Gammill Creative Studio 6.0 Manual

Restart231
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 231   |  Page Quilting the Quilt - Which CS Feature To use
Manual Stops and Restarts
3A.  Find the restart point 
using the sewing head  -  move the machine until the
needle is just above the point where you want to continue stitching.  Press “Use
This Pt ” on the keypad. CS moves to the closest stitch and waits for another
response. If it looks good,  Press Quilt
 and continue to sew. If not,...

Getting Started with CreativeStudio®
232
4.7 Utility Functions
Utility Functions  are  used in many different techniques. They are very important, but
not used on a regular basis. 
4.7.1 Technical SupportThere are many mechanical, electrical, and numeric default settings that are
required to run CS. The defaults are the initial values that are set every time CS
starts up. Many of these values can be  changed as needed
 during the quilting
session. Others are considered Restricted Areas and should  not...

Utility Functions233
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 233   |  Page Quilting the Quilt - Which CS Feature To use
Technical Support
Each setting in the configuration form is explained thoroughly in the section Quilting
The Quilt ,  Set Stitching Defaults
. 
Diagnostic testing can be done when troubleshooting is warranted. This should only
be done when following the instructions of an authorized Gammill / Statler
technician. 
The remaining...

Getting Started with CreativeStudio®
234
climates may require this to be done more frequently.  
4.7.4 Calibrate All
Calibrating guarantees stitching accuracy. This doesn ’t need to be done often but
can be performed as needed. The Calibrate All routine is called automatically after
loading new software, and all three sub calibrations are performed.  
Click on Tools and Click on Calibrate All
There may be occasions to calibrate only one of the features. In this case, Click on
Tools, and hover over the...

Utility Functions235
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 235   |  Page Quilting the Quilt - Which CS Feature To use
Calibrate All
power making it easier to move. 
Power Assist needs to be adjusted by each individual until the touch is comfortable.
There is a calibration utility that determines the initial default settings. It also allows
additional adjustments, making it feel right.  
Calibrate Power Assist  - allows you to adjust the...

Getting Started with CreativeStudio®
236
As a safety feature, CS turns off the Power Assist before it accepts the new settings.
So, you will need to click the Test Power Assist button every time you want to adjust
the settings.
Step 4. Activate the Power Assist Utility. 
Calibrating the Power Assist does not turn it on automatically, so click on the Power
Assist choice in the Tools section of the command  bar. Once it is turned on, PA will
remain on until it is turned off, even if CS is shut down and...

Utility Functions237
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 237   |  Page Quilting the Quilt - Which CS Feature To use
Calibrate All
When the routine is done, click OK to clear the message.  

Part V 

 239
Gammill, Inc. | 2015             M-S-0001 - CreativeStudio 6.0 User Manual -  Rev 00                 239   |  Page Quick Reference Sheets
 
5 Quick Reference Sheets
5.1 Quick Ref Icons ShortcutsCreativeStudio ® Quick Start Icons and Shortcuts
Stitching Icons:      ü   
is an abbreviation for click   
   
Icon Icon Name - description &  shortcut keystrokes included.
Tip - Created for the documentation only
DIY - Design It Yourself - Tips on pattern design and shortcuts.- 
Boundary -  Begins the...

Getting Started with CreativeStudio®
240
Quick Reference Icons for Projects:
The project content can be changed using these icons.
Icon Icon Name & location
Save (Project) -  Saves the current project
Add Pattern  - Starts the process for adding patterns
Delete Pattern -  Deletes the selected pattern
Check Project Details -  Displays the Project Details dialog box
Add Quilt Group -  Creates a new Quilt Group Tab
Remove Quilt Group -  Removes the current Quilt Group Tab
Undo - Reverses the last...