GTE Omni Scbs Installation And Maintenance Manual

PACKAGE B
INSTALLATION
4.30 

4.2 Enling Objective
GlVEN:0
@
0
0
0
ACTION:0
e
0
0
0
0
CRITERIA:0
0
GTE OMNI SBCS (PREVIOUSLY INSTALLED)
GTE 
OMNI SBCS PACKAGE B EQUIPMENT AND PERIPHERALS
-CPMB, MEMB, 8DTC, AND RGEN CARDS
- CSD TELEPHONES
- @SD DATA ADAPTERS (DTA)
- DATA TERMINALS/WORK STATIONS
- EXTERNAL PAGING AMPLIFIER
GTE OMNI SBCS COURSE AND SITE DOCUMENTATION PACKAGE
STANDARD INSTALLATION TOOLS
REVIEW EXERCISE
INSERT AND SEAT PACKAGE B CARDS AND ACTIVATE STRAPPINGOPTION ON RGEN CARD FOR MESSAGE WAITING FEATURE ON
SLT...

Package B Card Installation
POWERSUPPLY
1.
2.GROUND YOURSELF PRIOR TO HANDLING CARDS.
SINCE SYSTEM POWER MUST BE TURNED OFF WHEN INSTALLING OR REPLACING CPMC OR MEMC
CARDS, OFFICE DEPENDENT DATA BASE WILL BE DELETED AND CUSTOMIZED DATA BASE MUST BE
REPROGRAMMED.
3.IF MESSAGE WAITING ON SLT INSTRUMENTS IS REQUIRED, CUT STRAP OR SLIDE SWITCH ON
RGEN CARD.
4.INSTALL CARDS AFFECTED BY PACKAGE B IN DESIGNATED SLOTS:
RGEN - RGEN SLOT
8DTC - SLOTS 00 THROUGH 14 (IF DTA IS INSTALLED, USE SLOTS 00,03,06,09, OR...

Data Terminal Adapter
(DTA) InstallationMASKINGPLATE
1 PROCEDURE1.INSTALLATION OF DATA ADAPTER (DTA) IN CSD TELEPHONE ALLOWS
RS-232-C INTERFACE CONNECTION TO A CUSTOMER-SUPPLIED
TERMINAL OR WORK STATION.
aREFER TO FOLLOWING PAGE FOR DTA INSTALLATION PROCEDURE.
4.33 

-- .Data Adapter (DTA) Installation
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.ENSURE THAT YOU ARE WEARING A GROUNDED ANTI-STATIC WRIST STRAP.
REMOVE THE DTA, AC POWER SUPPLY ADAPTER, TWO GROUNDING WIRES, FIVE
WASHERS, AND THREE SCREWS FROM PACKAGE.
REMOVE UPPER CASE AND MASKING PLATE FROM CSD TELEPHONE.
INSTALL TWO GROUNDING WIRES TO CSD CONTROL CIRCUIT CARD. GROUNDING
WIRE A IS TWO INCHES IN LENGTH AND WIRE B IS EIGHT AND FIVE-EIGHTHS
INCHES IN LENGTH. ATTACH WIRES WITH ONE WASHER AND SCREW, IN
FOLLOWING...

@DIAGRAM REPRESENTS A TYPICAL EXAMPLE OF
CROSS CONNECTIONS FOR A CSD TELEPHONE.
eEACH CSD TELEPHONE REQUIRES ONLY ONE
PAIR OF WIRES FOR TIP AND RING (SIMILAR TO
SLT CROSS CONNECTIONS). ON THE CDF
TERMlNAL BLOCK, ONLY EVERY OTHER PAIR OF
WIRES IS USED.
8EXAMPLE ILLUSTRATES CDF CROSS
CONNECTION FOR AN 8DTC INTERFACE CARD IN
SLOT 00, USING CABLE NUMBER (CN) 0.
CONNECTOR BLOCK SHOWN WOULD HANDLE
ALL EIGHT CIRCUITS FOR 
THE CARD SLOT
IDENTIFIED ABOVE.
.REFER TO CDF CROSS CONNECT REFERENCE
CHART IN OF STUDENT...

Student Notes
4.36 

Data Terminal Installation
POWER CORD
*REQUIRES FOLLOWING PIECES OF EQUIPMENT:
-
-
-CUSTOMER SUPPLIED DATA TERMINAL, WORK STATION, OR
PRINTER
@SD TELEPl-lONE WITH INSTALLED DATA TERMINAL ADAPTER (DTA)
AC POWER SUPPLY ADAPTER
CSD TO DATA TERMINAL CABLE
4.37 

Data Terminal Installation (Continued)
lDESCRlPTlONl (Continued)
@DATA TERMINAL’S RS-232-C PORT PIN CONFlGURATlON MUST BE
COMPATIBLE WITH PIN CONFIGURATION FOR RS-232-C PORT ON CSD
TELEPHONE’S DATA TERMINAL ADAPTER (DTA), AS LISTED BELOW:
0PIN CONFIGURATION
12
3
4
5
6
7
a
9
10
11
12
13
14
15
16
17
18
19
20
21
22
2324
25SIGNALDESCRIPTION
FGTD
RDRTS
CTS
DSR
SG
RLSDST2TRANSMISSION SIGNAL ELEMENT TIMING
DTRDATA TERMINAL READY
RIRING INDICATOR PROTECTIVE GROUND
TRANSMITTED DATA
RECEIVED DATA
REQUEST TO SEND...

Data Terminal Installation (Continued)
IPR~CEDUREICONNECTOR
1.ENSURE THAT DTA IS INSTALLED 
IN
CSD TELEPHONE.TELEPHONE
CORD
2.PLUG DATA TERMINAL POWER
CABLE INTO THE POWER OUTLET.POWER OUTLET
3.CONNECT CSD AND DATA
TERMINAL WITH THE CSD TO DATA
TERMINAL CABLE.
4.39