Faroudja Fdp Dila1080phd Installation And Operations Manual

31
1Pull out the plug from the power outlet
●Pull out the power plug from the outlet while the [STAND
BY] indicator is still on.
2Remove the lower filter
●Withdraw the filter backwards along the rail in the direc-
tion of the arrow.
3Remove the inner filter
●Push up and lift the claw at the base of the inner filter,
followed by drawing out the filter.
4Clean the filter
●Clean the filter with water and dry it, avoiding direct sun-
light. In extremely soiled cases, use of a neutral deter-
gent is...

32
Lamp replacementEXIT
Warning
Lamp replacementEXIT
EXIT
1000h
No Signal DVI-D
Cause (Details)
No device is connected to the DVI terminal.
The terminal is connected but there is no signal output.
[ Input the video signals.
When lamp time reaches 1000 hours
[ A message indicating “1000 h” will be displayed on the
screen.
●Press the [EXIT] button to clear the display.
At the moment when the accumulated lamp time reaches
1900 hours, a “Lamp replacement” message will be displayed.
In addition, when the...

33
About warning indicators
If abnormality occurs in this unit during projection, the warning mode w\
ill be triggered and the type of abnormality will be
indicated by a combination of indicators displayed on the control panel.\
 This unit will then automatically stop projection and  run
the cooling fan for about 90 seconds.
Warning
No.

Actions to be taken upon warning indications
Please follow the procedures below.
For Nos. 1-3
No. 1: Perform procedures to turn on/off the power again.
No.  2: After...

34
●This unit uses a microcomputer. External noise may cause it to malfuncti\
on. If this happens, turn off the power and remove
the plug from the power outlet. Insert plug again into the outlet and ch\
eck operation of the unit. (See Pages 20, 21 on how to
turn on/off the power of the unit.)
•Is the power cord disconnected?
• Is the lamp cover properly shut?
• Is the filter cover properly shut?
• Has the lamp life expired? (Has the lamp
usage time reached 2000 hours?)
• Is the lens cap removed?
• Is the...

35
9876
5432 1
8
16
24
7
15
23
6
14
22
3
11
19
2
10
18
5
13
21 4
12
20
1
9
17
Pin Arrangement
TMDS = Transition Minimized Differential Signaling
DDC = Display Data Channel
Terminal Description
Pin No. 1
2
3
4
5 Signal Name
N/C
RD
TD
N/C
GND Pin No.
6
7
8
9 Signal Name
N/C
N/C
N/C
N/C
Pin No.1
2
3
4
5
6
7
8
9
10
11
12 Signal Name
TMDS data 2-
TMDS data 2+
TMDS data 2/4 shield
N/C
N/C
DDC clock
DDC data
N/C
TMDS data 1-
TMDS data 1+
TMDS data 1/3 shield
N/C Pin No.
13
14
15
16
17
18
19
20
21
22
23
24...

36
[[
[[
Control of this unit via a computer is possible by connecting the comput\
er to this unit with a RS-232C cross cable (D-sub 9
pins). The commands to control this unit and the response data format a\
gainst the received commands are explained here.
For details, please consult your authorized dealer.
1. Communication SpecificationsCommunication specification for this unit are as follows:
2. Command Format
  2-1. Command data format
When sending a control command to this unit, use the following...

37
3Special parameters
Parameters for input video image format
Operation mode parameters
3. External control command table
Operation mode: Only Asking command is possible
Character0000
0001
0002
0004 Hex
30h 30h 30h 30h
30h 30h 30h 31h
30h 30h 30h 32h
30h 30h 30h 34h Meaning
Standby mode
Power-on mode
Cool down mode
Emergency mode
Operate HIDE
Left/Right Reversal
Top/Bottom Inversion Operation Mode U0F
U00
U17
U18 Z03 Power On



 ELSE



 Numeric Value




 ON/OFF





Asking
Data...

38
DILA1080pHD Home Theater Projector
D-ILA*
1(Reflective Active Matrix Principle)
D-ILA Device*2/0.82 (1920 pixels x 1080 pixels) x 3 (Total no. of pixels: Approx. \
6,220,000)
x 1.3 zoom lens (1.8:1 to 2.35:1) (Zoom/Focus adjustment: manual)
250 W Ultra-high Pressure Mercury Lamp
[Part No.: BHL5006-S / Rating: 250 W]
Approx. 40 to 200 (Aspect ratio: 16:9)
Approx. 1.5 m to 12 m
1080/60p signal, 1080/50p signal
1920 dots x 1080 dots
Horizontal:56.25 kHz, 67.43 kHz, 67.5 kHz
Vertical :50 Hz, 59.94 Hz, 60...

39
18120
67.5
38.2 298
300
29263.5
421
148
160
413

Dimensions (Unit: mm)
Top
Front Side
Bottom
M6 (Depth: 10 mm)
Mounting screw should be more than 6
mm but less than 10 mm in length. Center of Lens 

FAROUDJA WARRANTY STATEMENT
Faroudja®, a division of Genesis Microchip Inc. warranties that its products will
substantially conform to published specifications, subject to the terms and conditions
below. These warranties are limited to the first purchaser of the products (Purchaser) 
for the period listed below from the date of sale.
Video Processors: Two (2) years limited parts and labor
DVD Drives: One (1) year limited parts and labor
Plasmas (HD20 version):  Four (4) years limited parts and labor...