Hitachi Cp-X10000 Users Manual

41
SETUP menu
ItemDescription
 
 KEYSTONE Using the ◄/► buttons corrects the horizontal keystone distortion.
Shrink the left of the image  ó Shrink the right of the image
• The adjustable range of this function will vary among inputs. For 
some input, this function may not work well.
• When the zoom adjustment is set to the TELE (telephoto focus), 
this function may be excessive. This function should be used when 
the zoom adjustment is set to the full WIDE (wide-angle focus) 
whenever possible.
• When...

42
SCREEN menu
SCREEN menu
From the SCREEN menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor 
button on the projector or remote control, or 
ENTER 
button on the remote control to execute the item. 
Then perform it according to the following table.
Item Description
LANGUAGE Using the ▲/▼/◄/► buttons switches the OSD (On Screen 
Display) language.
MENU POSITION Using the ▲/▼/◄/► buttons adjusts...

43
SCREEN menu
ItemDescription
START UP Using the ▲/▼ buttons switches the mode for the start-up screen.
The start-up screen is a screen displayed when no signal or an 
unsuitable signal is detected.
MyScreen  ó ORIGINAL 
ó OFF
    
Feature
MyScreen Screen can be registered by the MyScreen item 
(
44).
ORIGINAL Screen preset as the standard screen.
OFF Plain black screen.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL 
screen will change to the BLANK screen (
26) after several...

44
SCREEN menu
ItemDescription
MyScreen This item allows you to capture an image for use as a MyScreen 
image which can be used as the BLANK screen and START UP 
screen. Display the image you want to capture before executing the 
following procedure.
1.  
Selecting this item displays a dialog 
titled “MyScreen”. It will ask you if 
you start capturing an image from the 
current screen.
Please wait for the target image to be displayed, and press the 
ENTER or VIDEO button when the image is displayed. The...

45
SCREEN menu
ItemDescription
MESSAGE Using the ▲/▼ buttons turns on/off the message function.
ON  ó OFF
When the ON is selected, the following message function works.“AUTO IN PROGRESS” while automatically adjusting
“NO INPUT IS DETECTED”
“SYNC IS OUT OF RANGE”
“INVALID SCAN FREQ”
“Searching….” while searching for the input
“Detecting….” while an input signal is detected
The indication of the input signal displayed by changing 
The indication of the aspect ratio displayed by changing
The indication of...

46
SCREEN menu
ItemDescription
TEMPLATE Using the ▲/▼ buttons switches the mode for 
the template screen. 
Press the ► button to display the selected 
template, and press the ◄ button to close the 
displayed screen.
The last selected template is displayed when 
the 
MY BUTTON allocated to the TEMPLATE 
function is pressed (
 49). TEST PATTERN 
ó DOT-LINE1DOT-LINE4 
ó DOT-LINE3 
ó DOT-LINE2
C.C.
(Closed Caption)
The C.C. is the function that displays a transcript or dialog of the 
audio portion of a...

47
OPTION menu
OPTION menu
From the OPTION menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor 
button on the projector or remote control, or 
ENTER 
button on the remote control to execute the item, 
except for the items LAMP TIME and FILTER TIME. 
Then perform it according to the following table.
Item Description
SOURCE SKIP
The port that is set to the "SKIP" is ignored in searching by...

48
OPTION menu
ItemDescription
DIRECT ON Using the ▲/▼ buttons turns on/off the DIRECT ON function.
ON  ó OFF
When set to the ON, the lamp in projector will be
automatically turned on without the usual procedure ( 19), only
when the projector is supplied with the power after the power was
cut while the lamp was on.
• This function does not work as long as the power has been
supplied to the projector while the lamp is off.
• After turning the lamp on by the DIRECT ON function, if neither input
nor...

49
OPTION menu
ItemDescription
MY BUTTON This item is to assign one of the following functions to 
MY BUTTON 
-(1 to 4) on the remote control ( 7).(1) Use the ▲/▼ buttons on the MY BUTTON menu to select a MY BUTTON - (1 
to 4) and press the ► button to display the MY BUTTON setup dialog.
(2) Then using the ▲/▼/◄/► buttons sets one of the following functions to the 
chosen button.
• COMPUTER IN1: Sets port to COMPUTER IN1.
• COMPUTER IN2: Sets port to COMPUTER IN2.
• BNC: Sets port to BNC.
• HDMI: Sets...

50
OPTION menu
ItemDescription
SERVICE Selecting this item displays the SERVICE menu.
Select an item using the ▲/▼ buttons, and press the ► button or 
the 
ENTER button on the remote control to execute the item.
FAN SPEED
Using the ▲/▼ buttons switches the rotation 
speed of the cooling fans. The HIGH is the 
mode for use at highlands etc. Note that the 
projector is noisier when the HIGH is selected. HIGH  ó NORMAL
AUTO ADJUST
Using the ▲/▼ buttons to select one of the mode. 
When the DISABLE is...