Epson Projector Emp 54 User Manual

30
Preventing theft (Password Protect)
Once the setting is complete, press the [Menu] 
button.
10
TIP
 When the time period has elapsed and the password is entered, projection will start again, the Time-elapsed setting will be reset to 
0 and the countdown will start again.
 Make a note of the password so that you do not forget it and keep it  in a safe place.
 If you lose the remote control, you will not be able to enter the  password. Keep the remote control in a safe place at all times. 

Basic OperationsThis chapter describes basic operations such as turning the projector on and off and adjusting the projected images.Turning On the Projector.................................... 32
 Connecting the Power Cable .............................................. 32
 Turning On the Power and Projecting Images .................33
Turning Off the Projector ................................... 35
Adjusting the Screen Image .............................. 37
 Adjusting the Image Size (Zoom Function)...

32
Turning On the ProjectorTurn on the power to start projecting images.Connecting the Power Cable
PROCEDURE
Check that the power is turned off for the projector 
and all components connected to the projector.Connect the computer or other video source to the 
projector.  p.16, p.22Remove the lens cover.
Hook your finger under the top of the lens cover and pull to 
remove it.
Connect the accessory power cable to the projector.
Check that the power cable connector is facing the same way as 
the power inlet...

33
Turning On the ProjectorTurning On the Power and Projecting Images
PROCEDURE
Check that the Power indicator has stopped flashing 
and is lit orange.Turn on the power for all equipment connected to the 
projector.
For a video source, press the [Play] button at the video source to 
start playback if necessary.
Press the [Power] button on either the projectors 
control panel or the remote control to turn on the 
power for the projector.
A beep will sound to indicate that the projector is starting up.
The...

34
Turning On the Projector
If more than one external device is connected to the 
projector, use the remote control or projector control 
panel buttons to select the image source to be 
projected while referring to the following table.
* The items selected using the Input Signal command in the Image 
menu will appear.
Port
Button to press
Display at top-right 
of screen
Remote control
Projector
Computer1/
Component 
Video1
[Computer1/2]
The image 
source changes 
each time 
[Source] is 
pressed.
If no...

35
Turning Off the ProjectorFollow the procedure below to turn off the power of the projector.
PROCEDURE
Turn off the power for the signal sources that are 
connected to the projector.
Check that the power for all connected components has been 
turned off.Press the [Power] button.
The following confirmation message will appear.
If you do not want to turn off the power, press any button except 
the [Power], [Page down] or [Page up] button.
If you do not press any button, the message will disappear...

36
Turning Off the Projector
If not using the projector for a long period, unplug the 
power cable from the electrical outlet.Attach the lens cover.
Attach the lens cover to the lens when not using the projector, 
in order to stop the lens from getting dusty or dirty.
4
CAUTION
Do not disconnect the power cable from the outlet while the Power 
indicator is still flashing orange, otherwise it may result in errors in 
projector operation and reduce the lamp unit operating life.5
Lens cover 

37
Adjusting the Screen ImageThese functions correct and adjust the projected images so that the optimum 
images can be obtained.Adjusting the Image Size (Zoom Function)
The size of the projected image is  basically determined by the distance 
from the projector to the screen.    p.15
The following procedures explain how to  adjust the screen image once the 
projector itself has been set up.PROCEDUREAdjust by turning the zoom ring.
The image can be enlarged in this way to 1.2 times the normal size.
If...

38
Adjusting the Screen ImageAdjusting the Image Angle and Automatic Keystone Correction Function
The projector should be set up so that it is as perpendicular to the screen as 
possible.
If it is not possible to set up the projector so that it is perpendicular to the 
screen, it can be set up at a slight vertical angle instead. You can extend or 
retract the front adjustable feet to adjust the upward projection angle 
within a maximum range of 10°.
PROCEDUREWhile pressing the two foot adjust buttons at...

39
Adjusting the Screen ImageWhen the projector is tilted vertically, it will cause keystone distortion to 
appear in the image. However, the projector is equipped with an automatic 
keystone correction function that can  automatically correct this keystone 
distortion as long as the vertical  angle of tilt is within a range of 
approximately 15º *. Automatic keystone correction is carried out 
approximately one second after the projectors power is turned on and the 
projector has been positioned. * This...