
(2) PAGE DOWN key: Press PAGE DOWN button.
(3)...

14
Power on/off
1.Make sure that the power cord is rmly and 
correctly connected to the projector and the 
outlet.
Turning on the power
2.Make sure that the POWER indicator is 
steady orange (
	62). Then remove the lens 
cover.
3.Press STANDBY/ON button on the 
projector or the remote control.
The projection lamp will light up and POWER  
indicator will begin blinking in green. When the power  
is completely on, the indicator will stop blinking and light in steady green 
(
	62).
Power on/off
To display...

15
Power on/off
Precaution for lens cover attachment and removal
When you attach or remove the lens cover, move it vertically up and down while keeping 
the knob to the right as illustrated in the gure. 

16
Operating
Operating
1.
Adjusting the volume
Use the VOLUME +/VOLUME - buttons to adjust the volume. 
A dialog will appear on the screen to aid you in adjusting the 
volume. If you do not do anything, the dialog will automatically 
disappear after a few seconds.
●  When 
 is selected for current picture input port, the volume 
adjustment is disabled. Please see AUDIO SOURCE item of 
AUDIO menu (
	38).
●  Even if the projector is in the standby state, the volume can be adjusted when 
both of following...

17
VIDEODOC.CAMERA
KEYSTONE
ASPECT SEARCH
BLANK
MUTE
MY BUTTON
POSITION
12
MENU
COMPUTERMY SOURCE/AUTO
MAGNIFYPAGE
      UPVOLUME
DOWNo ONOFF
9× FREEZE
Operating
1.Press VIDEO button on the remote control.  
Each time you press the button, the projector switches its 
input port from the current port as below. Selecting an input signal (continued)
●  
While ON is selected for AUTO SEARCH item in OPTION 
menu, the projector will keep checking every port sequentially 
till an input signal is detected (...

18
1.Press ASPECT button on the remote control.   
Each time you press the button, the projector switches the 
mode for aspect ratio in turn. 
Selecting an aspect ratio
● ASPECT button does not work when no proper signal is inputted.
● NORMAL mode keeps the original aspect ratio setting.
1.Press SEARCH button on the remote control.
The projector will start to check its input ports as below in 
order to nd any input signals.
When an input is found, the projector will stop searching 
and display the...

19
Operating
Adjusting the projector's elevator
When the place to put the projector is slightly uneven to the left or right, use the 
elevator feet to place the projector horizontally. 
Using the feet can also tilt the projector in order to project at 
a suitable angle to the screen, elevating the front side of the 
projector within 
12 degrees.
This projector has 2 elevator feet and 2 elevator knobs. An elevator foot is 
adjustable while pulling up the elevator knob on the same side as it.
1.Holding...

20
Operating
1.Press POSITION button on the remote control when no menu is 
indicated. 
The “POSITION” indication will appear on the screen.
Adjusting the position
2.Use the ▲/▼/◄/► cursor buttons to adjust the picture position.
When you want to reset the operation, press RESET button on 
the remote control during the operation.
To complete this operation, press POSITION button again. Even if 
you do not do anything, the dialog will automatically disappear 
after a few seconds.
●  
When this function is...

21
Operating
1.Press KEYSTONE button on the remote 
control. A dialog will appear on the screen to 
aid you in correcting the distortion.
Correcting the keystone distortions
2.Use the ▲/▼ cursor buttons to select AUTO or MANUAL 
operation, and press the ► button to perform the following.
(1)  AUTO executes automatic vertical keystone correction. 
(2)  MANUAL displays a dialog for keystone correction.  
Use the ◄/► buttons for adjustment.
To close the dialog and complete this operation, press 
KEYSTONE...