Ford Explorer 2017 Owners Manual
Have a look at the manual Ford Explorer 2017 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 41 Ford manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
TOWING A TRAILER WARNING Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of your vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury. Note: Do not exceed the GVWR or the GAWR specified on the certification label. See Recommended Towing Weights (page 239). Your vehicle may have electrical items, such as fuses or relays, related to towing. See Fuses (page 262). Your vehicle's load capacity designation is by weight, not by volume, so you cannot necessarily use all available space when loading a vehicle or trailer. Towing a trailer places an extra load on your vehicle's engine, transmission, axle, brakes, tires and suspension. Inspect these components periodically during, and after, any towing operation. Load Placement To help minimize how trailer movement affects your vehicle when driving: • Load the heaviest items closest to the trailer floor. • Load the heaviest items centered between the left and right side trailer tires. • Load the heaviest items above the trailer axles or just slightly forward toward the trailer tongue. Do not allow the final trailer tongue weight to go above or below 10-15% of the loaded trailer weight. • Select a ball mount with the correct rise or drop. When both the loaded vehicle and trailer are connected, the trailer frame should be level, or slightly angled down toward your vehicle, when viewed from the side. When driving with a trailer or payload, a slight takeoff vibration or shudder may be present due to the increased payload weight. Additional information regarding proper trailer loading and setting your vehicle up for towing is located in another chapter of this manual. See Load Limit (page 232). You can also find information in the RV & Trailer Towing Guide available at your authorized dealer, or online. 238 Explorer (TUB) Canada/United States of America, enUSA, Edition date: 03/2016, First Printing Towing
RV & Trailer Towing Guide Online http://www.fleet.ford.com/towing-guides/ Website TRAILER SWAY CONTROL (If Equipped) WARNING Turning off trailer sway control increases the risk of loss of vehicle control, serious injury or death. Ford does not recommend disabling this feature except in situations where speed reduction may be detrimental (such as hill climbing), the driver has significant trailer towing experience, and can control trailer sway and maintain safe operation. Note: This feature does not prevent trailer sway, but reduces it when it begins. Note: This feature cannot stop all trailers from swaying. Note: In some cases, if your vehicle speed is too high, the system may turn on multiple times, gradually reducing your vehicle speed. The system applies the brakes to the individual wheels and reduces engine torque to aid vehicle stability. If the trailer begins to sway, the stability control warning lamp flashes and a message appears in the information display. See Information Messages (page 113). Slow your vehicle down, pull safely to the side of the road and check for correct load distribution. See Load Carrying (page 230). You can switch this feature off in the information display. When you switch the ignition on, the system automatically turns on. RECOMMENDED TOWING WEIGHTS Note: Do not exceed the trailer weight for your vehicle configuration listed in the chart below. Note: Be sure to take into consideration trailer frontal area. Do not exceed 20 feet² (1.86 meters²) if your vehicle can tow a class I trailer or 40 feet² (3.72 meters²) if your vehicle can tow a class III trailer. Note: For high altitude operation, reduce the gross combined weight by 2% per 1000 feet (300 meters) starting at the 1000 foot (300 meter) elevation point. Note: Certain states require electric trailer brakes for trailers over a specified weight. Be sure to check state regulations for this specified weight. The maximum trailer weights listed may be limited to this specified weight, as the vehicle ’s electrical system may not include the wiring connector needed to activate electric trailer brakes. 239 Explorer (TUB) Canada/United States of America, enUSA, Edition date: 03/2016, First Printing Towing
Your vehicle may tow a trailer provided the maximum trailer weight is less than or equal to the maximum trailer weight listed for your vehicle configuration on the following chart. Maximum trailer weight Maximum GCWR Engine 2000 lb (907 kg) 6900 lb (3130 kg) 2.3L GTDI 2WD 1 2000 lb (907 kg) 6900 lb (3130 kg) 3.5L TiVCT 2WD 1 3000 lb (1361 kg) 7950 lb (3606 kg) 2.3L GTDI 2WD 2 5000 lb (2268 kg)3 9950 lb (4513 kg) 3.5L TiVCT 2WD 2 2000 lb (907 kg) 7100 lb (3221 kg) 2.3L GTDI 4WD 1 2000 lb (907 kg) 7100 lb (3221 kg) 3.5L TiVCT 4WD 1 3000 lb (1361 kg) 8150 lb (3697 kg) 2.3L GTDI 4WD 2 5000 lb (2268 kg) 10150 lb (4604 kg) 3.5L TiVCT 4WD 2 5000 lb (2268 kg) 10400 lb (4717 kg) 3.5L GTDI 4WD 2 1 Without trailer towing package. 2 With trailer towing package. 3 For towing trailers up to 3500 pounds (1588 kilograms), use a weight-carrying hitch and ball, which uniformly spreads the trailer tongue loads through your vehicle ’s underbody structure. For towing trailers over 3500 pounds (1588 kilograms), up to the maximum trailer weight, we recommend you use a weight-distributing hitch to increase front axle load while towing. 240 Explorer (TUB) Canada/United States of America, enUSA, Edition date: 03/2016, First Printing Towing
ESSENTIAL TOWING CHECKS Follow these guidelines for safe towing: • Do not tow a trailer until you drive your vehicle at least 1,000 mi (1,600 km). • Consult your local motor vehicle laws for towing a trailer. • See the instructions included with towing accessories for the proper installation and adjustment specifications. • Service your vehicle more frequently if you tow a trailer. See your scheduled maintenance information. • If you use a rental trailer, follow the instructions the rental agency gives you. You can find information on load specification terms found on the tire label and Safety Compliance label as well as instructions on calculating your vehicle's load in the Load Carrying chapter. See Load Limit (page 232). Remember to account for the trailer tongue weight as part of your vehicle load when calculating the total vehicle weight. Hitches Do not use a hitch that either clamps onto the bumper or attaches to the axle. Distribute the trailer load so 10-15% of the total trailer weight is on the tongue. Weight-distributing Hitches WARNING Do not adjust a weight-distributing hitch to any position where the rear bumper of the vehicle is higher than it was before attaching the trailer. Doing so will defeat the function of the weight-distributing hitch, which may cause unpredictable handling, and could result in serious personal injury. When hooking-up a trailer using a weight-distributing hitch, always use the following procedure: 1. Park the loaded vehicle, without the trailer, on a level surface. 2. Measure the height to the top of your vehicle's front wheel opening on the fender. This is H1. 3. Attach the loaded trailer to your vehicle without the weight-distributing bars connected. 4. Measure the height to the top of your vehicle's front wheel opening on the fender a second time. This is H2. 5. Install and adjust the tension in the weight-distributing bars so that the height of your vehicle's front wheel opening on the fender is approximately half the way down from H2, toward H1. 6. Check that the trailer is level or slightly nose down toward your vehicle. If not, adjust the ball height accordingly and repeat Steps 2-6. When the trailer is level or slightly nose down toward the vehicle: • Lock the bar tension adjuster in place. • Check that the trailer tongue securely attaches and locks onto the hitch. • Install safety chains, lighting, and trailer brake controls as required by law or the trailer manufacturer. Safety Chains Note: Never attach safety chains to the bumper. Always connect the safety chains to the hook retainers of your vehicle hitch. To connect the trailer ’s safety chains, cross them under the trailer tongue and allow enough slack for turning tight corners. Do not allow the chains to drag on the ground. 241 Explorer (TUB) Canada/United States of America, enUSA, Edition date: 03/2016, First Printing Towing
Trailer Brakes WARNING Do not connect a trailer's hydraulic brake system directly to your vehicle's brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase. Electric brakes and manual, automatic or surge-type trailer brakes are safe if you install them properly and adjust them to the manufacturer's specifications. The trailer brakes must meet local and federal regulations. The rating for the tow vehicle's braking system operation is at the gross vehicle weight rating, not the gross combined weight rating. Separate functioning brake systems are required for safe control of towed vehicles and trailers weighing more than 1500 pounds (680 kilograms) when loaded. Trailer Lamps WARNING Never connect any trailer lamp wiring to the vehicle's tail lamp wiring; this may damage the electrical system resulting in fire. Contact your authorized dealer as soon as possible for assistance in proper trailer tow wiring installation. Additional electrical equipment may be required. Trailer lamps are required on most towed vehicles. Make sure all running lights, brake lights, turn signals and hazard lights are working. Before Towing a Trailer Practice turning, stopping and backing up to get the feel of your vehicle-trailer combination before starting on a trip. When turning, make wider turns so the trailer wheels clear curbs and other obstacles. When Towing a Trailer • Do not drive faster than 70 mph (113 km/h) during the first 500 mi (800 km). • Do not make full-throttle starts. • Check your hitch, electrical connections and trailer wheel lug nuts thoroughly after you have traveled 50 mi (80 km). • When stopped in congested or heavy traffic during hot weather, place the gearshift in position P to aid engine and transmission cooling and to help A/C performance. • Turn off the speed control with heavy loads or in hilly terrain. The speed control may turn off automatically when you are towing on long, steep grades. • Shift to a lower gear when driving down a long or steep hill. Do not apply the brakes continuously, as they may overheat and become less effective. • If your transmission is equipped with a Grade Assist or Tow/Haul feature, use this feature when towing. This provides engine braking and helps eliminate excessive transmission shifting for optimum fuel economy and transmission cooling. • Allow more distance for stopping with a trailer attached. Anticipate stops and brake gradually. • Avoid parking on a grade. However, if you must park on a grade: 1. Turn the steering wheel to point your vehicle tires away from traffic flow. 242 Explorer (TUB) Canada/United States of America, enUSA, Edition date: 03/2016, First Printing Towing
2. Set your vehicle parking brake. 3. Place the automatic transmission in position P. 4. Place wheel chocks in front and back of the trailer wheels. (Chocks not included with vehicle.) Launching or Retrieving a Boat or Personal Watercraft (PWC) Note: Disconnect the wiring to the trailer before backing the trailer into the water. Note: Reconnect the wiring to the trailer after removing the trailer from the water. When backing down a ramp during boat launching or retrieval: • Do not allow the static water level to rise above the bottom edge of the rear bumper. • Do not allow waves to break higher than 6 in (15 cm) above the bottom edge of the rear bumper. Exceeding these limits may allow water to enter vehicle components: • Causing internal damage to the components. • Affecting driveability, emissions, and reliability. Replace the rear axle lubricant anytime the rear axle has been submerged in water. Water may have contaminated the rear axle lubricant, which is not normally checked or changed unless a leak is suspected or other axle repair is required. TOWING THE VEHICLE ON FOUR WHEELS - 2.3L ECOBOOST™ Emergency Towing If your vehicle becomes inoperable (without access to wheel dollies, car-hauling trailer, or flatbed transport vehicle), it can be flat-towed (all wheels on the ground, regardless of the powertrain and transmission configuration) under the following conditions: • Your vehicle is facing forward for towing in a forward direction. • Place the transmission in position N. If you cannot move the transmission into N , you may need to override it. See Transmission (page 178). • Maximum speed is 35 mph (56 km/h). • Maximum distance is 50 mi (80 km). WARNING If your vehicle has a steering wheel lock make sure the ignition is in the accessory or on position when being towed. Recreational Towing Note: Put your climate control system in recirculated air mode to prevent exhaust fumes from entering the vehicle. See Climate Control (page 127). Follow these guidelines if you have a need for recreational (RV) towing. An example of recreational towing would be towing your vehicle behind a motorhome. We designed these guidelines to prevent damage to your transmission. 243 Explorer (TUB) Canada/United States of America, enUSA, Edition date: 03/2016, First Printing Towing
Front-wheel drive vehicles CANNOT be flat-towed (all wheels on the ground) as vehicle or transmission damage may occur. You must place the front wheels on a two-wheel tow dolly. If you are using a tow dolly, follow the instructions specified by the equipment provider. Four-wheel drive vehicles CANNOT be flat-towed (all wheels on the ground), as vehicle or transmission damage may occur. It is recommended to tow your vehicle with all four (4) wheels off the ground such as when using a car-hauling trailer. Otherwise, you cannot recreational tow your vehicle. TOWING THE VEHICLE ON FOUR WHEELS - 3.5L DURATEC/3.5L ECOBOOST™ Emergency Towing If your vehicle becomes inoperable (without access to wheel dollies or vehicle transport trailer), it can be flat-towed (all wheels on the ground, regardless of the powertrain and transmission configuration) under the following conditions: • Your vehicle is facing forward for towing in a forward direction. • Shift into neutral (N). If you cannot shift into neutral (N), you may need to override it. See Transmission (page 178). • Maximum speed is 35 mph (56 km/h). • Maximum distance is 50 mi (80 km). WARNING If your vehicle has a steering wheel lock make sure the ignition is in the accessory or on position when being towed. Recreational Towing Note: Put your climate control system in recirculated air mode to prevent exhaust fumes from entering the vehicle. See Climate Control (page 127). Follow these guidelines if you have a need for recreational (RV) towing. An example of recreational towing would be towing your vehicle behind a motorhome. We designed these guidelines to prevent damage to your transmission. You can tow your 3.5L EcoBoost or 3.5L Duratec equipped vehicle with all four wheels on the ground. If you tow your vehicle with all four wheels on the ground: • Tow only in the forward direction. • Release the parking brake. Vehicles with Keyless Start 1. Start the vehicle by pressing the brake pedal, and then pressing the keyless start button until the vehicle starts. 2. Press the brake pedal and shift the gearshift into neutral (N). 3. Turn the vehicle off by pressing the keyless start button once. 4. Disconnect the negative (black) cable from the battery. You need the door key to lock and unlock doors when the battery cable is disconnected. See Changing the 12V Battery (page 286). Note: The anti-theft system does not work until you reconnect the battery cable. Start the engine within 15 minutes of reconnecting the battery cable. Vehicles with an Ignition Key 1. Start the vehicle by pressing the brake pedal, and then turning the ignition key until the vehicle starts. 244 Explorer (TUB) Canada/United States of America, enUSA, Edition date: 03/2016, First Printing Towing
2. Press the brake pedal and shift the transmission into neutral (N). 3. Turn off your vehicle by turning the ignition key past the accessory position. The key position is between the accessory and off positions. See Ignition Switch (page 162). 4. Disconnect the negative (black) cable from the battery. See Changing the 12V Battery (page 286). Note: The anti-theft system does not work until you reconnect the battery cable. Start the engine within 15 minutes of reconnecting the battery cable. All Vehicles • Do not exceed 65 mph (105 km/h). • Start the engine and allow it to run for five minutes at the beginning of each day and every six hours thereafter. With the engine running and your foot on the brake, shift into drive (D) and then into reverse (R) before shifting back into neutral (N). Front-wheel Drive Vehicles Alternatively, you can tow your front-wheel drive vehicle with the front wheels off the ground by using a tow dolly, or with all four wheels off the ground using a vehicle transport trailer. If you are using a tow dolly, follow the instructions specified by the equipment provider. Four-wheel Drive Vehicles Alternatively, you can tow your Four-wheel Drive vehicle with all four wheels off the ground using a vehicle transport trailer. Do not tow your four-wheel Drive vehicle with the front wheels off the ground (by using a tow dolly) and the rear wheels on the ground. This causes damage to your four-wheel Drive system. If you are using a vehicle transport trailer, follow the instruction specified by the equipment provider. 245 Explorer (TUB) Canada/United States of America, enUSA, Edition date: 03/2016, First Printing Towing
BREAKING-IN You need to break in new tires for approximately 300 miles (480 kilometers). During this time, your vehicle may exhibit some unusual driving characteristics. Avoid driving too fast during the first 1000 miles (1600 kilometers). Vary your speed frequently and change up through the gears early. Do not labor the engine. Do not tow during the first 1000 miles (1600 kilometers). ECONOMICAL DRIVING Your fuel economy is affected by several things, such as how you drive, the conditions you drive under, and how you maintain your vehicle. You may improve your fuel economy by keeping these things in mind: • Accelerate and slow down in a smooth, moderate fashion. • Drive at steady speeds without stopping. • Anticipate stops; slowing down may eliminate the need to stop. • Combine errands and minimize stop-and-go driving. • Close the windows for high-speed driving. • Drive at reasonable speeds (traveling at 55 mph [88 km/h] uses 15% less fuel than traveling at 65 mph [105 km/h]). • Keep the tires properly inflated and use only the recommended size. • Use the recommended engine oil. • Perform all regularly scheduled maintenance. Avoid these actions; they reduce your fuel economy: • Sudden accelerations or hard accelerations. • Revving the engine before turning it off. • Idle for periods longer than one minute. • Warm up your vehicle on cold mornings. • Use the air conditioner or front defroster. • Use the speed control in hilly terrain. • Rest your foot on the brake pedal while driving. • Drive a heavily loaded vehicle or tow a trailer. • Carry unnecessary weight (approximately 1 mpg [0.4 km/L] is lost for every 400 lb [180 kilogram] of weight carried). • Driving with the wheels out of alignment. Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. • Adding certain accessories to your vehicle (for example bug deflectors, rollbars, light bars, running boards, ski racks or luggage racks) may reduce fuel economy. • To maximize the fuel economy, drive with the tonneau cover installed (if equipped). • Using fuel blended with alcohol may lower fuel economy. • Fuel economy may decrease with lower temperatures during the first 8– 10 miles (12 –16 kilometers) of driving. • Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain. 246 Explorer (TUB) Canada/United States of America, enUSA, Edition date: 03/2016, First Printing Driving Hints
• Transmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal. • Four-wheel-drive operation (if equipped) is less fuel efficient than two-wheel-drive operation. • Close the windows for high-speed driving. DRIVING THROUGH WATER WARNING Do not drive through flowing or deep water as you may lose control of your vehicle. Note: Driving through standing water can cause vehicle damage. Note: Engine damage can occur if water enters the air filter. Before driving through standing water, check the depth. Never drive through water that is higher than the bottom of the front rocker area of your vehicle. When driving through standing water, drive very slowly and do not stop your vehicle. Your brake performance and traction may be limited. After driving through water and as soon as it is safe to do so: • Lightly press the brake pedal to dry the brakes and to check that they work. • Check that the horn works. • Check that the exterior lights work. • Turn the steering wheel to check that the steering power assist works. FLOOR MATS WARNINGS Always use floor mats that are designed to fit the foot well of your vehicle. Only use floor mats that leave the pedal area unobstructed. Only use floor mats that are firmly secured to retention posts so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury. Always make sure that the floor mats are properly attached to the retention posts in the carpet that are supplied with your vehicle. Floor mats must be properly secured to both retention posts to make sure mats do not shift out of position. Never place floor mats or any other covering in the vehicle foot well that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle. Never place floor mats or any other covering on top of already installed floor mats. Floor mats should always rest on top of vehicle carpeting surface and not another floor mat or other covering. Additional floor mats or any other covering will reduce the pedal clearance and potentially interfere with pedal operation. 247 Explorer (TUB) Canada/United States of America, enUSA, Edition date: 03/2016, First Printing Driving HintsE176360