Epson Projector EH TW9300 User Manual

Basic Operations
30
Adjusting the position of the projected image (Lens Shift Adjustment)
If the projector cannot be installed directly in front of the screen, you can adjust the position of the image by
using lens shift.
a
Press the  button on the remote control three times.
Adjust Lens Shift is displayed on the screen.
b
Use the  buttons to adjust the position of the image.
You can move the image within the range indicated by the dotted line in the following figure.
c
Hold down the  but-
tons to return...

Basic Operations
31
Adjusting the Projector's Tilt
If the projected image is horizontally tilted (the left and right sides of the projected image are at different
heights) when the projector is setup on a table, adjust the front foot so that both sides are level with each other.
Correcting Keystone Distortion
You can use the  buttons on the control panel to correct keystone distortion.
Open the control panel cover at the side to operate the control panel. 
s  p.7
Press the 
 or  buttons to display...

Adjusting the Image
32
Adjusting the Image
Selecting the Projection Quality (Color Mode)
You can obtain the optimum image quality to suit your surroundings when projecting. The brightness of the
image varies depending on the mode selected.
a
Press the  button.
c
•You can make settings from the Configuration menu. s Image - Color Mode  p.77
•If you press the  button, you can also make settings from the Home screen. s  p.26
b
Select Color Mode.
Use the  buttons to select a mode, and then press the  button...

Adjusting the Image
33
Switching the Screen Between Full and Zoom (Aspect)
You can change the input signal's type, aspect ratio, and resolution to match the Aspect of the projected
image.
The available settings vary depending on the image signal currently being projected.
c
Note that using the aspect ratio function of the projector to reduce, enlarge, or split the projected
image for commercial purposes or for public viewing may infringe upon the rights of the copyright
holder of that image based on...

Adjusting the Image
34
Input Image Setting Name
Normal Full Zoom
Notes
Matches the vertical size of
the projection panel. The
aspect ratio differs de-
pending on the input im-
age.Uses the entire projection
panel. The aspect ratio dif-
fers depending on the in-
put resolution.Retains the aspect ratio of
the input signal, and
matches the horizontal
size of the projection pan-
el. The top and bottom of
the image may be trunca-
ted.
*The letterbox image used in this explanation is a 4:3 aspect ratio image...

Adjusting the Image
35
d
Press the  button to exit the
menu.
Adjusting Image Resolution (Image Enhancement)
You can adjust the resolution of the image using the Image Enhancement function.
The following content can be adjusted.
4K Enhancement4K Enhancement is a function that projects an image at a doubled res-
olution by diagonally shifting 1 pixel in increments of 0.5 pixels.
A high-resolution image signal is projected in fine detail.
Image Preset ModeSelect the settings prepared in advance as the...

Adjusting the Image
36
c
Use the  buttons to make
adjustments.
Press the  button to adjust another
item.
Press the 
 button to return the
adjustments to their default values.
d
Press the  button to exit the
menu.
Setting Auto Iris
By automatically setting the luminance according to the displayed image, you can enjoy deep and rich images.
You can select the luminance adjustment tracking for changes in brightness in the displayed image from
Normal to High Speed.
Press the  button to display menus in the...

Adjusting the Image
37
Adjusting the Color
Adjusting the Color Temp.
You can adjust the overall tint of the image. Make adjustments if the image is a little too blue or too red and
so on.
Press the  button to display menus in the following
order.
Image - Color Temp. - Color Temp.
Use the 
 buttons to make adjustments.
Blue tints grow stronger as the value is increased, and red
tints grow stronger as the value is reduced.
c
Press the  button to return the adjustments to their default values.
Adjusting the...

Adjusting the Image
38
a
Press the  button.
c
You can make settings from the
Configuration menu. 
s Image -
Advanced - RGBCMY  p.77
b
Use the  buttons to
select the color you want to adjust,
and then press the 
 button to
confirm the selection.
c
Use the  buttons to
select Hue, Saturation, or
Brightness.
d
Use the  buttons to make
adjustments.
Press the  button to adjust another
color.
Press the 
 button to return the
adjustments to their default values.
e
Press the  button to exit the
menu. 

Adjusting the Image
39
Adjusting the Gamma
You can adjust slight coloration differences that may occur due to the device being used when the image is
displayed.
You can set it by using one of the following three methods.
•Select and adjust the correction value
•Adjust while viewing the image
•Adjust using the gamma adjustment graph
c
When a 3D signal or HDR signal is being input, you cannot select Adjust it from the image.
Select and adjust the correction value
a
Press the  button to display
menus in the...