Epson Stylus Pro 4800 User Manual

11
Introduction|11
Before you call, make sure you have your Unit ID number, which is 
included with the Epson Preferred Protection Plan information that came 
with your printer. You’ll also need your printer serial number and proof of 
purchase. 
Epson also provides technical assistance 24 hours a day through the World 
Wide Web. You can reach Epson Support at http://support.epson.com. At 
this site, you can download drivers, firmware, and other files, look at product 
documentation, access...

12
12|Introduction
Windows System Requirements
To use your printer in either a stand-alone or peer-to-peer network 
environment, your system should include the requirements listed below:
IBM®-compatible PC with a Pentium® IV 1.7 GHz or higher processor 
recommended 
Windows® 2000 or XP
For 10/100 Base TX Ethernet connection: Ethernet equipped PC 
At least 1GB of RAM 
At least 100MB of free hard disk space to install the software, and at 
least 2GB of free hard disk space for processing files (8GB or more...

13
Introduction|13
Important Safety Instructions
Before using your printer, read the following safety instructions to make sure 
you use the equipment safely and effectively.
The printer weighs about 88 lb (without ink or paper), and should be 
lifted by two people.
When setting up the printer, make sure you have enough space around 
it, as shown below. You may need more space behind the printer if you 
print on large sheets of heavy stock or posterboard.
Place the printer on a flat, stable surface that...

14
14|Introduction

This product’s power cord is designed for use with this product only. 
Using it with other equipment may result in fire or electric shock.
Do not use a damaged or frayed power cord.
If you use an extension cord with this product, make sure the total 
ampere rating of devices plugged into the extension cord does not exceed 
the cord’s ampere rating. Also, make sure the total ampere rating of all 
devices plugged into the wall outlet does not exceed the wall outlet’s 
ampere rating.
Do...

15
Introduction|15
Ink Cartridge Safety Instructions
Keep ink cartridges out of the reach of children and do not drink the 
ink.
Store ink cartridges in a cool, dark place.
If ink gets on your skin, wash it off with soap and water. If ink gets in 
your eyes, flush them immediately with water.
Shake an ink cartridge well before installing it for best results. 
Do not use an ink cartridge beyond the date printed on the cartridge 
carton.
Use up the ink cartridge within six months of installation for best...

16
16|Introduction
sp4800Guide.book  Page 16  Tuesday, March 7, 2006  3:49 PM
 

17
17
This chapter includes the following information:
Unpacking
Setting up and plugging in
Installing ink
Connecting to your system
Connecting to the network
Installing the software 
Updating your printer firmware 
Unpacking
1. Make sure you have all these parts for your Epson Stylus Pro 4800:
Chapter 1: 
Setting Up 
the Printer
WARNING: The printer 
weighs about 88 pounds, 
and should be lifted by two 
people.
Note: The printer also 
includes a black ink 
conversion kit (3 
cartridges). Save the kit in...

1-18
18|Setting Up the Printer
2. Remove all the packing materials and tape. Save the box and packaging 
in case you need to ship the printer.
3. Remove the two screws and remove the carriage retainer bracket. Store 
the screws and retainer bracket in case you need to transport the printer 
later. 
4. Unlock the print head carriage by pulling the green tab to the left. Do 
not push down and do not remove the tab. 
Note: To prevent paper 
jams, don’t place the 
screws back in the 
printer....

1-19
Setting Up the Printer|19
Setting Up and Plugging In
1. Connect the power cord to the AC inlet on the back of the printer. 
2. Plug the other end of the power cord into a properly grounded electrical 
outlet.
3. Insert the paper tray into the slots at the front of the printer.
Installing Ink
Use the ink cartridges that came with your printer for initial ink charging. 
During the initial installation process, it is normal for up to one-third of the 
ink in each cartridge to be used. 
1. Press the...

1-20
20|Setting Up the Printer
2. Press both ink compartment covers to open them.
3. Raise both ink levers.
4. Remove each ink cartridge from its package and gently shake the 
cartridge.
sp4800Guide.book  Page 20  Tuesday, March 7, 2006  3:49 PM