Epson Projector Emp Ts10 User Manual

9
Basic Operations
Turning Off the Projector
Follow the procedure below to turn off the power of the projector.
Procedure
1Turn off the power for the signal 
sources that are connected to the 
projector.
Check that the power for all connected 
components has been tuned off.
2Press the [Power] button on either the 
remote control or the projectors 
control panel.
The confirmation message shown left will appear.
If you do not wish to turn off the power, press any 
other button.
If you do not press any...

Turning Off the Projector
10
6
Set the R/C switch on the remote control 
to the OFF position.
7Retract the front adjustable foot if it is 
extended.
Gently push down on the projector while pressing 
the foot adjust button.
8
Attach the lens cover.
Attach the lens cover to the lens when not using 
the projector, in order to stop the lens from 
getting dusty or dirty.
If you leave the R/C switch at the ON 
position, the remote control will continue to 
consume battery power.
Move the R/C switch to the OFF...

11
Basic Operations
Adjusting the Screen Image
You can adjust the screen image in order to obtain the best possible picture.
The size of the projected image is basically determined by the distance from the projector to the screen. 
(Setup Guide)
The following procedures explain how to adjust the screen image once the projector itself has been set up.
ProcedureTurn the zoom ring on the projector to 
adjust the image.
The image can be enlarged in this way to 1.35 
times the normal size.
If you would like...

Adjusting the Screen Image
12
When the projector is set up at an angle, keystone distortion may appear in the projected images. If the 
projector is adjusted to within a range of approximately 30° vertically or 10° horizontally, the keystone 
correction function can be used to adjust this keystone distortion. 
The values given here are for when the image is at the smallest zoom setting (telephoto). The maximum 
angles  will be smaller if the zoom setting has been increased in the wide angle direction....

13
Basic Operations
Procedure
 
Procedure to follow if using both horizontal and vertical keystone correction:
1. With the front adjustable foot retracted, set the projector so that it is fully horizontal.
2. Extend the front adjustable foot to adjust the angle as necessary.
3. Adjust the vertical keystone distortion until both sides of the picture are vertical.
4. Adjust the horizontal keystone distortion until the top and bottom edges of the picture are both horizontal.
•
•• •When keystone correction...

14
Adjusting the Image Quality
The quality of the screen images can be adjusted as follows.
Turn the focus ring to adjust the image 
focus.
The following five color modes have been preset for use with images with varying characteristics. You can 
use these color modes to obtain the optimum image quality easily, just by selecting whichever color mode 
best suits the images. The brightness of the projected images will vary depending on the mode.
ProcedurePress buttons [1] to [5] on the remote 
control to...

15
Basic Operations
This function changes the aspect ratio of video images from 4:3 to 16:9 when video images are being 
projected. Images which have been recorded in digital video or onto DVDs can be viewed in 16:9 wide-
screen format. 
ProcedureThe aspect ratio changes each time the 
[Resize] button on either the remote 
control or the projectors control panel is 
pressed.
Selecting the Image Aspect Ratio
For SDTV
For HDTV
Changing the display position for 16:9 display
Volume A/V Mute
Resize
Projector...

Adjusting the Image Quality
16
Computer images can be adjusted automatically to the optimum images.
Automatic adjustment involves adjustment of the following three items: 
Tracking
, Display position and Sync (synchronization).
ProcedureWhile an image is being projected from 
the computer, press the [Auto] button on 
either the remote control or the 
projectors control panel.
The screen will appear black while the 
adjustment is being made.
IIf vertical stripes appear in the projected images, and this...

17
Basic Operations
IIf flickering, fuzziness or interference appear in images that are input from 
the computer, and this cannot be fixed using automatic adjustment, you will 
need to adjust the sync(synchronization)
 manually using the following 
projection.
ProcedureWhile holding down the [Shift] button on 
the projectors control panel, press the 
[Sync +] button.
The sync value increases each time the button is 
pressed.
While holding down the [Shift] button on 
the projectors control panel, press...

18
Adjusting the Volume
Yo can adjust the volume of the sound coming from the projectors built-in speaker.
ProcedurePress the [Volume   ,   ] button on the 
projectors control panel or the 
[Volume -,+] button on the remote control.
If you press the [   ] or [+] side, the volume 
increases, and if you press the [  ] side or [-] 
side, the volume decreases. While the volume is 
being changed, the volume value appears in the 
volume gauge.
Volume A/V Mute
Sync-KeystoneShift
Resize
Remote control Projector