Epson Projector Emp 8300 User Manual

130
Saving a Users Logo Saving a Users Logo
The image to be recorded and a selection marquee 
box will be displayed, so move the marquee box to 
select the part of the image to use.
Tilt the [ ] button on the remote control or press the [Sync +], 
[Sync -], [Tracking +] and [Tracking -] buttons on the 
projectors control panel to select the part of the image to use as 
the users logo, and then press the [Enter] button on the remote 
control or the [Auto/Enter] button on the projectors control 
panel....

131
Saving a Users Logo Saving a Users Logo
Select Yes at the confirmation screen, and then 
press the [Enter] button on the remote control or the 
[Auto/Enter] button on the projectors control panel.
The image will then be saved. Once the image has been saved, 
the message Completed. will be displayed.
7
Save image as users logo?If you save it, the previous users logo willbe overwritten.
YESNO Users Logo
TIP
 Saving the users logo may take a few moments (about 15 seconds). 
Do not use the projector or...

132
Optional AccessoriesThe following optional accessories are available for purchase if required. This list of optional accessories is current as of March 2003. Details of accessories are 
subject to change without notice.
Hard travel case ELPKS50
Use this case if you need to carry the projector by hand.
Spare lamp ELPLP23
(Set with spare lamp and two spare air filters)
Use as a replacement for spent lamps.
Filter kit (3 sets of 2 air filters (total 6)) ELPAF02
Use as a replacement for spent air...

133
Optional Accessories Optional Accessories
*1 cannot be installed by the customer. Please contact your dealer for 
assistance.*2 A special method of installation is required in order to suspend the 
projector from the ceiling. Please contact your supplier if you would 
like to use this installation method.
Standard lens
*1
 ELPLS02
(Projection distance ratio: Approx. 1.8–2.4)
Rear projection wide lens
*1
 ELPLR02
(Projection distance ratio: Approx. 0.86)
Long throw zoom lens
*1
 ELPLL04
(Projection...

134
GlossaryThe following table contains explanations of some of the terms used in this guide which may be unfamiliar or which are not explained in the text of the guide. 
Further information can be obtained by referring to other commercially-available publications.
3-2 pull-down functionThis function directly converts image sources that have been recorded in the same 24-frame format used for movies into 60-
frame progressive signals. This allows data such as DVD software that has been recorded in...

135
Glossary Glossary
EMP Link21LA utility software program that allows the projector to be connected to a computer so that the computer can be used to control 
the projector. For details on acquiring the software and for instructions on using the software and compatible projector 
models, please visit the web site http://www.epson.co.uk/support/download/projector.htm.
Film judgment function
A function for judging whether an image source is a 24 Hz progressive film source or not.
GatewayA server (router)...

136
Glossary Glossary
Subnet mask
A series of numbers that define the number of bits to be used for network addresses in a network (subnet) that is divided up 
according to IP addresses.
SVGAA type of video signal with a resolution of 800 (horizontal) × 600 (vertical) dots which is used by IBM PC/AT-compatible 
computers.
S-Video
A video signal which has the luminance component and colour component separated in order to provide better image quality.
It refers to images which consist of two independent...

137
List of ESC/VP21 CommandsCommand List
When a power ON command is sent to the projector, the power for the 
projector turns on. When the projector is in a command ready state, it 
returns the 3Ah (:) code.
Furthermore, when command processing is complete, the projector also 
returns a : code.
The : code status can be used to determine whether the projector is ready 
or busy. If command processing terminates with an error, an error message 
is output and then the : code is sent.
Communication Protocol...

138
List of ESC/VP21 Commands List of ESC/VP21 CommandsCable Layouts
Serial connection•
•• •Connector shape : D-Sub 9-pin (male)•
•• •Projector input 
connector: Control (RS-232C)

 (PC serial cable) 
Signal Function
GND
5
5
GND
GND Signal wire earth
RD
2
3
TD
TD Transmit data
TD
3
2
RD
RD Receive data
DTR
4
6
DSR
DSR Data set ready
DSR
6
4
DTR
DTR Data terminal ready

USB connection•
•• •Connector shape : USB(type B)
(type B) 

139
List of ESC/VP21 Commands List of ESC/VP21 CommandsUSB Connection Setup
In order to control the projector using ESC/VP21 commands via a USB 
connection, the following preparations must be carried out.PROCEDURE
Download the EMP Link21L
 utility software from the 
EPSON website to the computer being used.
For details on acquiring the software, please visit the Web site 
http://www.epson.co.uk/support/download/projector.htm
.
The USB driver (USB-COM Driver) will be downloaded 
together with the utility...