Epson Projector Emp 5100 User Manual

							43Changing Menu Settings
8. [Presently Selected] will appear right next to the function you
want to customize instead of [Select]. (If the function has been
selected already, [Presently Selected] appears.)
9. You are now finished.
*If you want to change the function you customized, perform the
above steps 1 to 8 again.
Using the functions:
* The [Volume], [Mute] and [Freeze] buttons are always available,
even when you have customized the above functions. However, if you
press any other button, its function has priority over the other
buttons and the customized function is cancelled.
* If ÒNo SignalÓ appears on the screen or no suppor ted signal is
being entered, no function will work.
Zoom
1. Press the [Custom] button on the remote control. (Switches to
zoom display mode.)
2. Enlarges the displayed image +1.25 times each time the [Left
Click] button on the remote control is pressed. (An image can be
enlarged up to four times.)
3.
Reduces it +0.75 times each time the [Right Click] button on the
remote control is pressed. (An image can be reduced up to one time.)
4. If an enlarged image falls partly outside of the display area, it can
be moved horizontally or vertically to adjust its position by using
the [Pointer] on the remote control.
5. The Zoom function is cancelled by pressing the [Custom] button
on the remote control. (The image returns to previous size.)
Preview
1. Press the [Custom] button on the remote control.
2. The screen turns to black. (This lasts approx. 4 seconds.) 
						

							443 ¥ Using the Menus
3. The screen is divided into four quadrants, each of which shows
the projection images currently being entered by each of the
input sources.
4. The projection image is switched each time the [Right Click]
button on the remote control is pressed. (Each input source
name flashes on the screen.)
5. The Preview function is closed by pressing the [Left Click]
button on the remote control. Next the image you selected in
step 4 will be displayed on the screen.
6. The Preview function is cancelled by pressing the [Custom]
button on the remote control. (The screen will revert to the
image shown before the Preview function was used.)
Strobe
1. Press the [Custom] button on the remote control.
2. The subdivided image you selected is projected on the screen at
the top left. 
						

							45
3. Press the [Left click] button on the remote control once.
4. The Strobe display is started. (If you set the number of frames to
9, they are displayed in the order of 1 to 9.)
5. By pressing the [Left click] button on the remote control again,
you can go back to the step 2.
6. The Strobe function is cancelled by pressing the [Custom] button
on the remote control. (The screen will revert to the image
shown before the Preview function was used.)
To change the number of frames and the time interval:
1. Press the [Right click] button on the remote control once.
2. The Strobe setting menu appears.
3. Set the number of frames and time interval by using the Pointer
button on the remote control.
4. Press the [Right click] button on the remote control again.
5. The Strobe setting menu is closed.
Changing Menu Settings 
						

							463 ¥ Using the Menus
Counts of frames, Time
Pressing the remote controlÕs Click 1 button while strobe display is
being performed displays a screen for specification of the counts
frames and the time interval. You can set the frame count to 4, 9 or
16, and the time interval from 0.1 to 1 second in 0.1 second incre-
ments.
Press the remote controlÕs Click 2 button again to clear the setting
screen.
RESET ALL
Executing this command resets the settings in all menus to their
factor y defaults.
Select this item and then press a Click button or the  button
to display the confirmation screen.
Next, select Yes and then press a Click button or the  button
to reset all menu items.
If you change your mind, select No and then press a Click button or
the  button to clear the confirmation screen without chang-
ing any settings. 
						

							47
4
Using ELP Link II 
						

							484  ¥  Using ELP Link II
Introduction
To use the ELP Link II software, you need one of the following
operational environments.
       Windows Ver. 3.1 (English)
       Windows 95 (English)
       MacOS System (from ver. 7)
This instruction manual tells you how to use ELP Link II.
The application ELP Link II supports two functions related to the
projector.
One is the projector control function which enables you to control
the projector (screen display, sound, etc.) from a computer and to
manipulate the settings (user logo setting, etc.) which the projector
cannot control.
The other function is the presentation support function which
enables you to control the presentation application (PowerPoint, etc.)
through a remote control and to perform the real-time presentation
effectively (adding lines, underlining or a stamp, etc. on the slide
screen during your presentation). 
						

							49
How to connect
¥For IBM PCs and IBM compatible PCs (Windows)
Please refer to the section ÒConnecting to a computerÓ in this
manual (pages 7~14).
¥For Macintosh
Please refer to the section ÒConnecting to a computerÓ in this
manual (pages 7~14).
How to connect 
						

							504  ¥  Using ELP Link II
How to install
For IBM PCs and IBM compatible PCs (Windows)
Start Windows.
Insert the floppy disk with the ELP Link II software into floppy disk
drive [A]. (It is assumed your floppy disk drive is drive A.)
The ELP Link II software to be installed depends on the computer
you are installing it on.
Select the Run command from the File menu in the Program
Manager. The Run dialog box appears on the screen.
Type [A: SETUP.EXE] in the [Command Line] box and click the
[OK] button.
The drive letter [A] must designate the proper drive (the floppy disk
drive into which you inserted the disk with the ELP Link II soft-
ware).
The ELP Link II set-up window will be displayed after a while.
Follow the instructions on the scr een to complete the installation.
When the termination screen appears, click the [OK] button to finish
the installation.
¥If you use the software often, place it in the Startup program
group. This is ver y convenient.
¥Please refer to your Windows Instruction Manual. 
						

							51
For Macintosh
Insert the floppy disk with the ELP Link II software into the floppy
disk drive. The ELP Link II folder appears on the screen. Double-
click the folder, then an ELP Link II icon will appear.
Copy the icon to a local hard disk with a drag-and-drop action.
To be able to use ELP Link II, restart the system.
¥When you install the ELP Link II software, make a new folder and
designate the disk drive to be used.
¥Please refer to your Macintosh Instruction Manual.
How to install 
						

							524  ¥  Using ELP Link II
Starting and exiting ELP Link II
¥To start ELP Link II
Double-click the ELP Link II icon to start the application. First an
opening screen appears, then the main ELP Link II window will
appear with a reduced size.
¥For Windows 3.1
Double-click the minimized ELP Link II window.
¥For Windows 95
Click the ELP Link II button on the taskbar.
¥For Macintosh
Open the local hard disk that you copied the ELP Link II.
When double-click the ELP Link II folder, ELP Link II icon
appears on the screen.Double-click the icon, then the main
ELP Link II window will appear.
If the ELP Link II window is hidden behind another window,
select ELP Link II from the application menu.
This will bring the ELP Link II window to the front.
¥To exit ELP Link II
Click the close button or select [End] from the Menu to exit the
application.
If the projectorÕs setting screen is open, you cannot exit ELP Link II.
First close the setting screen, then exit ELP Link II.