Hitachi Cp-X10000 Users Manual

51
OPTION menu
ItemDescription
SERVICE
(continued) LENS TYPE
Select the lens type currently used using the ▲/▼ buttons. 1:USL-801 
ó 2:SL-802 
ó 3:SL-803 
ó 4:SD-804
                7:AUTO  ó 6:UL-806 
ó 5:LL-805
Please select one of them referring to the following.
1: for an ultra short throw lens (USL-801)
2: for a short throw lens (SL-802)
3: for a short throw lens (SL-803)
4: for a standard lens (SD-804)
5: for a long throw lens (LL-805)
6: for an ultra long throw lens (UL-806)
7:AUTO
• Selecting the...

52
OPTION menu
ItemDescription
SERVICE
(continued) REMOTE ID
Use the ▲/▼ buttons on the REMOTE ID menu to select ID and 
press the ► button
.
ALL 
ó 1 
ó 2 
ó 3 
ó 4
The projector is controlled by the remote control whose ID button is 
set the same number as this number. When the ALL is selected, the 
projector is controlled by a remote control irrespective of the ID setting. 
COMMUNICATION
Selecting this item displays COMMUNICATION menu. In this menu, you can configure the communication settings 
of the...

53
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION (continued)
DAISY CHAIN: Select this type, if it is required to 
connect multiple projectors using a shared RS-232C 
communication bus, from the computer. (
Network 
Guide - 3.8 Multi-controlling the plural projectors (using 
DAISY CHAIN function))
OFF: Select this mode if you want to output no data 
from the 
CONTROL OUT port. 
SERIAL IN SETTING/SERIAL OUT SETTING
In these menus, you can select 
the communication condition for 
each of...

54
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION (continued)
RESPONSE LIMIT TIME
This menu is available only when the NETWORK 
BRIDGE is selected for the COMMUNICATION 
TYPE and the HALF-DUPLEX is selected for the 
TRANSMISSION METHOD.
Select the time period to wait for receiving response 
data from other devise communicating by the 
NETWORK BRIDGE and the HALF-DUPLEX through 
the 
CONTROL OUT port.
OFF  ó 1s 
ó 2s 
ó 3s
    
OFF: Select this mode if it is not required to check the...

55
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION (continued)
COMMUNICATION GROUP / COMMUNICATION ID
This menu is available only when DAISY CHAIN is 
selected for the COMMUNICATION TYPE.
In simultaneous control of multiple projectors by 
a daisy chain, you can give the projectors the 
communication group identification and the ID number 
to identify projectors connected in the same bus.
COMMUNICATION GROUP:A
 ó  B 
ó  C … O 
ó  P 
COMMUNICATION ID:
1 ó  2 
ó  3 … 63 
ó  64 
INFORMATION...

56
NETWORK menu
Remember that incorrect network settings on this 
projector may cause trouble on the network. Be sure 
to consult with your network administrator before 
connecting to an existing access point on your 
network.
Select “NETWORK” from the main menu to access 
the following functions. 
Select an item using the ▲/▼ cursor buttons on the projector or remote control, 
and press the ► cursor button on the projector or remote control, or 
ENTER 
button on the remote control to execute the item....

57
NETWORK menu
ItemDescription
SETUP
(continued)
IP 
ADDRESS
Use the ▲/▼/◄/► 
buttons to enter the IP 
ADDRESS. 
This function can only be used when DHCP is set to 
OFF.
• The IP ADDRESS is the number that identifies this 
projector on the network. You cannot have two devices 
with the same IP ADDRESS on the same network.
• The IP ADDRESS “0.0.0.0” is prohibited.
SUBNET  MASK Use the ▲/▼/◄/► 
buttons to enter the same 
SUBNET MASK used by 
your PC. 
This function can only be used when DHCP is set to...

58
NETWORK menu
ItemDescription
PROJECTOR  NAME (1)  
Use the▲/▼ buttons on the 
NETWORK menu to select the 
PROJECTOR NAME menu 
and press the ► button. The 
PROJECTOR NAME dialog will 
be displayed.
(2)    The current PROJECTOR NAME will be displayed on the first 3 
lines. If not yet written, the lines will be blank.
Use the ▲/▼/◄/► buttons and the 
ENTER or VIDEO button to 
select and enter characters.
The 
RESET or COMPUTER button can be used to erase 1 
character at a time. Also if you move the...

59
NETWORK menu
ItemDescription
MY IMAGE Selecting this item displays the MY 
IMAGE menu. 
The application software “PJImage” 
is required to store image(s) into the 
projector.
Use the ▲/▼ buttons to select an item which is a still image by the 
MY IMAGE
 (
 MY IMAGE (Still Image Transfer) Display of the 
User’s Manual - Network Guide)  and the ► or ENTER button to 
display the image.
• The item without image stored cannot be selected.
• The image names are each displayed in 16 characters or less.
To...

60
NETWORK menu
ItemDescription
INFORMATION Selecting this item displays the NETWORK -INFORMATION- dialog 
for confirming the network settings.
• Only the first 16 characters of the projector neme are displayed.
• Nothing (blank) is shown in the “PROJECTOR NAME” field until 
you setup the item (
58).
• When the voltage level of the battery for the built in clock 
decreases, the set time may become incorrect even though accurate 
date and time are input. Replace the battery suitably
 (70).
• IP ADDRESS,...