Epson Projector Emp 5100 User Manual

							3
All of the above items may not be required for your particular
computer system
uWarning: Keep the plastic bags for the projector, accessories and
optional parts out of the reach of small children. A plastic bag over
the head of a small child can result in death by suffocation.
Save all packaging materials in case you need to ship the projector in
the future. It should always be transported in its original packaging or
the equivalent.
Additional Items
The following items may also be required, depending upon how you
plan to use the projector.
¥S-Video cable for S-Video signal input
A separate cable is required for each video source.
¥Macintosh PowerBook output cable
This cable is normally provided with PowerBook models with video
output capabilities. Contact your Macintosh dealer if you need to
purchase one.
Unpacking the Projector 
						

							41 ¥ Installation
¥Special connector, cable or components for connecting the mouse
cable to your computer
These items should be available from your computer dealer. Note
that the mouse cable cannot be used with a computer that does not
have a mouse connector.
uNote: The hole on the right side of the projector accepts the connection
of the Kensington MicroSaver anti-theft device, which can be
pur chased at your local computer dealer. 
						

							5Setting Up the Projector
Setting Up the Projector
1. Place the projector on a stur dy, level surface within five feet of the
computer or video source.
2. Place the projector the correct distance from the screen.
The distance between the projector and the screen deter mines the
actual image size. Use the general guidelines below to determine
the correct distance.
Screen size
300 inches (610x460cm) 10.0 m (393.7 inches)
200 inches (410x300cm) 6.7 m (263.8 inches) ~ 8.7 m (342.5 inches)
100 inches (200x150cm) 3.3 m (129.9 inches) ~ 4.3 m (169.3 inches)
80 inches (160x120cm) 2.7 m (106.3 inches) ~ 3.5 m (137.8 inches)
60 inches (120x90cm) 2.0 m (78.7 inches) ~ 2.6 m (102.4 inches)
40 inches (81x61cm) 1.3 m (51.2 inches) ~ 1.7 m (66.9 inches)
30 inches (61x46cm) 1.0 m (39.4 inches) ~ 1.3 m (51.2 inches)
23 inches (47x35cm) 1.0 m (39.4 inches)
3. Turn the projector so that the lens is at right angles to the screen.
If the projector is not angled correctly the screen image will be
crooked.
Horizontal distance from the
projector to the screen 
						

							61 ¥ Installation
4. Connect one end of the power cable to the projectorÕs power
connector. Connect the other end to an earthed electrical socket.
The projector should be in sleep mode, indicated by an orange
power indicator.
uWarning: Never look into the lens when the pr ojector is on. There is a
risk that the projector might come on suddenly even though it is not
in use. The light from the lamp can damage your eyes. It is especially
important that children should not be allowed to look into the lens.
5. To insert the batteries in the remote control device, slide off the
batter y compartment cover as shown below.
6. Insert the two AA batteries included with the projector. Make
sure the polarity of the batteries is correct.
7. Replace the batter y compartment cover. 
						

							7
When replacing batteries, take the following precautions:
¥Do not mix old and new batteries.
¥Do not recharge used batteries or expose batteries to fire or water.
¥Replace batteries as soon as they run out. If the batteries leak,
wipe away the fluid with a soft cloth. If batter y fluid gets onto
your hands wash them immediately.
¥Remove the batteries if you will not be using the projector for a
long period.
Connecting to a Computer
You can connect the projector to a computer capable of SVGA, VGA,
SXGA and XGA (EMP-7100), SVGA, VGA and XGA (EMP-5100)
output. Resizing is supported for VGA, SVGA and SXGA (EMP-7100),
VGA and XGA (EMP-5100) output. Below a list may be found of the
types of computers supported by this projector.
¥IBM desktop PC or compatible
¥IBM laptop or compatible
¥Apple Macintosh desktop computer, including Macintosh
Quadra¨, Macintosh Centris¨, and Power Macintosh
¥Any Apple PowerBook with video-out capability, including all
160, 165, 180 and 500 series PowerBooks
Connecting to a Computer 
						

							81 ¥ Installation
Connecting to a PC desktop computer
Before beginning, make sure that the projector and computer are both
turned of f.
1. Connect either end of the computer cable to the projectorÕs
Computer In 1 port. The Computer In 2 por t is used when
connecting a second computer.
2. Disconnect the computerÕs monitor cable from the computerÕs
monitor port and connect the other end of the computer cable to
this port.
3. If necessary, connect the monitor cable of the computer monitor
to the projectorÕs Monitor port.
4. Connect the small end of the main cable to the projectorÕs
Mouse/Com 1 port. The Mouse/Com 2 port is used when you
are connecting a second computer.
5. Connect the PS/2 mouse cable  (9-pin) to the mouse terminal
on the large end of the main cable.
6. Disconnect the computerÕs mouse cable from the mouse port on
the back of your computer and connect the mouse connector
(6-pin) of the PS/2 mouse cable to the mouse port.
7. If you are planning to use the ELP Link II software, connect
either end of a PC serial cable to the PC SERIAL terminal on the
large end of the main cable.
8. Connect the other end of the PC serial cable to the serial port on
the back of your computer.
9. Tighten all connector screws to ensure secure connections.
¥ Note that you will not be able to use the ELP Link II software
if your system does not have two serial ports. 
						

							9Connecting to a Computer
¥If your system uses a serial mouse, perfor m steps 6 and 7
using the serial mouse cable instead of the PS/2 mouse cable.
    
Computer In 1 Computer In 2
Monitor
Audio In 1 Audio In 2 Audio Out
S-Video
Video InAudio In
LR
Remote
1-Mouse/ Com-2
Connecting to a PC laptop computer
Before beginning, make sure that the projector and computer are
both turned of f.
1. Connect either end of the computer cable to the projectors
Computer In 1 port. The Computer In 2 por t is used when
connecting a second computer.
2. Connect the other end of the computer cable to the laptopÕs
video (monitor) port.
3. If you wish to view or check images on the computerÕs monitor,
connect the cable that came with the monitor to the projectorÕs
monitor port.
4. Connect the small end of the main cable to the projectorÕs
Mouse/Com 1 port. The Mouse/Com 2 port is used when you
are connecting a second computer.
5. Connect the PS/2 mouse cable (9-pin) to the mouse terminal on
the large end of the main cable.
Main cableAudio cableMonitor cable
Computer cable
PC serial
cable
Serial mouse
cable
PS/2 mouse
cable
PS/2 mouse
cable
Mouse port
Serial portMonitor port
Audio port Com port 
						

							101 ¥ Installation
6.Disconnect the computerÕs mouse cable from the mouse port on the
back of the computer and connect the mouse connector of the PS/2
mouse cable (6-pin) to the mouse port on the back of your laptop.
¥ If your system uses a serial mouse, perform steps 6 and 7
using the serial mouse cable instead of the PS/2 mouse cable.
7. If you are planning to use the ELP Link II software, connect
either end of a PC serial cable to the PC SERIAL terminal on the
large end of the main cable.
8. Connect the other end of the PC serial cable to the serial port on
the back of your laptop.
9. Tighten all connector screws to ensure secure connections.
¥ Note that you will not be able to use the ELP Link II software
if your system does not have two serial ports.
 
Computer In 1 Computer In 2
Monitor
Audio In 1 Audio In 2 Audio Out
S-Video
Video InAudio In
LR
Remote
1-Mouse/ Com-2
PC serial
cablePS/2 mouse
cable
PS/2 mouse
cable
Serial mouse
cable
Monitor cable
Audio cableMain cable Monitor port
Mouse portCom port
Audio port
Serial port 
						

							11
Connecting to a Macintosh desktop computer
Before beginning, make sure that the projector and computer are
both turned of f.
1. Set the DIP switches of the MAC desktop adapter in accordance
with the resolutions you want to use (i.e. 16Ó mode).
2. Disconnect the monitor cable from the computer and connect it
to the large terminal (D-sub 15 pin) of the desktop adapter.
3. Tighten fixed screws for the desktop adapter.
4. Connect either end of the computer cable to the small terminal of
the desktop adapter.
5. Connect either end of the computer cable to the projectorÕs
Computer In 1 port. The Computer In 2 por t is used when
connecting a second computer.
6. If necessary, attach the MAC monitor adapter to the monitor
cable and connect the cable with the adapter to the projectorÕs
Monitor por t.
7. Connect the small end of the main cable to the projectorÕs
Mouse/Com 1 port. The Mouse/Com 2 port is used when you
are connecting a second computer.
8. Connect the MAC mouse cable (9-pin) to the mouse terminal on
the other end of the main cable.
9. Disconnect the mouse cable from the MAC port of the Macin-
tosh and connect the mouse connector of the MAC mouse cable
to the computerÕs MAC port.
10. If you are planning to use the ELP Link II software, connect
either end of a MAC serial cable to the MAC SERIAL terminal at
the large end of the main cable.
Connecting to a Computer 
						

							121 ¥ Installation
11. Connect the other end of the MAC serial cable to the printer
port or modem port on the back of your Macintosh.
12. Tighten all connector screws to ensure secure connections.
Computer In 1 Computer In 2
Monitor
Audio In 1 Audio In 2 Audio Out
S-Video
Video InAudio In
LR
Remote
1-Mouse/ Com-2
Connecting to a Macintosh PowerBook
Remember that you can only use a PowerBook model that have
video-out capability. See page 7 for more information.
Before beginning, make sure that the projector and PowerBook are
both turned of f.
1. Set the DIP switches of the MAC desktop adapter in accordance
with the resolutions you want to use (i.e. 16Ó mode).
2. Connect an adapter (which came with the computer or your
own) such as a converter for a D-Sub 15 terminal to the video
output port of your PowerBook.
Main cableAudio cable
Computer cable
MAC mouse
cableMAC serial
cable
MAC
desktop
adapter
Video cable
adapter
Monitor port
Audio port
ADB port
Printer port or
modem port
MAC
monitor
adapter
Monitor cable