GGP Italy SPA Brush Cutter 1715010650 Operators Manual

ILGSTOŠA UZGLABÅŠANA
Ja ir paredzïts, ka maš¥na
netiks lietota ilgÇk par 2 - 3 mïnešiem, ir jÇveic
dažas darb¥bas, lai izvair¥tos no grt¥bÇm
maš¥nas lietošanas atsÇkšanas laikÇ un no dzi-
nïja permanentiem bojÇjumiem.
•UzglabÇšana
Pirms maš¥nas novietošanas uzglabÇšanÇ:
– Iztukšojiet degvielas tvertni.
– Iedarbiniet dzinïju un darbiniet to minimÇlo
apgriezienu rež¥mÇ l¥dz apstÇšanas, lai tiktu
patïrïta visa tvertnï palikus¥ degviela.
– πaujiet dzinïjam atdzist un no¿emiet sveci.
– Ielejiet sveces atverï...

Dzinïjs  ........................................ 2 taktu ar gaisdzesi
Cilindru apjoms / Jauda
Mod. 31 - 31D ............................... 27,8 cm
3/ 1,1 kW
Mod. 36 - 36D ............................... 32,5 cm3/ 1,3 kW
Mod. 41 - 41D - 41F ..................... 36,3 cm3/ 1,5 kW
Mod. 45P - 45DP - 45FP .............. 44,3 cm3/ 1,9 kW
Mod. 55P - 55DP - 55FP .............. 50,8 cm3/ 2,1 kW
Dzinïja griešanÇs Çtrums minimÇlajÇ rež¥mÇ 
Mod. 31.. - 36.. - 41..  2500-2900 apgriezieni/mintï
Mod. 45.. - 55.....

18 

ENINTRODUCTION1
Dear Customer,
thank you for choosing one of our products. We hope that you will be completely satisfied with this
machine and that it fully meets your expectations. This manual has been compiled in order to provide
you with all the information you need to get acquainted with the machine and use it safely and effi-
ciently. Don’t forget that it is an integral part of the machine, so keep it handy so that it can be con-
sulted when necessary, and pass it on to a further user if you resell...

EN
MAIN COMPONENTS
1. Power unit
2. Drive tube
3. Cutting device
a. Blade with 3 or 4 points
b. Cutting line head
4. Cutting device guard
5. Front handgrip
6. Guard
7. Handlebar
8. Rear handgrip
9. Connection point (of the webbing)
10. Identification plate
11. Webbing
a. single belt
b. double belt
c. harness 
12. Angle transmission
13. Blade protection (for transport)
14. Spark plug
CONTROLS AND REFUELLING 
21. Engine stop switch
22. Throttle trigger
23. Throttle trigger lockout
24. Starter
25. Choke (if...

EN
1)Warning! Danger. The failure to use this
machine correctly can be hazardous for oneself
and others.
2)Read the instruction manual before using the
machine.
3)If you are using the machine every day in nor-
mal conditions, you can be exposed to a noise
level of 85 dB (A) or higher. 
Wear earmuffs or earplugs and a protective hel-
met.
4)Wear gloves and protective footwear!
11)Fuel tank
12)Engine stop switch posi-
tions
a= stopb= run
13)Tuning minimum speed 
14)Choke
15)Primer
16)Correct position of...

EN
A) TRAINING
1)Read the instructions carefully.Become
acquainted with the controls and the proper use
of the machine. Learn how to stop the engine
quickly.
2)
Only use the machine for the purpose for
which it was designed,namely
–cutting grass and non-woody vegetation,using a nylon line (e.g. around the edges of
lawns, flowerbeds, walls, fences and small
grassy areas to tidy up the cutting done using a
mower);
–
cutting tall grass, dry branches, twigs and
woody shrubsof up to 2 cm diameter, with the...

ground that does not guarantee stability for the
operator;
–never run, but walk carefully paying attention to
the lay of the land and any eventual obstacles;
–assess the potential risks of the ground to be
mown and take all necessary precautions to
ensure your own safety, especially on slopes or
on bumpy, slippery or unstable ground;
–work along the contour on slopes, never when
walking up or down and always keep downhill
of the cutter.  
4) Make sure the machine is securely locked
when you start the...

The machine is supplied with
some of the components disassembled and the
fuel tank empty.  
Always wear strong work
gloves to handle the cutting devices. Mount
the components very carefully so as not to
impair the safety and efficiency of the
machine. If in doubt, contact your dealer.
1. COMPLETING THE MACHINE
1a. “MONO” models
•Model 31 (Fig. 1)
–Fit the front handgrip with guard (1) on the
drive tube (2) using the cap (3), screws (4) and
nuts (5) inserted into their specific seatings.
–Before...

•3 or 4-point blade  (Fig. 6)
ear protective gloves and
fit the blade guard.
–Remove the blade (if fitted) as described in
paragraph 3.
–The guard (1) is fixed to the angle transmission
(2) by two screws (3).
•Cutting line head  (Fig. 7)
When using the cutting
line head the additional guard, with line cut-
ting knife, must always be fitted.  
–Remove the blade (if fitted) as described in
paragraph 3.
–The guard (1) is fixed to the angle transmission
(2) by two screws (3).
–Fit the additional guard (4),...