Hitachi Cp-X206 Projector Users Manual



Setting up
• Be sure to read the manuals for devices before connecting them to the projector, and make sure that all the devices are suitable to be connected with this product. Before connecting to a PC, check the signal level, the signal timing, and the resolution.
-  Be sure to consult to the administrator of the network. Do not connect LAN port to any network that might have the excessive voltage. 
-   Some signal may need an adapter to input this projector.
-   Some PCs have multiple...



Setting up
Connecting power supply
1.Put the connector of the power cord into the 
AC IN (AC inlet) of the projector.
2.Firmly plug the power cord’s plug into the 
outlet.
►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, consult 
your dealer to get a new one.
• Only plug the power cord into an outlet whose voltage is matched to the...

3

Remote control
Remote control
About the remote control signal
The remote control works with the projector’s remote 
sensor. This projector has a remote sensor on the front.
The sensor senses the signal within the following range 
when the sensor is active:
60 degrees (30 degrees to the left and right of the sensor) 
within 3 meters about.
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote control 
starts to malfunction, try to replace the...

4

Remote control
Changing the frequency of  remote control signal
The accessory remote control has the two choices on signal frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control does not function properly, attempt to change the signal frequency.In order to set the Mode, please keep pressing the combination of two buttons listed below simultaneously for about 3 seconds.
Using as a simple PC mouse & keyboard
The accessory remote control works as a simple mouse and keyboard of the PC, when...

5

Power on/off
1.Make sure that the power cord is firmly and correctly connected to the projector and the outlet.
Turning on the power
2.Remove the lens cover, and set the power switch to ON position (marked “ I ”). The POWER indicator will light up in steady orange (67). Then wait several seconds because the buttons may not function for these several seconds.
3.Press STANDBY/ON button on the projector or the remote control. The projection lamp will light up and POWER indicator will begin...

6

               COMPUTER IN 1  COMPUTER IN 2  
        VIDEO  S-VIDEO  COMPONENT (Y, Cb/Pb, Cr/Pr)
Operating
Operating
1.
Adjusting the volume
Use the VOLUME +/VOLUME - buttons to adjust the volume. A dialog will appear on the screen to aid you in adjusting the volume. If you do not do anything, the dialog will automatically disappear after a few seconds.
●  When  is selected for current picture input port, the volume adjustment is disabled. Please see AUDIO item of AUDIO menu (36).
●   When...

7

Operating
1.Press VIDEO button on the remote control.  Each time you press the button, the projector switches its input port from the current port as below.
Selecting an input signal (continued)
●  
While TURN ON is selected for AUTO SEARCH item in OPTION menu, the projector will keep checking every port sequentially till an input signal is detected (41). If VIDEO button is pushed when COMPUTER IN1 or COMPUTER IN2 port is selected, the projector will check COMPONENT port first. 
1.Press ASPECT...

8

Operating
Adjusting the projector's elevator
When the place to put the projector is slightly uneven to the left or right, use the 
elevator feet to place the projector horizontally. 
Using the feet can also tilt the projector in order to project at 
a suitable angle to the screen, elevating the front side of the 
projector within 10 degrees.
This projector has 2 elevator feet and 2 elevator buttons. An elevator foot is adjustable 
while pushing the elevator button on the same side as it....

9

Operating
1.Press POSITION button on the remote control when no menu 
is indicated. 
The “POSITION” indication will appear on the screen.
Adjusting the position
2.Use the ▲/▼/◄/► cursor buttons to adjust the picture position.
When you want to reset the operation, press RESET button on 
the remote control during the operation.
To complete this operation, press POSITION button again. 
Even if you do not do anything, the dialog will automatically 
disappear after a few seconds.
●  
When this...

0

Operating
• The zoom level can be finely adjusted. Closely watch the screen to 
find the level you want.
NOTE
1.Press the ON button of MAGNIFY on the remote control.  The “MAGNIFY” indication will appear on the screen and the projector will go into the MAGNIFY mode. When the ON button of MAGNIFY is pressed first after the projector is started, the picture will be zoomed twice. The indication will disappear in several seconds with no operation.
Using the magnify feature
2.Use the ▲/▼ cursor...