Getnet Router GA-324WA User Manual

GA-324WA User Manual 
3.5.6   ACL 
Choose Service > ACL. The page shown in the following figure appears. 
 
 
The following table describes the parameters and buttons of this page: 
Field Description 
Direction Select Select the router interface. You can select LAN  or 
WAN . 
LAN ACL Switch Enable or disable ACL. 
IP Address 
Enter the IP address of the specified interface. Only 
the IP address that is in the same network segment 
with the IP address of the specified interface can 
access the router....

GA-324WA User Manual 
3.6   Advance 
In the navigation bar, choose Advance. The  Advance  page that is displayed 
contains  Bridge Setting , Routing, Port Mapping , QoS, SNMP, and Others . 
3.6.1   Bridge Setting 
Choose Advance  > Bridge  Setting . The page shown in the following figure 
appears. This page is used to configure t he bridge parameters. In this page, you 
can change the settings or view some information in the bridge mode and its 
attached ports. 
 
The following table describes the...

GA-324WA User Manual 
 
3.6.2   Routing 
Choose Advance  > Routing . The Routing  page that is displayed contains 
Static Route and RIP . 
3.6.2.1 Static Route 
Click Static Route  in the left pane. The page shown in the following figure 
appears. In this page, you can configure  the routing information. You can add or 
delete IP routes. 
 
The following table describes the parameters and buttons of this page: 
60 
Field Description 
Enable Select it to use static IP routes. 
Destination Enter the IP...

GA-324WA User Manual 
Field Description 
Subnet Mask Enter the subnet mask of the destination device. 
Next Hop Enter the IP address of the next hop in the IP route to the 
destination device. 
Metric The metric cost for the destination. 
Interface The interface for the specified route. 
Add Route Click it to add the new static route to the table. 
Update Select a row in the table to populate the configuration 
fields with that row’s values. Make any necessary 
changes to those values and click it  to...

GA-324WA User Manual 
to select the interfaces on your devices that use RIP, and the version of the 
protocol used. 
 
 
The following table describes the parameters and buttons of this page: 
Field Description 
RIP Select On, the router communicates with other 
RIP-enabled devices. 
Apply Click it to save the settings of this page. 
Interface The router interface that uses RIP. 
Recv Version The interface type to accept RIP messages. You can  choose  RIP1, RIP2 , or Both . 
  Choose RIP1  indicates the...

GA-324WA User Manual 
Field Description 
Add Click it to add the RIP interface to the Rip Config Table.
Delete Select a row in the Rip Config Table and click it to 
delete the row. 
Rip Config Table A list of the router interfaces that enble RIP. 
 
3.6.3   Port Mapping 
Choose  Advance  > Port Mapping . The page shown in the following figure 
appears. In this page, you can bind the WAN interface and the LAN interface to 
the same group. 
 
 
The procedure for manipulating  a mapping group is as...

GA-324WA User Manual 
Step 2 Select a group from the table. 
Step 3 Select interfaces from the WAN and LAN interface list and add them to 
the grouped interface list using the arrow buttons to manipulate the 
required mapping of the ports. 
Step 4  Click Apply  to save the changes.  
3.6.4   QoS 
Choose Advance > QoS . The page shown in the following figure appears. 
Entries in this table are used to assign the precedence for each incoming packet 
based on physical LAN port, TCP/UDP por t number, and...

GA-324WA User Manual 
65 
Field Description 
IP QoS You can choose disable or enable . By default, IP QoS 
is disabled. 
You need to enable IP QoS, and then you can set the 
parameters in this page. 
QoS Policy You can choose  stream based, 802.1p based , or 
DSCP based . 
Schedule Mode You can choose  strict prior or WFQ (4:3:2:1) . 
Src IP The IP address of the source data packet.   
Src Mask The subnet mask of the source IP address. 
Src Port The port of the source data packet. 
Dest IP The IP...

GA-324WA User Manual 
3.6.5   SNMP 
Choose Advance  > SNMP. The page shown in the following figure appears. 
 
 
The following table describes the parameters and buttons of this page: 
Field Description 
Trap IP Address Enter the IP address of trap host. The trap 
information is sent to the host. 
Community name 
(read-only) 
The common character string that is used for 
obtaining the device information. It is like 
password, through which SNMP application 
entry obtains the device information...

GA-324WA User Manual 
 
3.7   Admin 
In the navigation bar, choose Admin. The Admin  page that is displayed contains 
Commit/Reboot , Upgrade, System Log , Password, and Time Zone. 
3.7.1   Commit/Reboot 
Choose Admin  > Commit/Reboot. The page shown in the following figure 
appears. In this page, you can set the router reset to the default settings or set 
the router to commit the current settings. 
 
 
The following table describes the parameters of this page: 
Field Description 
Factory Default...