Faroudja Fdp Dila1080phd Installation And Operations Manual

11
Indicator Display on the Control Panel
LAMPTEMPST
AND B
Y
OPERATE
LAMP TEMPST
AND B
Y
OPERA TELAMP TEMPST
AND B
Y
OPERA TE
LAMP TEMPST
AND B
Y
OPERA TELAMP TEMPST
AND B
Y
OPERA TELAMP TEMPST
AND B
Y
OPERA TE
LAMP TEMPST
AND B
Y
OPERA TELAMP TEMPST
AND B
Y
OPERA TE
LAMP TEMPST
AND B
Y
OPERA TE
LAMP TEMPST
AND B
Y
OPERA TELAMP TEMPST
AND B
Y
OPERA TELAMP TEMPST
AND B
Y
OPERA TE
In addition to the standby mode, operate mode and cool down mode*, this \
unit also displays other operational states using...

12
1Remote Control’s Signal Transmitter
(☞  Page 17)
2[OPERATE ON] Button
When this unit is in the standby mode, pressing the
button for more than 1 second will turn this unit on and
cause the [OPERATE] indicator to light up. ( ☞ Page
20)
3[LIGHT] Button
Lights up illumination (light) of the remote control
buttons for about 10 seconds.
4[FOCUS] Button
Use this button to adjust focus of the projected image.
Press the button to switch to the image mode for focus
adjustment. Adjust focus using the focus...

13
Precautions for Using Batteries
Loading Batteries into the Remote Control
1Open the back cover
Press the back cover slightly and slide it in the direction of
the arrow.
2Load the batteries
Insert the 2 (AAA) batteries supplied according to the ,
  marks. To prevent short circuit, be sure to insert the  
(minus) end of the battery first.
3Close the back cover
Slide in the direction of the arrow to close the back cover.
Load batteries into the remote control. If the remote control starts to \...

14
Installing the Projector
Precautions for Installation
Please read the following carefully when installing this unit.
Minimum Space Required
Adjusting the Inclination
Vertical angle adjustment rangeAdjusting the vertical angle
While pushing the foot lever upward,
raise this unit to extend the front foot
(maximum extension is about 31
mm). To retract the foot, push the
level upward and lower the unit
slowly. This unit will be fixed at the
position where you released the foot
lever.
Fine-tuning the...

15
Projector and Screen Installation

When viewed from the left (or right) 
When viewed from the top (or bottom)
The optimum image can be obtained when the center of this unit lens and \
the screen are placed perpendicular to each other.
Take note of the projection angle when placing them. Failing to do so ma\
y give rise to trapezoidal distortion of the projected
image.
●This unit does not come with a function to correct trapezoidal distortio\
n.
Mounting  this Unit
When mounting of this unit is...

16
Projection Screen Size (DiagonalLength) of Aspect Ratio 16:9
40 (Approx. 101.6 cm)
50 (Approx. 127.0 cm)
60 (Approx. 152.4 cm)
70 (Approx. 177.8 cm)
80 (Approx. 203.2 cm)
90 (Approx. 228.6 cm)
100 (Approx. 254.0 cm)
110 (Approx. 279.4 cm)
120 (Approx. 304.8 cm)
130 (Approx. 330.2 cm)
140 (Approx. 355.6 cm)
150 (Approx. 381.0 cm)
160 (Approx. 406.4 cm)
170 (Approx. 431.8 cm)
180 (Approx. 457.2 cm)
190 (Approx. 482.6 cm)
200 (Approx. 508.0 cm) Approximate Projecting Distance
W (Wide) -T (Tele)
(Approx....

17
Effective Range of Remote Control Unit
The operable distance of the remote control unit is about 7 m for direct\
 reception. The remote control unit can be used by having
the transmission signal reflected off a screen.
● If the fluorescent lamp is lit, the remote control unit might not functi\
on properly.
Screen
Remote Control Unit Remote Sensor (Rear)
This unit

 When reflecting off a screen
Ensure that total of distance A between this unit and screen  and distan\
ce B between remote control and...

18
Connecting to Various Devices
Connecting to Devices
Before connection, be sure to turn off both the projector and the device\
 to be connected.

Connecting to digital video processors
●Read the manual that is supplied with the digital video processor thorou\
ghly.
● The signal may attenuate and the image may become unstable depending on \
the DVI cable. Use the high quality DVI
cable below 5 m. When using DVI cable above 5 m, use a split system or o\
ptical fiber cable.
Right Side of this unit
DVI...

19
2
1
1Connect the supplied power cord to the power in-
put terminal of this unit
2Insert the main plug of the supplied power cord
into the wall outlet
Connecting the Power Cord (supplied)
After all devices have been connected, connect the supplied power cord.
Power Cord (supplied)
●
Since the power requirement of this unit is high, insert the power plug \
directly into a wall outlet.
● When not using devices, remove the power plug from the wall outlet.
● Do not use power cords for connection other than...

20
LAMPTEMPST
AND BYOPERA TEON
ENTER
OFF
FOCUSTEST
MENUEXIT
PRESETHIDE
LIGHT
OPERATE1-2
LAMP TEMPST
AND BYOPERATE
2
3
If setting for this unit is not completed, please refer to “Adjustmen\
ts and Settings Using Menus”( ☞ Page 22) upon turning on the
power and perform the required setting accordingly. Once the basic setti\
ng is completed, this unit can be used by simply
performing the following operation procedures.
Basic Operation Procedures
Light on
‘Tele’
‘Wide’
‘Near’ ‘Far’
Notes
● Upon projection,...