Faroudja Fdp Dila1080phd Installation And Operations Manual

Home Theater Optimized
DILA1080pHD
Installation and 
Operations Manual
NOTICE: THIS PROJECTOR HAS BEEN SIGNIFICANTLY MODIFIED AND OPTIMIZED TO PRODUCE VERY HIGH
QUALITY IMAGES USING THE FAROUDJA PROCESSOR.
ANY CHANGES MADE TO THESE SETTINGS CAN CORRUPT THIS PROCESS. RESETTING THE OPTIMIZATION IS NOT COVERED UNDER WARRANTY.
™ 

2
About burning-in of the D-ILA device
Do not allow the same still picture to be projected for a long
time or an abnormally bright video picture to be projected.
Do not project video images with high-intensity or high con-
trast
on a screen.  The video image could be burnt into the D-ILA
device.
Use special care when projecting video games or computer
program images.  There is no problem with ordinary video-cas-
sette playback images.
About the installation place
Do not install the projector in a place...

3
–Slots and openings in the cabinet are provided for ventila-
tion.  These ensure reliable operation of the product and pro-
tect it from overheating.  These openings must not be blocked
or covered. (The openings should never be blocked by plac-
ing the product on bed, sofa, rug, or similar surface. It should
not be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided and the
manufacturer ’s  instructions have been adhered to.)
For proper ventilation,...

4
WARNING:
THIS  APPARA TUS MUST  BE EARTHED. IMPOR TANT :
The wires in the mains lead on this product are colored in
accordance with the following cord:
Green-and-yellow :Earth
Blue :Neutral
Brown :Live
As these colors may not correspond with the colored mak-
ing identifying the terminals in your plug, proceed as fol-
lows:
The wire which is colored green-and-yellow must be con-
nected to the terminal which is marked 
  with the letter E
or the safety earth or colored green or green-and-yellow .
The...

5
Maintenance Procedures
●Clean dirt on the cabinet
with a soft cloth. In case of heavy soiling, soak a cloth in
neutral detergent diluted with water, wring dry and wipe,
followed by wiping again using a dry cloth.
●Pay attention to the following as the cabinet
may deteriorate in condition, get damaged or
paint may come off.
•Do not wipe with a stiff cloth
• Do not wipe with force
• Do not wipe with thinner or benzene
• Do not spray volatile chemicals like insecticide
• Do not allow prolonged contact...

6
The following accessories are packed together with this unit. Please con\
firm all items.
If any item is missing, please contact your dealer.
Contents
Instructions........................................................................\
........................................... ....................x 1
Guarantee ........................................................................\
.............................................. ...................x 1
Power Cord...

7
6Remote Sensor (Front)
When operating with the remote control,
aim it towards this sensor. (☞ Page 17)
•A  remote sensor is also located on the rear of
the unit.
7Focus Ring
Turn manually to focus the projected image.
( ☞  Page 20) Remove metal cover to access lens.
8Zoom Ring
Turn manually to zoom the projected image.
( ☞  Page 20) Remove metal cover to access lens.
Controls and Features
1Backup Control Panel
Use in case IR remote cannot be used.
Panel is located behind metal plate.
2AC Power Input...

8
1Connection Panel
Access panel by removing four screws and removing
side panel.
2Lamp Cover
Remove this cover when replacing the lamp.
See manual insert for details on accessing bulb.
3Exhaust Vent
Warm air is expelled through this vent to keep the
system cool. Do not block the exhaust vents.
Metal around vent is hot -  DO NOT TOUCH while unit
is in operation
4Remote Sensor (Rear)
When operating with the remote control, aim it towards
this sensor. (☞ Page 17)
● A remote sensor is also located at the...

9
1[SYNC OUT] Terminal
This terminal is intended for servicing purposes. Do not
use it.
Using it may give rise to error or malfunction of the unit.
2[SERVICE] Terminal
This terminal is intended for servicing purposes. Do not
use it.
Using it may give rise to error and malfunction of the
unit.
Connector Panel
DVI
VIDEO INCONTR OLRS-232CSERVICE
SYNC
OUT
24
13
3[RS-232C] Terminal (D-sub 9 Pin)
This is the RS-232C interface-specific terminal. This
unit can be controlled by a computer connected
externally. (...

10
7[OPERATE] Indicator
Light on:W hen this unit is in operation (during projec-
tion). ( ☞ Page 20)
8[OPERATE] Button
When this unit is in the standby mode, pressing this
button for more than 1 second will turn this unit on and
cause the [OPERATE] indicator to light up.
Press it for 1 second or more again to switch the unit to
the cool down mode, which will automatically switch to
the standby mode after about 90 seconds. ( ☞ Page 20)
●The [OPERATE] button will not work within approxi-
mately 1 minute...