GTE Omni Scbs Installation And Maintenance Manual

inal Instlation (Continued)
GE al!avn SLBCS1 PROCEDURE 
1
4.PLUG THE AC POWER SUPPLY
ADAPTER INTO THE POWER
OUTLET.AC ADAPTER
AC ADAPTER
5.PLUG THE ROUND END OF THE AC
POWER SUPPLY ADAPTER INTO
THE CSD TELEPHONE.
NOTE:REFER TO OPERATIONS MANUAL SUPPLIED WITH 
CUSTOMER-
SUPPLIED DATA TERINAL FOR OPERATING INSTRUCTIONS.
4.40 

Message Waiting on SLT Instruments1
 DESCRIPTION 1
eMESSAGES CAN BE LEFT AT SLT INSTRUMENTS
(DIAL PULSE OR DTMF) EQUIPPED WITH
MESSAGE WAITING LAMPS.
lMESSAGE WAITING FEATURE FOR SLT
INSTRUMENTS IS ACTIVATED THROUGH A
STRAPPING OPTION ON THE RGEN CARD AND
TWO DATA BASE COMMANDS.[PROCEDURE 
1
1.CUT STRAPPING JUMPER ON RGEN CARD (SEE
DIAGRAM) OR IF EQUIPPED, SLIDE MESSAGE
WAITING SWITCH (LOCATED IN SAME PLACE) TO
ON.
2.ACTIVATE MESSAGE WAITING ON SLT
INSTRUMENTS FOR SYSTEM WITH CMC-102.
(REFER TO PACKAGE...

Optional External Paging Installation
GUE OMNU SBCS.
DIAGRAM REPRESENTS A TYPICAL EXAMPLE OF25 PAIR CDF BLOCK7TIPCROSS CONNECTIONS FOR A CUSTOMER-
SUPPLIED EXTERNAL PAGING AMPLIFIER..
EXTERNAL PAGING REQUIRES ONE PAIR OF
WIRES FOR ITS INTERFACE TO A 
4BWC CARD
(SAME AS CO TRUNK INSTALLATION). EACH
4BWC CARD HAS FOUR CIRCUITS AND ONLY
EVERY OTHER PAIR OF PINS IS USED ON THE
CONNECTING BLOCK..
OPERATION MAY REQUIRE 24 VOLT POWER
SUPPLY (DEPENDENT ON CUSTOMER-
SUPPLIED EQUIPMENT)
25 PAIR
CABLE
REFER TO CDF...

Laboratory
Installation1.POWER SYSTEM OFF.
2.ENSURE THAT PROPER ELECTROSTATIC GROUNDING PROCEDURES ARE FOLLOWED PRIOR TO
HANDLING PCB CARDS.
3.BEGIN REPLACING AND INSTALLING THE DESIGNATED PRINTED CIRCUIT BOARDS IN CARD
SLOTS IDENTIFIED BELOW (IF NOT PREVIOUSLY INSTALLED IN MODULE I). ENSURE THAT CARD
COMPONENTS ARE ON LEFT SIDE OF THE BOARDS.
(A)INSERT AND SEAT AN INTERFACE CARD FOR CSD/DTA INSTRUMENTS (8DTC) IN CARD
SLOT 00.
(B)REPLACE THE CPMA CARD IN SLOT 20 WITH THE ENHANCED CONTROL PROCESSOR
MEMORY...

/’Laboratory
InstallationActivity
- Package B
(4.2) (Continued)
9.WIRE CROSS CONNECTION AND INSTALL EXTERNAL SPEAKER TO 4BWC CARD IN SLOT 18,
CIRCUIT 3.
10.POWER SYSTEM ON AND RESET SYSTEM BY PRESSING RESTART BUTTON ON CPMB CARD WITH
TOGGLE SWITCH IN CENTER POSITION.11. REPROGRAM THE ODDB.
4.44 

Review Exercise- Package B
Installlation (4.2)INSTRUCTIONS:THE FOLLOWING EXERCISE CONSISTS OF MULTIPLE CHOICE, TRUE/FALSE, FILL IN THE BLANK, OR
MATCHING TYPE QUESTIONS. ALL AVAILABLE RESOURCES (I.E. STUDENT WORKBOOK, NOTES AND
GTEP MANUAL) MAY BE USED AS REFERENCES. SUBMIT EXERCISE TO INSTRUCTOR FOR GRADING
WHEN LAST QUESTION HAS BEEN COMPLETED.
1. (TRUE OR FALSE)
CPMB CAN BE INSTALLED AS A COMMON CONTROL CARD WITH SWC AND 
MEMA CARDS.
2. (TRUE OR FALSE)
‘REPLACING CPMB OR MEMB AUTOMATICALLY DELETES THE...

_,-,Review Exercise 
-Package B
Installation 
(4.2) (Continued)
9.What card slots may be used for 8DTC cards when CSD telephones are installed without Data Terminal Adapters?
10.Identify the correct descriptions for the RS-232-C pin configuration required for the RS-232-C port on a CSD equipped with a
DTA:
PINSIGNALDESCRIPTION
1FGPROTECTIVE GROUND
2TD
3RDRECEIVED DATA
4RTS
5CTS
6
DSRDATA SET READY
7SCSIGNAL GROUND
8RLSD
9_____________________________________
14_______--_-_______________-__________...

Student Notes
4.47 

PACKAGE B
DATA BASE
ADMINISTRATION
4.48
i 

GIVEN:00
0
0
0
ACTION:0
0
0
CRITERIA:0
0
GTE OMNI SBCSGTE 
OMNI SBCS PACKAGE B EQUIPMENT AND
PERIPHERALSPORTABLE MAINTENANCE PANEL
OMNI SBCS COURSE AND SITE DOCUMENTATION
PACKAGE
REVIEW EXERCISEIDENTIFY FUNCTIONS AND APPLICATIONS OF
PACKAGE B CMC COMMANDS.
MODIFY PARAMETER VALUES FOR PACKAGE B CMCCOMMANDS.
COMPLETE REVIEW EXERCISE.DEMONSTRATION OF ABOVE TASKS IN ACCORDANCE
WITH PROCEDURES OUTLINED IN OMNI SBCS GTEP
MANUAL AND OMNI SBCS STUDENT WORKBOOK.
REVIEW EXERCISE WILL BE COMPLETED CORRECTLYIN...