Hitachi Cp-X10000 Users Manual

11
Setting up
Connecting with your devices
Before connecting the projector to your devices, check the manual of the device in 
order to make sure that the device is suitable to connect with this projector and to 
check what is required for the connection.
Consult your dealer when the required accessory did not come with the product or 
the accessory is damaged. It may be regulated under some standard.
►Use only the accessories specified or recommended by 
manufacturer. Modify neither a projector nor...

12
 Setting up 
 Control from the computer 
HDMIREMOTE
CONTROL LAN
DVI-D
CONTROL IN CONTROL OUT
IN
OUT S-VIDEO
VIDEO 1 COMPUTER IN1 COMPUTER IN2MONITOR
OUT
BNC VIDEO 2
R/Cr/Pr G/Y B/Cb/Pb H V
Y
Cb/Pb
Cr/Pr
K
HDMI REMOTE
CONTROL LAN
DVI-D
CONTROL IN CONTROL OUT
IN
OUT S-VIDEO
VIDEO 1 COMPUTER IN1 COMPUTER IN2MONITOR
OUT
BNC VIDEO 2
R/Cr/Pr G/Y B/Cb/Pb H V
Y
Cb/Pb
Cr/Pr
K
HDMI
DVI-D S-VIDEO
OUT VIDEO
OUT COMPONENT
Y  Cb/Pb  Cr/PrVIDEO
OUT
RS-232CRGB OUT RGB OUT RGB OUT
LAN
HDMI REMOTE
CONTROL LAN
DVI-D...

13
 Setting up 
 Connecting your devices (continued) 
Example of connecting with another projector or a display device
HDMIREMOTE
CONTROL LAN
DVI-D
CONTROL IN CONTROL OUT
IN
OUT S-VIDEO
VIDEO 1 COMPUTER IN1 COMPUTER IN2MONITOR
OUT
BNC VIDEO 2
R/Cr/Pr G/Y B/Cb/Pb H V
Y
Cb/Pb
Cr/Pr
K
HDMI REMOTE
CONTROL LAN
DVI-D
CONTROL IN CONTROL OUT
IN
OUT S-VIDEO
VIDEO 1 COMPUTER IN1 COMPUTER IN2MONITOR
OUT
BNC VIDEO 2
R/Cr/Pr G/Y B/Cb/Pb H V
Y
Cb/Pb
Cr/Pr
K
HDMI
DVI-D S-VIDEO
OUT VIDEO
OUT COMPONENT
Y  Cb/Pb...

14
Setting up
Connecting your devices (continued)
• Be sure to read the manuals for devices before connecting them to the projector, 
and make sure that all the devices are suitable to be connected with this product. 
• Before connecting to a PC, check the signal level, the signal timing, and the resolution.-   Be sure to consult to the administrator of the network. Do not connect LAN port to any 
network that might have excessive voltage.
- Some signal may need an adapter to input this projector.
-...

15
Setting up
Connecting power supply
1.Make sure that the power switch of the projector is set to the off-position 
(marked with “
O”).
2.Insert the socket end of the power cord into the AC IN (AC inlet) of the 
projector.
►Do not connect the projector to a power supply when the lens 
unit is not attached.
►Use this projector from only the specified power supply in accordance with the 
label indication on the projector.
►Use a power outlet that is close to the projector and easily accessible.
►Do not...

16
Remote control
Remote control
Putting batteries
The remote control needs the two batteries of the following type. 
1.Remove the battery cover in the back of the 
remote control. Push lightly the knob of the 
battery cover while pulling it up.
2.Put the batteries into the battery holder, according to the 
polarity markings “+” and “-“ inside the holder.
3.Put the battery cover back into place until it clicks.
►Be careful not to press the LASER button when loading the 
batteries. It is dangerous if a...

17
 Remote control 
BLANKLASER
FREEZELASER
INDICATORDIGITAL
STANDBY/ON
COMPUTER
LENS SHIFT KEYSTONEID 3
ID 4
ID 2 ID 1VIDEOAUTO ASPECTRESETMENUMAGNIFYON
OFF
3
4ENTERFOCUS+
-POSITION
PbyPZOOM+
-
1
2MY BUTTON
MY SOURCESHUTTER
 Transmitting condition 
 The remote control works with the remote 
sensors on the projector using infrared light 
(Class 1 LED). The remote sensor senses the 
remote control signals reached into the range 
within 60 degrees (to right and left) and 3 meters 
about from the sensor....

18
Remote control
BLANKLASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON
COMPUTER
LENS SHIFT KEYSTONEID 3
ID 4
ID 2 ID 1VIDEO
AUTO ASPECTRESETMENU
MAGNIFYON
OFF
3
4
ENTER
FOCUS+
-
POSITION
PbyP
ZOOM+
-
1
2
MY BUTTON
MY SOURCE
SHUTTER
Using as a wired remote control
The accessory remote control works as a wired remote control, 
when the wired control port at the bottom of the remote control 
connects with the 
REMOTE CONTROL port on the back of the 
projector via an audio cable with 3.5 diameter stereo mini...

19
Operating
1.Make sure that the power cord is firmly and 
correctly connected to the projector and the outlet.
2.Press down the side marked “I” on the power 
switch.
The 
POWER indicator will light up in steady 
orange. 
Then wait for the buttons to become ready. It may 
take several seconds
.
3.Press the STANDBY/ON button (on the projector 
or the remote control).
The projection lamp will light up and the 
POWER 
indicator will begin blinking in green. When the 
power is completely on, the indicator...

20
Operating
1.
Turning off
2.Press the STANDBY/ON button again while the 
message is shown.
 
The projector lamp will go off, and the POWER 
indicator will begin blinking in orange.
Then the 
POWER indicator will stop blinking 
and light in steady orange when lamp cooling is 
complete.
3.After making sure that the POWER indicator lights in steady orange, and 
press down the side marled “
O” on the power switch.
  The 
POWER indicator will go off.
• Use the shutdown switch only when the projector can be...