Fujifilm Camera X30 Owners Manual

Insert the battery.
Using the battery to keep the battery latch pressed to one side, insert the battery contacts
first in the direction shown by the arrow. Confirm that the batte ry is securely latched.
Insert the battery in the orientation shown. Do not use force or attempt to insert
the battery upside down or backwards.  The battery will slide in easily in the
correct orientation.
2. 
Arrow
Battery latch
Inserting the Battery and a Memory Card
002D0020 003400310020 002D  

Insert the memory card.
Holding the memory card in the orientation shown, slide it in u ntil it clicks into place at the
back of the slot.
Be sure card is in the correct orientation; do not insert at an  angle or use force. If the
memory card is not correctly inserted or no memory card is inse rted,   will appear
in the LCD monitor and internal  memory will be used for recording and playback.
3. 
Close the battery-chamber cover.4. 
Inserting the Battery and a Memory Card
002D0020 003400320020 002D  

Removing the Battery and Memory Card
Before removing the battery or memory card, turn the camera off  and open the battery-
chamber cover.
To remove the battery, press the  battery latch to the side, and slide the battery out of the
camera as shown.
To remove the memory card, press it in and release it slowly. The card can then be removed
by hand. When a memory card is removed, the card could come out  of the slot too quickly.
Use your finger to hold it and gently release the card.
Inserting the Battery...

The battery is not charged at shipment. Charge the battery befo re use. The camera charges the
battery internally.
The camera uses an NP-95  rechargeable battery.
The battery takes about 4 hours  and 30 minutes to fully charge.
Attach the plug adapter to the AC power adapter.
Attach the plug adapter as shown , making sure that it is fully inserted and clicks into place
on the AC power ad apter terminals.
The plug adapter is exclusively for use with the supplied AC po wer adapter. Do not
use it with other...

Charge the battery.
Connect the camera to the supplied AC power adapter using the supplied USB cable. Then
plug the AC power adapter into an indoor power outlet.
Be sure the connectors are in th e correct orientation and then insert them fully.
2. 
Charge status
The battery status icons show ba ttery charge status when the camera is turned on, and the
indicator lamp shows it when the camera is turned off.
Battery status icon when
camera on Indicator lamp when
camera off
Battery status
 (yellow) On Battery...

The battery will not charge while the camera is in the shooting mode.
Remove dirt from the battery terminals with a clean, dry cloth. Failure to observe this
precaution could prevent the battery from charging.
Do not affix stickers or other objects to the battery. Failure to observe this precaution could
make it impossible to remove t he battery from the camera.
Do not short the battery terminals. The battery could overheat.
Read the cautions in “The Battery and Power Supply”.
Use only battery chargers...

To turn the camera on, rotate the zoom ring as shown. Rotate the zoom ring to [OFF] to turn the
camera off.
Press the   button to start playback. Press the shutter button h alfway to return to
shooting mode.
The camera will turn off automatically if no operations are perf ormed for the length of time
selected for  [POWER MANAGEMENT]  > [AUTO POWER OFF]  in the setup menu. To
reactivate the camera after it h as turned off automatically, pre ss the shutter button halfway
or turn the camera on after rotating...

Battery Level
After turning the camera on, check the battery level in the display.
Battery close to fully charged.
Battery about two-thirds charged.
Battery about one-third charged. Charge as soon as possible.
(red) Battery exhausted. Turn came
ra off and recharge battery.
Turning the Camera on and Off
002D0020 003400380020 002D  

A language-selection dialog is displayed the first time the camera is turned on. Set up the camera
as described below (you can rese t the clock or change languages at any time using the
[DATE/TIME]  or []  options in the setup menu).
Using the Selector
Press the selector up, down, left, or right to highlight items  and press [MENU/OK] to select.
Move cursor up
Move cursor right
Move cursor down
Move cursor left
Select highlighted item
Basic Setup
002D0020 003400390020 002D  

[POWER SAVE]
[HIGH PERFORMANCE]
Turn the camera on.
1. 
Highlight a language and press [MENU/OK].
Press 
[DISP/BACK]  to skip the current step. Any steps you skip will be displayed  the
next time the camera is turned on.
2. 
The date and time will be displa yed. Press the selector left or right to highlight the year,
month, day, hour, or minute and  press up or down to change. To change the order in which
the year, month, and day are displayed, highlight the date form at and press the selector up
or...