Hitachi Cp-X3020 Projector Users Manual

2
Contents
Contents
Introduction ...............3
Features ......................3
Checking the contents of package ...3
Part names ................4
Projector ......................4
Control panel ...................5
Rear panel  ....................5
Remote control .................6
Setting up .................7
Arrangement ...................7
Connecting your devices ..........9
Connecting power supply ........11
Using the security bar and slot . . . .11
Remote control............12
Installing the...

3
Introduction
• Keep the original packing materials, for future reshipment. Be sure 
to use the original packing materials when moving the projector. Use special 
caution for the lens. NOTE
Introduction
The projector provides you with the broad use by the following features.
Checking the contents of  package
9    This projector has a variety of I/O ports that supposedly cover for any 
business scene.
9    This projector realizes the large projection image, even if in a small space.
9    The new double...

4
Part names
Part names
Projector
(1)  Lamp cover (	56) 
The lamp unit is inside.
(2) Focus ring (	19)
(3) Zoom ring (
	19)
(4) Control panel (
	5)
(5) Elevator buttons (x 2) (
	19)
(6) Elevator feet (x 2) (
	19)
(7) Remote sensor (
	12)
(8) Lens (
	60)
(9) Intake vents
(10)  Filter cover (
	58) 
The air lter and intake vent are 
inside.
(11) Speaker (	38)
(12) Exhaust vent
(13)  AC IN (AC inlet) (
	11)
(14) Rear panel (
	5)
(15) Security bar (
	11)
(16) Security slot (
	11)
►HOT!: Do not touch around...

5
Part names
Control panel
(1) STANDBY/ON button (	14)
(2) INPUT button (
	16, 24)
(3)  MENU button (
	24) 
It consists of four cursor buttons.
(4) 
BLANK button (	23)
(5) POWER indicator (
	11, 14, 62)
(6) TEMP indicator (
	62)
(7) LAMP indicator (
	62)
Rear panel (	9)
(1) VIDEO port 
(2) S-VIDEO port 
(3) AUDIO IN1 port 
(4) AUDIO IN2 port 
(5) AUDIO OUT port 
►Use the shutdown switch only when the projector is not 
turned off by normal procedure, since pushing this switch stops operation of the...

6
Part names
Remote control
(1) VIDEO button (	17)
(2) COMPUTER button (
	17)
(3) SEARCH button (
	18)
(4) STANDBY/ON button (
	14)
(5) ASPECT button (
	18)
(6) AUTO button (
	20)
(7) BLANK button (
	23)
(8) MAGNIFY - ON button (
	22)
(9) MAGNIFY - OFF button (
	22)
(10) MY SOURCE/DOC.CAMERA button (
	17, 47)
(11) VOLUME - button (
	16)
(12) PAGE UP button (
	13)
(13) PAGE DOWN button (
	13)
(14) VOLUME + button (
	16)
(15) MUTE button (
	16)
(16) FREEZE button (
	23)
(17) MY BUTTON - 1 button (
	47)...

7
Setting up
Install the projector according to the environment and manner the projector will be 
used in.
Arrangement
Refer to the illustrations and tables below to determine screen size and projection 
distance.
The values shown in the table are calculated for a full size screen: 1024 x 768
  a  Screen size (diagonal)    b  Projection distance (±10%)
 c1 , c2  Screen height (±10%)
On a horizontal surface
Suspended from the ceiling
• Keep a space of 30 cm or more between the 
sides of the projector and...

8
Setting up
►Place the projector in a stable horizontal position. If the 
projector falls or is knocked over, it could cause injury and/or damage to the 
projector. Using a damaged projector could then result in re and/or electric 
shock.
•  Do not place the projector on an unstable, slanted or vibrational surface such 
as a wobbly or inclined stand.
•  Do not place the projector on its side, front or rear position. 
•  Consult with your dealer before a special installation such as suspending from 
a...

9
Setting up
VIDEO OUTL  R
AUDIO OUT
AUDIO OUTRGB OUTAUDIO OUTRGB OUTRS-232CRGB IN
L  R
AUDIO OUTS-VIDEO OUT
USB
L  R
AUDIO IN       Y       CB/PB     CR/PRCOMPONENT VIDEO OUTL  R
AUDIO OUT
Connecting your devices
Be sure to read the manuals for devices before connecting them to the projector. 
Make sure that all the devices are suitable to be connected with this product, and 
prepare the cables required to connect. Please refer to the following illustrations 
to connect them. To input component video...

10
Setting up
• Be sure to read the manuals for devices before connecting them to 
the projector, and make sure that all the devices are suitable to be connected 
with this product. Before connecting to a PC, check the signal level, the signal 
timing, and the resolution.
-  Some signal may need an adapter to input this projector.
-  Some PCs have multiple screen display modes that may include some signals 
which are not supported by this projector. 
-  Although the projector can display signals with...

11
Setting up
Connecting power supply
1.Put the connector of the power cord into the 
AC IN (AC inlet) of the projector.
2.Firmly plug the power cord’s plug into the 
outlet. In a couple of seconds after the 
power supply connection, the POWER 
indicator will light up in steady orange.
►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in re and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, consult...