Home > Gammill > Software > Gammill Creative Studio 6.0 Manual

Gammill Creative Studio 6.0 Manual

Here you can view all the pages of manual Gammill Creative Studio 6.0 Manual. The Gammill manuals for Software are available online for free. You can easily download all the documents as PDF.

Page 201

Phase 4 - Backgrounds201
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 201   |  Page Quilting the Quilt - Which CS Feature To use
E2E (Edge_To_Edge)Pantographs
quilt length by this amount. Also it is a good idea to reduce the length a little to
accommodate shrinkage caused by the quilting. This could be from 1% to 5%,
depending on the fabrics, batting and quilting density. 
Prep Step #2
) Load the quilt and baste the outer edges. 
Prep Step #3)...

Page 202

Getting Started with CreativeStudio®
202
 
Tip: When basting the top edge of the quilt, use the Horizontal Channel Lock to
keep the baste line perfectly straight and square. Then, use this as a guide for
the E2E baseline (first two clicks).  
2.  Enter the quilt length
  in the E2E Settings area. Increase the actual
measurement if the pattern will be stitching off the top & bottom edges of the quilt (or
will be trimmed to fit).  Decrease the actual measurement to adjust for top and
bottom margins and...

Page 203

Phase 4 - Backgrounds203
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 203   |  Page Quilting the Quilt - Which CS Feature To use
E2E (Edge_To_Edge)Pantographs
*  Alternating
 –  allows staggered rows. Examples are included in the next section.
- None means don ’t stagger the rows.
- Plus Row On Top means one extra repeat will be added to the first row and 
every other row.   - Minus Row On Top means one repeat is taken away from the first row and...

Page 204

Getting Started with CreativeStudio®
204
- Teal green  means the patterns wont fit in the current quilting space so CS cant
quilt them yet. 
As mentioned, adjusting patterns that nest should be done before any quilting
begins. Just select all the patterns at once (Select All icon) and reposition as
needed. If adjustments are needed after the first rows have been completed, the
non-quilted patterns need to be selected together. This can be done by holding
down the Ctrl key and clicking on each pattern...

Page 205

Phase 4 - Backgrounds205
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 205   |  Page Quilting the Quilt - Which CS Feature To use
E2E (Edge_To_Edge)Pantographs
7.   Follow one of the steps listed below. 
7a.  Registration: End Of Set
: 
* CS prompts you to Pull up bobbin thread, and Click OK to complete stitching. 
There are no additional prompts because this method uses the endpoint of the last
row completed. 
7b.  Registration: Place Two Pins
: 
*...

Page 206

Getting Started with CreativeStudio®
206
* CS prompts you to Pull up bobbin thread, and Click OK to complete stitching. 
There are no additional prompts because this method uses the startpoint and
endpoint of the last row completed as the two registration points. 
8.  Roll the quilt 
(baste the sides, check the bobbin, etc.)  It is also a good idea to
check that the quilt is still square. Use the  channel lock to check that both
registration marks are on the same horizontal line.
Tip:  
When rolling the...

Page 207

Phase 4 - Backgrounds207
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 207   |  Page Quilting the Quilt - Which CS Feature To use
E2E (Edge_To_Edge)Pantographs
One nice feature about End of Set Continue is that the continue process can be run
as many times as needed to get the patterns advanced as needed.
Continue to Step 11.  
10b. If you chose Registration = Place Two Pins:  
* CS prompts for left registration mark. Move the machine head to the...

Page 208

Getting Started with CreativeStudio®
208
1. Move the machine head back as far as it will go (against the pick-up roller). Now
look at the screen. Do any of the black patterns extend above the crosshair line? If
so, use the Edit / Undo command (Ctrl +z) to backup prior to clicking E2E Continue.
By doing this, you can roll back the quilt so it is positioned properly, and start back
at step 9. 
2. Check the other three edges of the quilting space. Move the machine head to the
left margin, the right margin...

Page 209

Phase 4 - Backgrounds209
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 209   |  Page Quilting the Quilt - Which CS Feature To use
E2E (Edge_To_Edge)Pantographs
Tip:  
If you notice that the bottom corners of the quilt flare out or pull in, you can
include the sides when  you Select points along bottom of E2E. Just be sure that
the 2 registration marks are clicked first, and then it doesnt matter how many other
points are clicked. Press Stop when...

Page 210

Getting Started with CreativeStudio®
210
2. The quilt is rolled before the registration points are marked. When this happens,
the quilt and the screen become out of synch. 
* Roll the quilt back to its previous position.
* Verify the position using the crosshair. To do this, move the machine head until the
crosshair on the screen is positioned at the last stitch sewn as shown on the screen.
Now adjust the quilt until the needle is directly over the last stitch sewn on the quilt.  
*  Restart
 the last...
Start reading Gammill Creative Studio 6.0 Manual
All Gammill manuals