Epson Projector Moviemate 25 User Manual

11
Quick Start
1Place MovieMate in a position to project 
the best size image onto the screen.
The further you place MovieMate away from the 
screen, the larger the projected image becomes. 
You can project on a wall if you want an image 
larger than the size of the screen.
For detailed projection distance values, see
page 60.
You can adjust the position of the projected 
image vertically and horizontally by using the 
lens shift dial, as described on page 13.
2Position MovieMate so that it is parallel...

12
1Press   to open the disc tray.
A beep sounds and the power comes on.
You can also press   on the remote control. 
2Place the disc in the disc tray with the label 
facing up.
3Press   to close the disc tray.
For all discs except  , the projection lamp 
comes on automatically, and projection begins. It 
takes a few seconds for the lamp to warm up and 
project at full brightness.
To play  , press   to start audio play-
back. The projection lamp does not turn on. 
You can also press    on the remote...

13
Adjust the image and sound as follows:
Adjusting the picture and sound
Adjusting the size of the 
projected image (Zoom ring)Setting the focus
(Focus ring)
Adjusting the image 
position (lens shift)
You can move the position of the pro-
jected image up, down, left and right, 
using the lens shift. The range of 
movement is shown in the diagram.
Adjusting the volume 
To increase the size, 
turn towards [W]. To decrease the size, turn 
towards [T]. 
* The clearest image is obtained when both 
the...

14
Press .
 To resume playback, 
press .
1Remove the disc from the disc tray.
2Press .
If the lamp was on, the lamp turns off and the 
Image Off light flashes orange (during cool-
down).
“Now Cooling” appears in the display window 
above the DVD tray. 
The confirmation buzzer beeps twice to indicate 
that cool-down has completed.
3Turn off the main power switch.
If you only press   to turn off the power, 
MovieMate continues using electricity.
4Replace the lens cover.
Keep the lens cover in place when...

15
Quick Start
From here on, operations are explained primarily using the buttons on the remote control. If the same button is available 
on the MovieMate control panel, you can also use it.
Press   during playback.
•On the control panel, press  .
•To resume playback, press  .
•Press  to toggle between play/pause.
Press   or   during playback.
•There are 5 levels of reverse/forward search 
speed that change each time the buttons are 
pressed.
•Press   to return to normal playback.
•On the control panel,...

16
Press   during playback.
MovieMate replays the previous 10 seconds.
Press   or   during playback.
Press   once to return to the start of the chapter 
or track being played. After this, playback returns 
to the start of the previous chapter/track each time 
you press   (Except for  ).
Press   during paused playback.
•A single frame is advanced each time you press 
. 
•Press   to return to normal playback.
Make sure the switch is set to the [Function] position
•Depending on the type of disc, this...

17
Quick Start
1Press   at the point where you want 
to begin slow motion playback. The image  
pauses.
2Press .
•There are 5 levels of playback speed that change 
each time you press  .
• For slow motion review, press  . 
There are 5 levels of review speed that change 
each time you press    .
•Press   to return to normal playback.
•Sound is not output during slow-motion play-
back.
The break function is useful if you want to get up or 
move around during a movie. By simply pressing the 
 button you can...

18
Advanced 
Operations
Press .
When you press   the brightness of the display window and the indi-
cators on the main unit change as shown below. DIMMER AUTO is the 
default setting.
Controlling Playback
•When an   is inserted, this function is not available, even when 
“DIMMER AUTO” is set. It changes to “DIMMER OFF.”
•In standby mode, the brightness cannot be changed, even if   is 
pressed.
•Once the brightness is changed, it is saved even after the main power 
switch is turned off.
Changing the...

19
Advanced Operations
Some   have one or both of the following types of menus.
Top menu: When multiple titles (video and audio) have been recorded, the 
top menu lets you select them. 
Menu: You can use menus to select chapters and playback settings such as 
angle, audio, and subtitles. 
1Press   or   during playback or when stopped.
2Press   to select the item you want to see.
You can also select the title number or chapter number directly using the 
numeric buttons. 
3Press .
Using the numeric...

20
When you insert a Video CD with PBC (playback control) enabled, a menu 
screen is displayed. You can select the scene or information you wish to see  
from this menu.
1Insert a Video CD that includes PBC. 
The following type of menu is displayed.
2Select the item you want to see using the numeric buttons.
For instructions on using the numeric buttons, see page 19.
The selected contents are played.
To turn to the previous/next page of the menu screen:
Press  /  when the menu screen is displayed.
To...