Fujitsu Myrica P42 2 User Manual

							  MYRICA P42-1A / P42-2 / P50-2 
A26361-K1040-Z120-1-M119, edition 3  English - 39 
Norway B/G PAL Nicam  
Country TV Colour Stereo Subtitles 
Poland D/K PAL  Teletext 
Portugal B/G PAL  Teletext 
Rumania G PAL   
Russia D/K SECAM   
Saudi Arabia  B  SECAM     
Slovakia  D/K  SECAM / PAL     
Slovenia B/H PAL   
South Africa  I  PAL     
Spain B/G PAL Nicam Teletext 
Sweden B/G PAL Nicam Teletext 
Switzerland B/G PAL FM-FM Teletext 
Tunesia B SECAM   
Turkey B PAL  Teletext 
United Arab Emirates  B/G  PAL     
United Kingdom  I  PAL  Nicam  Teletext 
 
 
						

							MYRICA P42-1A / P42-2 / P50-2 
40 - English A26361-K1040-Z120-1-M119, edition 3 
Troubleshooting 
Should an error occur, first check the following points. If the distortion is still not eliminated, the 
plasma TV should, if possible,  be checked on another signal source  and/or with another data cable.  
If you are unable to solve the problem, please inform our help desk. 
Having this problem?  Check the following points: 
No display (power indicator does not light)  ►  Check whether the power cable of the 
device is properly plugged in and the 
ON/OFF switch on the back of the device 
is switched on. 
Display becomes darker  The phos phorous illumination has a limited 
lifetime. If your screen display should become 
too dark, it will have to be exchanged. 
►   Please contact our help desk. 
Permanently unlit or lit pixels  The  standard of production techniques today 
cannot guarantee an absolutely fault-free 
screen display. A few isolated constant lit or 
unlit pixels may be present. The maximum 
permissible number of this kind of defective 
pixels is dependent on the resolution: 
MYRICA P42-1A/P42-2: 6L / 10D / 10T 
MYRICA P50-2: 8L / 14D / 14T 
L = light, D = dark, T = total 
No picture (power indicator glows orange)  ►  Switch on the plasma TV on the device or 
with the remote control. 
►   Check the setting of the picture signal 
source. 
The remote control does not work.  ►  Check whether the batteries in the remote 
control are still sufficiently charged. 
►   Make sure that the sensor for the remote 
control on the plasma TV is not exposed 
to strong light. 
 
 
						

							  MYRICA P42-1A / P42-2 / P50-2 
A26361-K1040-Z120-1-M119, edition 3  English - 41 
Troubleshooting in TV mode 
Having this problem?  Check the following points: 
No sound ►  Check the volume setting. 
►   Check whether the device is muted. 
No picture, only static  ►  Check that the antenna cable is correctly 
connected. 
Reception may be poor. 
The picture is fuzzy.  ►  Check that the antenna cable is correctly 
connected. 
Reception may be poor. 
The picture has dark interference lines and a 
strong humming sound can be heard.  There may be an interference signal on the 
antenna cable. 
►
  Have the installation checked. 
A sheath current filter from the accessories 
trade can provide a remedy. 
The picture has shadows or ghost images  ►  Check the antenna cable. 
Use a directional antenna instead of an 
omnidirectional antenna. 
The picture shows interference, false colours or 
line and picture shaking.  ►
  Check whether the plasma TV is set to 
the correct TV system (PAL or SECAM). 
 
 
						

							MYRICA P42-1A / P42-2 / P50-2 
42 - English A26361-K1040-Z120-1-M119, edition 3 
Troubleshooting in PC mode 
Having this problem?  Check the following points: 
Message: 
No Signal / Keine Eingabe ►
  Check the setting of the picture signal 
source. 
►   Check whether the antenna or data cable 
is correctly connected. 
Message: 
Out of range   The input signal (horizontal frequency and 
refresh rate) at the displayed input does not 
correspond to the technical plasma TV data.  
►
  Adjust the video frequency range using 
the computer software (see 
documentation for your computer or your 
graphics card). 
Picture position is not correct  The  plasma TV recognises an undefined mode 
(see Preset operating modes (PC)). 
►   Use the OSD function  Geometry/Auto  to 
carry out the self-adjustment of the 
plasma TV. 
►   Set the picture position with the OSD 
menu. 
These functions are  only available when PC is 
selected as the signal source. 
Picture is shaking  ►  Check whether the data cable for the 
plasma TV is correctly attached to the 
monitor port on the computer.