Gammill Creative Studio 6.0 Manual

Quick Ref Panto using E2E251
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 251   |  Page Quick Reference Sheets
 
The top edge is the baseline which is used to square up the patterns. The pattern in the
example has irregular edges which make it nest nicely. However, the pattern will stitch off of
the edge when positioned to eliminate the side gaps. The Trim-Inside  function can be used
to trim off the excess - just make sure to include the extra...

Getting Started with CreativeStudio®
252
Feature: Edge To Edge - Continue  
Assumptions:  The first section (or more) is done, the registration points have been marked
and the quilt has been rolled. 
  9. Click EdgeToEdge_Continue 
10. CS prompts for left and right registration marks. 
11. Check the screen and adjust if needed. 
12. Click Quilt. The first row of the new section now begins.  At the end of the row, CS stops, prompts for bobbin pull-up, Click OK. 
Repeat each row until the entire current...

Quick Ref P2P Line253
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 253   |  Page Quick Reference Sheets
 
5.8 Quick Ref P2P Line
Feature: Point To Point - Line
Point to point describes a CS process where a series of connected line segments are
positioned and stitched. The quilter clicks the points and CS stitches a perfect line between
each contiguous pair. Each  ‘point’ is identified by moving the sewing head to each point (in
order) and pressing...

Getting Started with CreativeStudio®
254
5.9 Quick Ref P2P Pattern
Feature: Point To Point - Pattern
Point to point describes a CS process where a series of patterns are positioned and
stitched. The quilter clicks the points and CS stitches a pattern between each contiguous
pair. Each  ‘point’ is identified by moving the sewing head to a spot on the quilt top (in order)
and pressing the OK button. 
Prep Step #1 - Optional -  Define boundaries to check the P2P placement. 
Prep Step #2. Choose a pattern....

Quick Ref P2P Pattern255
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 255   |  Page Quick Reference Sheets
 Check it before stitching.
5.  Click on Start_Quilting
   and the sewing head moves to the Start of the pattern and CS
prompts for the bobbin pull-up.  Press OK
 when ready to quilt. At the end of the quilting
sequence you will be prompted to pull up the bobbin thread and click OK.  Be sure to
click OK because it completes this process.
Design...

Getting Started with CreativeStudio®
256
5.10 Quick Ref Trim Inside
Feature: Trim Pattern - Inside 
Steps to follow:
1.  Click on the Boundary icon   
 and follow the prompts to define the boundary of the
background area. If the  project were to fill the background of an appliqued block, this would
be the outer edges of the block.  
 
2.  Move the background filler pattern in.
 
Use Pattern_to_Boundary 
   or Repeat Patterns     depending on how many repeats
are needed to fill the area. This example...

Quick Ref Trim Outside257
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 257   |  Page Quick Reference Sheets
 
5.11 Quick Ref Trim Outside
Feature: Trim Pattern - Outside   
Assumptions: This assumes that the following preparation steps have been completed.  Prep Step #1. Click on Boundary icon. Define the boundary and finish by pressing Stop.
Prep Step #2. Highlight the pattern to be used.
Prep Step #3. Click on Pattern into Boundary icon. When the...

Getting Started with CreativeStudio®
258
5.12 Quick Ref Right Click Options
The Right Click Options appear when selected patterns are Right Clicked. Options
presented depend on the patterns selected. 
   
Reposition Options  - 
Rotate
  - rotates the pattern as many degrees as you like. 
Flip Horizontally
 - turns the pattern sideways. 
Flip Vertically
 - turns the pattern upside down.
Mirror
 - creates a mirror image, using any rotation axis defined by the prompts. 
Rubber Stamp
 - makes an exact copy...

Quick Ref Right Click Options259
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 259   |  Page Quick Reference Sheets
 Circular Array
 - creates a new circular pattern by repeating and rotating a single
pattern. CS only needs to know which pattern to use, how many repeats are needed, how
many degrees between each repeat and where the center should be placed. 
Echo Pattern
 - means CS creates a new pattern that is an outline of the original.
The number...

Getting Started with CreativeStudio®
260
  Export Patterns
 - saves the new design for future use as a special CS file type. 
 
Selecting multiple patterns and then exporting them will result in one exported pattern, not
multiples. Use Virtual Stitchout (F2)  before exporting
 to make sure the new pattern will
stitch out in one continuous line design. G ive the pattern a descriptive name.
Node Mode (F7) 
displays the pieces of each pattern, showing all nodes. Endpoint
Nodes are pink squares and are used...