Fujitsu P42vha20 Users Manual

E-11
English
PUTTING BATTERIES IN THE REMOTE CONTROL
1To remove the cover, slide it
outwards while pressing it down.2Place two AA batteries in the
remote control.  Make sure that the
batteries are properly oriented.3Close the cover until it snaps into
place.
Note
The remote control will not function properly if the batteries are dead.  Be sure to replace them as needed.
Do not use rechargeable batteries (Ni-Cd).
CAUTION:Be sure to use replacement batteries of the same type as the original ones.
When...

E-12
EFFECTIVE RANGE FOR THE REMOTE CONTROL
Point the remote control at the display’s signal receiver when using it.
Make sure that there are no obstacles between the remote control and the display’s signal receiver.
USING THE REMOTE CONTROL (Continued)
Information
The remote control may not function properly if you use a high-frequency fluorescent lamp.  If you experience problems, move the lamp or use the
remote control from a different position.
Display – frontDisplay – side
Right Left
5 m...

E-13
English
CONNECTING THE DISPLAY TO EXTERNAL EQUIPMENT
Be sure to turn OFF the power to the display and external equipment before making any connections.
No cables are supplied with the display for connection to external equipment.  The type of cable to be used varies depending on the PC
model.  Contact your dealer for more information.
RECEPTACLE
Make sure that the power cable’s grounding wire is grounded.
The display comes with a 3-prong power plug; one prong is connected to the grounding wire.  If...

E-14
CONNECTING THE DISPLAY TO EXTERNAL EQUIPMENT (Continued)
EXAMPLE OF CONNECTION TO EXTERNAL COMPONENTS
Remote
control DisplaySpeaker (optional)
Speaker
VCR or other external components See P. 
VCR E-15
DVD player 
Satellite tuner E-17
PC E-18

&17)&07	@
03.1.16, 11:50 Page 14EPCF
1BHF.BLFS
+11$
 

English
E-15
VCR
• Connect the video signal cable to the SCART terminal. (When the P-TE1000E is installed.)
• Connect the video signal to either the S-video input terminal or the video input terminal. (When the P-TE1010E is installed.)
To SCART output
To SCART input
An example of the underside of the display
(with the P-TE1000E installed in the P42VHA10)
Note
• Unplug the power cord from the AC outlet before you connect external components.
• Also refer to the instructions for the component to be...

E-16
CONNECTING THE DISPLAY TO EXTERNAL EQUIPMENT (Continued)
DVD PLAYER
•Connect the video signal cable to either the component video terminal or the SCART terminal. (When the P-TE1000E is installed.)
•Connect the video signal cable to the component video input terminal, S-video input terminal, or the video input terminal. (When the P-
TE1010E is installed.)
•If the component to be connected is equipped with component video output terminal, it is recommended to connect to the component video
terminal....

English
E-17
SATELLITE TUNER
•Connect the video signal cable to either the component video terminal or the SCART terminal. (When the P-TE1000E is installed.)
•Connect the video signal cable to the component video input terminal, S-video input terminal, or the video input terminal. (When the P-
TE1010E is installed.)
•If the component to be connected is equipped with component video output terminal, it is recommended to connect to the component video
terminal.
Note
•Unplug the power cord from the AC...

E-18
 PC
•As the cable for connecting a PC differs with the PC model, please consult your dealer for information on the right cable to purchase.
•The PC can be connected to either the front side or the rear side, whichever is most convenient.
To RGB output (mD-sub)
To audio outputTo RGB output (DVI-D)
To RGB1 input
(DVI-D) To audio inputTo RGB2
input
(mD-sub)
Note
•Unplug the power cord from the AC outlet before you connect external components.
•Also refer to the instructions for the component to be...

English
E-19
* You can also use the buttons
on the display’s control
panel to perform these steps.
 TURNING THE POWER ON AND OFF
1
2
3
Press /I to the left at the bottom
of the display.
The power lamp lights up.
Press  on the remote control.
The colour of the power lamp changes from “Red”
to “Green”.
Press  –  or  –  or
.
Select the video mode to be input.
Press  when the power is ON.
The colour of the power lamp changes from
“Green” to “Red” and the power turns “OFF”.
Press the Volume button
Press  to...

E-20
SELECTING INPUT MODE
RGB INPUT MODE
1
RGB1 mode
Press the  –  buttons to
select the input mode.
You can select from VIDEO1 mode to VIDEO4
mode.
The video modes corresponding to each input
terminal are as follows.
•VIDEO1: SCART (when P-TE1000E is
installed), Video (when P-TE1010E is installed)
•VIDEO2: S-Video (when P-TE1010E is
installed)
•VIDEO3: Comp. video (when P-TE1010E is
installed)
•VIDEO4: Comp. video
* For selection of the input terminal, see
“SETTING THE INPUT TERMINALS” on
P. E-36.
* You...