GoPro Wi Fi Combokit User Manual

							wi-Fi remote: Ways to Wear
ATTACHMeNT  KeY: 
The Attachment Key makes it easy to attach the Wi-Fi 
Remote to your car keys, lanyards, straps, zippers and more. 
To insert the Attachment Key:1.   Insert the Attachment Key into key slot until it clicks.
To remove the Attachment Key:1.  Slide and hold the latch lever in the direction of the arrow, then 
remove the key.
Connecting
wirelessly connect your goPro camera   
to a Wi-f i remote, smartphone, t ablet  
or Wi-f i network.
CONNeCT  HD HeRO2:• Wi-f i remote
• smartphone/t ablet
• w i-Fi network
CONNeCT  ORIGINAl HD HeRO:• wi-Fi remote
20 21
1_ComboKit_UM_ENG-FRA_RevA.indd   20-213/22/12   12:53 PM   
						

							With the Wi-Fi BacPac attached to an HD HERO2 camera, you 
can wirelessly connect, one-at-a-time, to a Wi-Fi Remote, 
Smartphone, Tablet or Wi-Fi Network. The Wi-Fi Remote 
gives you control of up to 50 GoPro cameras simultaneously.
Your Wi-Fi BacPac and Wi-Fi Remote arrive pre-connected in 
the Wi-Fi Combo Kit.  Follow the steps below only to connect 
additional HD HERO2 cameras with Wi-Fi BacPac’s to your 
Wi-Fi Remote or to a new Wi-Fi Remote. 
1.  Put your HD HeRO2 into Connection Mode:a.  Make sure your Wi-Fi BacPac is attached to your 
HD HERO2 camera and both are powered ON.
b.   Short press the POWER/MENU button on the 
Wi-Fi BacPac to enter into the HD HERO2 Wi-Fi 
Menu Screen.
c.  Press SHUTTER/SELECT to enter into the Wi-Fi 
Connection Menu.
d.  
Using the POWER/MODE button, highlight New 
WiFi RC. Then press SHUTTER/SELECT.
e.   The Wi-Fi connection animation will appear 
indicating that the Wi-Fi BacPac is searching for 
a connection. Press SHUTTER/SELECT at any 
time to cancel.
f.  Proceed to next step.
connecting: HD HeRO2 + Remote
connecting: HD HeRO2 + Remote
2.  Put your Wi-Fi Remote into Connection Mode:a. Ensure the remote is powered OFF
b.  On the Wi-Fi Remote, hold down the SHUTTER/
SELECT button while powering it ON.
c.   Release the SHUTTER/SELECT button when you see 
the connecting screen on the Wi-Fi Remote.
3.   If the connection is successfully made, 
you will see the following screen on both 
camera and remote
After, you will be asked if you would like to connect 
to additional cameras, press the SHUTTER/SELECT 
button to select YES, then repeat step one above. 
Otherwise select NO.
4.  If connection was not successful, you 
will see this screen. Please repeat the 
steps above.
TIP:
The Wi-Fi Remote can control up to   
50 GoPro Cameras (Original HD HERO   
and later) at a time from up to   
600ft / 180m away.
22 23
1_ComboKit_UM_ENG-FRA_RevA.indd   22-233/22/12   12:53 PM   
						

							c.  Press SHUTTER/SELECT to enter into the Wi-Fi 
Connection Menu.
d.   Using the POWER/MODE button, highlight 
PHONe&TABleT. Then press SHUTTER/SELECT.
e.  You will immediately see the check box screen. 
Your HD HERO2 camera is now ready to connect 
with your Smartphone or Tablet.
3.   Connect your Smartphone or Tablet to your camera 
and Wi-Fi BacPac:
a. Enter the settings menu for your Smartphone or Tablet.
b. Choose Wi-Fi or Wireless menu.
c.  Select the Wi-Fi BacPac, which will appear named GOPRO-
BP-XXXXXX
d.   You will be prompted to enter the password you configured in Step 1.e.   Confirm your Smartphone/Tablet is now connected to the 
BacPac’s Wi-Fi network.
4.  launch the GoPro App and follow the provided steps.*  Live streaming, video + photo sharing to the web and Bluetooth  
will be available with a future downloadable product update at:  
gopro.com/update
With the Wi-Fi BacPac attached to an HD HERO2 camera, 
you can wirelessly connect, one-at-a-time, to a Wi-Fi 
Remote, Smartphone, Tablet or Wi-Fi Network. The GoPro 
App running on a Smartphone or Tablet enables full camera 
control, preview, playback, live stream and video + photo 
sharing* from one or more HD HERO2 cameras. Visit 
gopro.com for more information on the GoPro App.
Follow the steps below to connect your HD HERO2 camera 
to a Smartphone or Tablet.
1. Set up Wi-Fi BacPac Name and Password:a.   Download and install the latest version at gopro.com/
cineformstudio
b.   Plug in your Wi-Fi BacPac into your computer and launch GoPro 
CineForm Studio software. 
c.   CineForm Studio software will prompt you with information on 
how to set the name and password on your Wi-Fi BacPac.
2.   Put your HD HeRO2 and Wi-Fi BacPac into 
Connection Mode:
a.  Make sure your Wi-Fi BacPac is attached to your HD 
HERO2 camera and both are powered ON.
b.  
Short press the POWER/MENU button on the Wi-Fi 
BacPac to enter into the HD HERO2 Wi-Fi Menu Screen.
connecting: HD HeRO2 + 
Smartphone / Tablet connecting: HD HeRO2 + 
Smartphone / Tablet
24 25
1_ComboKit_UM_ENG-FRA_RevA.indd   24-253/22/12   12:53 PM   
						

							You can connect your HD HERO2 to a Wi-Fi network or 
Hotspot to live stream, share photos + videos and control 
multiple at a time using the GoPro App*.
Follow the steps below to connect your HD HERO2 and  
Wi-Fi BacPac to a Wi-Fi Network for the first time:
1.   Connect your HD HERO2 and Wi-Fi BacPac to your 
Smartphone or Tablet. See steps in the HD HERO2 + 
Smartphone / Tablet section for instructions on how 
to do this.
2.   Using the GoPro App, follow the instructions provided on 
gopro.com/support to complete the Network setup.
*  Live streaming, video + photo sharing to the web and Bluetooth  
will be available with a future downloadable product update at:  
gopro.com/update
connecting: HD HeRO2 + Network
With the Wi-Fi BacPac attached to an Original HD HERO 
camera, you can wirelessly connect to the Wi-Fi Remote. 
The Wi-Fi Remote gives you control of up to 50 cameras at 
a time from a range of up to 600ft/180m.
Your Wi-Fi BacPac and Wi-Fi Remote arrive pre-connected 
in the Wi-Fi Combo Kit. Follow the steps below only if you 
want to connect additional Original HD HERO cameras or 
connect with a new Wi-Fi Remote.
Connecting your Wi-Fi Remote to additional Original HD 
HeRO cameras:
1.   Place your Original HD HeRO with Wi-Fi  BacPac 
into Connection Mode:
a.   Make sure your Wi-Fi BacPac is attached to your 
GoPro camera and powered ON.
b.   Enter the HD HERO camera settings using the 
POWER/MODE button. Press SHUTTER/SELECT to 
enter the Settings Menu.
c.  Toggle to the Wi-Fi Menu using the POWER/MODE 
button. Press SHUTTER/SELECT to enter into the 
Wi-Fi menu.
connecting: Original HD HeRO   
+ Wi-Fi Remote
26 27
1_ComboKit_UM_ENG-FRA_RevA.indd   26-273/22/12   12:53 PM   
						

							d.  Select REMOTE using the SHUTTER/SELECT 
button.
e.  If connection is successful, you will see the 
successful connection screen.
f. If connection fails, restart the process.
2. Place your Wi-Fi Remote into Connection Mode:a. Ensure the remote is powered OFF.
b.   On the Wi-Fi Remote, hold down the SHUTTER/
SELECT button while powering it ON.
c.   Release the SHUTTER/SELECT button when you 
see the connecting screen on the Wi-Fi Remote.
3.   If the connection is successfully made, 
you will see the following screen on 
both camera and remote. 
connecting: Original HD HeRO   
+ Wi-Fi Remoteconnecting: Original HD HeRO   
+ Wi-Fi Remote
After, you will be asked if you would like to 
connect to another GoPro camera. To pair with 
additional cameras, use the SHUTTER/SELECT 
button to select YES, then repeat step one 
above. Otherwise select NO.
4.   If connection was not successful, you 
will see this screen. Please repeat the 
steps above.
28 29
1_ComboKit_UM_ENG-FRA_RevA.indd   28-293/22/12   12:53 PM   
						

							Safety Information
WARNING: Failure to follow these safety instructions could result 
in fire, electric shock, or other injury or damage to the Wi-Fi 
BacPac, Wi-Fi Remote, or other property.
HANDlINGThe Wi-Fi BacPac and Wi-Fi Remote contain sensitive components. 
Do not drop, disassemble, open, crush, bend, deform, puncture, shred, 
microwave, incinerate, paint, or insert foreign objects into either product. 
Do not use the Wi-Fi BacPac or Wi-Fi Remote if it has been damaged—
for example, if the product is cracked, punctured, or damaged by water.
KeePING THe WI-FI ReMOTe’S l CD CleANClean LCD screen immediately if it comes into contact with any 
contaminants that may cause stains, such as ink, dyes, makeup, dirt, 
food, oils, and lotions. To clean the LCD, use a soft, slightly damp, 
lint-free cloth. Avoid getting moisture in openings. Don’t use window 
cleaners, household cleaners, aerosol sprays, solvents, alcohol, 
ammonia, or abrasives to clean LCD.
AVOIDING WATeR AND WeT eNVIRONMeNTS WHeN THe  WI-FI 
BACPAC IS NOT IN HOuSING 
When not protected in the waterhousing, do not use the Wi-Fi BacPac 
in rain, or near washbasins or other wet locations. Take care not to spill 
any food or liquid on the Wi-Fi BacPac. In case the Wi-Fi BacPac gets 
wet, turn off and unplug from camera before cleaning, and allow it to dry 
thoroughly before using again. Do not attempt to dry the Wi-Fi BacPac 
with an external heat source, such as a microwave oven or hair dryer. 
Damage to the Wi-Fi BacPac caused by contact with liquid is not covered 
under the warranty.
Safety Information
WATeR  ReSISTANCe Do not submerge the Wi-Fi Remote in more than 10ft / 3m of water. Do 
not attempt to dry the Wi-Fi Remote with an external heat source, such 
as a microwave oven or hair dryer. Damage to the Wi-Fi Remote caused 
by excessive water pressure is not covered under warranty.
uSING CONNeCTORS AND PORTSNever force a connector into a port. Check for obstructions on the port. 
If the connector and port don’t join with reasonable ease, they probably 
don’t match. Make sure that the connector matches the port and that you 
have positioned the connector correctly in relation to the port.
KeePING THe  WI-FI BACPAC AND WI-FI ReMOTe  WITHIN 
ACCePTABle  TeMPeRATuReS 
The Wi-Fi BacPac and Wi-Fi Remote are designed to be operated in 
temperatures between 0° C and 40° C and stored in temperatures 
between 0° C and 70° C. Extreme temperatures may temporarily affect 
battery life, or affect the functionality of the Wi-Fi BacPac and Wi-Fi 
Remote. Avoid dramatic changes in temperature or humidity when using 
the Wi-Fi BacPac and/or Wi-Fi Remote as condensation may form on or 
within the products. When you’re using the Wi-Fi BacPac, Wi-Fi Remote 
or charging the battery, it is normal for the product to get warm. The 
exterior of the products functions as a cooling surface that transfers heat 
from inside the unit to the cooler air outside.
30 31
1_ComboKit_UM_ENG-FRA_RevA.indd   30-313/22/12   12:53 PM   
						

							GoPro warrants that for a period of one (1) year from original date of 
purchase (or such longer period required by applicable law), the product 
will be free from defects in materials and workmanship under normal 
use. In the event of a defect, contact GoPro at gopro.com/support for 
return instructions. GoPro’s sole obligation under this warranty will be at 
its option to repair or replace the product. This warranty does not apply 
to products damaged by misuse, accident, or normal wear and tear. 
Because of possible user resealing error, this product is not warranted 
against water housing leakage or any resulting damage. The product is 
not designed for or warranted against damage from use in medical or 
other applications requiring fail-safe operation, or in flammable or other 
inherently hazardous environments.
ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR 
A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THIS 
WARRANTY. GOPRO DISCLAIMS ALL OTHER EXPRESS OR IMPLIED 
WARRANTIES OR CONDITIONS. TO THE EXTENT NOT PROHIBITED 
BY LAW, IN NO EVENT WILL GOPRO BE LIABLE FOR ANY LOSS 
OF DATA, REVENUE OR PROFIT, OR FOR ANY SPECIAL, INDIRECT, 
CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, HOWEVER 
CAUSED, ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY 
TO USE THE PRODUCT, EVEN IF GOPRO HAS BEEN ADVISED OF 
THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL GOPRO’S 
LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. 
Some jurisdictions do not allow limitations on how long an implied 
warranty lasts, or the exclusion or limitation of incidental or 
consequential damages, so the above limitations or exclusions may not 
apply to you. This warranty gives you specific legal rights, and you may 
also have other rights which vary by jurisdiction.
limited Warranty
This device complies with part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) This device may not cause harmful interference, and 
(2) this device must accept any interference received, including interference that 
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a\
 Class 
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed 
to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is enc\
ouraged to 
try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to 
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
Under Industry Canada regulations, this radio transmitter may only operate 
using an antenna of a type and maximum (or lesser) gain approved for the 
transmitter by Industry Canada. To reduce potential radio interference to other 
users, the antenna type and its gain should be so chosen that the equiva\
lent 
isotropically radiated power (e.i.r.p.) is not more than that necessary for 
successful communication.
32
1_ComboKit_UM_ENG-FRA_RevA.indd   32-333/22/12   12:53 PM   
						

							For more advanced information  and demo videos,   
visit:  gopro.com/supportWi-Fi Combo Kit
ManUel de l’UtIlIsateUr + 
inFormations sur la garantie
1_ComboKit_UM_ENG-FRA_RevA.indd   34-353/22/12   12:53 PM  
						

							I M P O R TA N T: Avant d’utiliser votre   
Wi-Fi BacPac™ et votre Wi-Fi Remote, 
vous devrez télécharger des mises à   
jour des produits à : gopro.com/update
Wi-Fi Remote + Wi-Fi BacPac
1_ComboKit_UM_ENG-FRA_RevA.indd   36-373/22/12   12:53 PM  
						

							Félicitations pour votre achat du kit combo Wi-Fi 
BacPac + Wi-Fi Remote. Vous pouvez 
maintenant utiliser votre caméra GoPro 
avec des fonctionnalités Wi-Fi et la 
contrôler avec votre Wi-Fi Remote, votre 
smartphone ou votre tablette. Vous 
pouvez diffuser des vidéos en temps 
réel* sur internet et par tager des photos 
et des vidéos sur le Web par tout où vous 
disposez d’une connexion à l’internet.
Wi-Fi BacPac + 
GoPro CameraGoPro App :
Contrôle total de la 
caméra + lecture 
en temps réel et 
relecture des photos 
+ vidéos sur la plupart 
des smartphones et 
des tablettes.
GoPro Remote : 
Contrôlez jusqu’à 50 
caméras à la fois d’une 
distance pouvant aller 
jusqu’à 600 pieds / 
180 mètres (conditions 
optimales). Réseau Wi-Fi :
diffusez des vidéos en temps réel* 
sur internet et partagez des photos 
et vidéos sur Internet partout où vous 
disposez d’une connexion à l’internet. 
* les fonctionnalités de vidéo en temps réel sur internet, de partage de 
photos et de vidéos sur le web ou par bluetooth, pourront bientôt être 
déchargées dans une mise à jour à venir du produit à gopro.com/update  
1_ComboKit_UM_ENG-FRA_RevA.indd   38-393/22/12   12:53 PM