Epson Projector EH-TW5350 User Manual
Have a look at the manual Epson Projector EH-TW5350 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Troubleshooting 80 Check Remedy Are the indicators switched off? Disconnect and then reconnect the projector's power cord. Check that pressing the power button after connection supplies the projector with power. Is an image signal being input? Check that the connected device is turned on. When Messag‐ es is set to On from the Configuration menu, image signal mes- sages are displayed. s Extended - Display - Messages p.70 Are the Configuration menu settings correct? Reset all of the settings. s Reset - Reset All p.74 (Only when projecting computer image sig- nals) Was the connection made while the power of the projector or the computer was already turned on?If the connection is made while the power is already turned on, the Fn key (Function key) that changes the computer's image signal to external output may not work. Turn off the power for the computer and the projector and then turn it back on again. Moving images are not displayed Check Remedy (Only when projecting computer image sig- nals) Is the computer's image signal set to external output and to output to the LCD monitor at the same time?Depending on the computer's specifications, moving images may not be displayed when the computer is set to external out- put and to the LCD monitor output at the same time. Change it so that the image signal is set to external output only. For the computer's specifications, see the documentation sup- plied with the computer. "Not supported" is displayed Check Remedy (Only when projecting computer image sig- nals) Do the image signal's frequency and resolu- tion correspond to the mode?Check the image signal being input in Resolution from the Con- figuration menu, and check that it corresponds to the projector's resolution. s About - Projector Info p.74 s p.96 "No Signal" is displayed Check Remedy Are the cables connected correctly?Check that all the cables required for projection are securely connected. s p.19 Is the correct image input port selected? Change the image with the source buttons on the remote con- trol, or the button on the control panel. s p.26 Is the connected device turned on? Turn on the device.
Troubleshooting 81 Check Remedy (Only when projecting computer image sig- nals) Are the image signals being output to the projector?Change it so that the image signal is set to external output, and not just the computer's LCD monitor. For some models, when the image signals are output externally, they no longer appear on the LCD monitor. For the computer's specifications, see the documentation sup- plied with the computer. If the connection is made while the power of the projector or the computer is already turned on, the Fn key (Function key) that changes the computer's image signal to external output may not work. Turn the power for the computer and the projector off and then back on again. Images are fuzzy or out of focus Check Remedy Has the focus been adjusted? Adjust the focus. s p.29 Is the lens cover closed? Open the lens cover. s p.26 Is the projector at the correct distance? Check the recommended projection range. s p.17 Has condensation formed on the lens? If the projector is suddenly taken from a cold environment to a warm environment, or if sudden ambient temperature changes occur, condensation may form on the surface of the lens, and this may cause the images to appear fuzzy. Set the projector up in the room about one hour before it is used. If the projector is wet from condensation, turn off the projector, disconnect the power cord, and leave it for a while. Interference or distortion appear in images Check Remedy Are the cables connected correctly?Check that all the cables required for projection are securely connected. s p.19 Is an extension cable being used? If an extension cable is used, electrical interference may affect the signals. (Only when projecting computer image sig- nals) Are the Sync. and Tracking settings adjusted correctly?The projector uses automatic adjustment functions to project at the optimum status. However, depending on the signal, some may not be adjusted correctly even after performing self correc- tions. If this happens, adjust the Tracking and Sync. settings from the Configuration menu. s Signal - Tracking/Sync. p.66 (Only when projecting computer image sig- nals) Is the correct resolution selected?Set the computer so that the signals being output are compatible with the projector. s p.96 Part of the image is truncated (large) or small Check Remedy Is the correct Aspect selected? Select the aspect mode to match the input signal in Aspect from the Configuration menu. s Signal - Aspect p.66
Troubleshooting 82 Check Remedy Is the image Position adjusted correctly? Adjust the Position setting from the Configuration menu. s Signal - Position p.66 (Only when projecting computer image sig- nals) Is the correct resolution selected?Set the computer so that the signals being output are compatible with the projector. s p.96 Image colors are not right Check Remedy Are the cables connected correctly?Check that all the cables required for projection are securely connected. s p.19 For the Video and PC ports, make sure the connector is the same color as the cable port. s p.19 Is the contrast adjusted correctly? Adjust the Contrast setting from the Configuration menu. s Image - Contrast p.65 Is the color adjusted correctly? Adjust the Advanced setting from the Configuration menu. s Image - Advanced p.65 (Only when projecting images from a video device) Are the color saturation and tint adjusted cor- rectly?Adjust the Color Saturation and Tint settings from the Config- uration menu. s Image - Color Saturation/Tint p.65 Images appear dark Check Remedy Is the image brightness set correctly? Adjust the Brightness setting from the Configuration menu. s Image - Brightness p.65 Is the contrast adjusted correctly? Adjust the Contrast setting from the Configuration menu. s Image - Contrast p.65 Is it time to replace the lamp? When the lamp is nearly ready for replacement, the images be- come darker and the color quality becomes poorer. When this happens, replace the lamp with a new lamp. s p.92 Projection stops automatically Check Remedy Is Sleep Mode enabled?If the set time is exceeded and no signal is input, the lamp is automatically turned off and the projector enters standby mode. The projector returns from standby mode when you press the button on the remote control or the control panel. If you want to disable Sleep Mode, change the setting to Off. s Exten‐ ded - Operation - Sleep Mode p.70
Troubleshooting 83 Problems when projection starts The projector does not turn on Check Remedy Is the power turned on? Press the button on the remote control or the control panel. Is Child Lock set to On? When Child Lock is set to On from the Configuration menu, hold down the button on the control panel for approximately three seconds, or perform operations from the remote control. s Settings - Lock Setting - Child Lock p.68 Do the indicators turn on and off when the power cord is touched?Turn off the projector, and then disconnect and reconnect the projector's power cord. If the problem continues, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest projector information center. s Epson Projector Contact List Problems with the remote control The remote control does not respond Check Remedy Is the remote control light-emitting area pointing towards the remote receiver on the projector during operation?Point the remote control towards the remote receiver. Also, check the operating range. s p.25 Is the remote control too far from the projec- tor?Check the operating range. s p.25 Is direct sunlight or strong light from fluores- cent lamps shining onto the remote receiver?Set the projector up in a location where strong light does not shine onto the remote receiver. Are the batteries dead or have the batteries been inserted correctly?Make sure the batteries are inserted correctly or replace the bat- teries with new ones if necessary. s p.24 Problems with 3D Cannot project correctly in 3D Check Remedy Are the 3D Glasses turned on? Turn on the 3D Glasses. Is a 3D image being projected? If the projector is projecting a 2D image, or if an error occurs on the projector that prevents the 3D image from being projected, you cannot view 3D images even if you are wearing the 3D Glasses. Is the input image in 3D? Check that the input image is 3D compatible. Since most TV broadcasts do not contain a 3D format signal, 3D reception must be set manually.
Troubleshooting 84 Check Remedy Is 3D Display set to 2D?If 3D Display is set to 2D from the Configuration menu, the pro- jector does not automatically change to 3D even when a 3D im- age is input. Press the button, and then set 3D Display to 3D or Auto. s Signal - 3D Setup - 3D Display p.66 Is 3D Format set correctly? Unless the 3D format of the AV device and 3D Format of the projector are the same, part of the image may not be displayed. Check that the projector's 3D Format setting matches the 3D format setting for the AV device. s Signal - 3D Setup - 3D For‐ mat p.66 When changing the 3D Format, set 3D Display to Auto, and then press the button. Are you viewing within the reception range? If the distance between the projector and the 3D Glasses exceed 10 m, the connection may be lost. Move the 3D Glasses closer to the projector. Has pairing been performed correctly? See the User's Guide for the 3D Glasses to perform pairing. Are there any devices that cause radio wave interference in the vicinity?When using other devices at the same time with the frequency band (2.4 GHz) such as Bluetooth communication devices, wire- less LAN (IEEE802.11b/g), or microwave ovens, radio wave inter- ference may occur, the image may be interrupted, or communi- cation may not be possible. Do not use the projector near these devices. Problems with HDMI HDMI Link does not function Check Remedy Are you using a cable that meets the HDMI standards?Operations are not possible with cables that do not meet the HDMI standards. Does the connected device meet the HDMI CEC standards?If the connected device does not meet the HDMI CEC standards, it cannot be operated even if it is connected to the HDMI port. See the documentation and so on supplied with the connected device for more information. Also, press the button, and then check if the device is available under Device Connections. s p.49 Are the cables connected correctly? Check that all the cables required to use HDMI Link are securely connected. s p.48 Is the power for the amplifier or DVD recorder and so on turned on?Put each device in standby status. See the documentation and so on supplied with the connected device for more information. If you have connected a speaker and so on, set the connected equipment to PCM output. Was a new device connected, or was the con- nection changed?If the CEC function for a connected device needs to be set again, for example when a new device is connected or the connection is changed, you may need to restart the device. Are many multi-media players connected? Up to 3 multi-media players that meet the HDMI CEC standards can be connected at the same time.
Troubleshooting 85 The device name is not displayed under Device Connections Check Remedy Does the connected device meet the HDMI CEC standards?If the connected device does not meet the HDMI CEC standards, it is not displayed. See the documentation and so on supplied with the connected device for more information. Network problems Cannot access the network via wireless LAN Check Remedy Is Wireless LAN Power set to Off?Set Wireless LAN Power to On in the Configuration menu. If this is already set to On, set Wireless LAN Power to Off, and then set it to On again. s Network - Wireless LAN Power p.71 Is the passphrase correct? Note that the passphrase is case sensitive; upper case and lower case letters are treated as different characters. If you have for- gotten your passphrase, set a new one. s Network Settings - Security - Passphrase p.71 Have you checked the Event ID? Check the Event ID number and perform the following steps. s Info - Event ID p.74 s p.88 The image contains static during network projection Check Remedy Are there any obstacles between the access point and the connected device?Check for any obstacles between the access point, the mobile device, the computer, and the projector, and change their posi- tions to improve communication. Is the distance between the access point and the connected device too far?Make sure that the access point, the mobile device, the comput- er, and the projector are not too far apart. Move them closer to- gether and try to connect again. Are there any Bluetooth devices or micro- wave oven in the vicinity?If the wireless connection is slow or your projected image con- tains noise, check for interference from other equipment, such as a Bluetooth device or microwave. Move the interfering device farther away or expand your wireless bandwidth. Are too many devices connected? Reduce the number of connected devices if the connection speed declines. Cannot connect using Screen Mirroring Check Remedy Is Screen Mirroring set to Off?Set Screen Mirroring to On in the Configuration menu. If this is already set to On, set Screen Mirroring to Off, and then set it to On again. s Network - Screen Mirroring p.71 Is there a hyphen (-) in the display name? Change the Display Name so that it does not include "-" in the projector's Screen Mirroring Settings menu. If the Display Name includes "-", it may not be displayed correctly on your mo- bile device. s Network - Screen Mirroring Settings p.71
Troubleshooting 86 Check Remedy Is the Screen Mirroring indicator lit blue? Make sure the Screen Mirroring indicator turns blue and the Screen Mirroring standby screen is displayed. s p.77 Are other mobile devices already connected? Make sure no other mobile device is connected to the projector. Are the settings correct for the mobile device? Make sure the settings on the mobile device are correct. If the settings are correct, restart the mobile device. Are you trying to reconnect immediately after the Screen Mirroring connection has ended?When connecting again immediately after disconnecting, it may take some time until the connection is established. Reconnect after waiting for a while. Are you connecting from the connection his- tory of the mobile device?Once you have connected using Screen Mirroring, the projector connection information may be recorded on the mobile device. However, you may not be able to reconnect to the projector from the recorded information. Select the projector from the list of available devices. Is wireless LAN with a 5 GHz bandwidth being used by devices with Intel WiDi?If your mobile device supports Intel WiDi and uses 5 GHz Wireless LAN, you cannot connect using Screen Mirroring and Wireless LAN at the same time. Turn off the Wireless LAN and connect using Screen Mirroring. The image contains static during Screen Mirroring connection Check Remedy Is the Wi-Fi antenna of the mobile device cov- ered?Try not to cover the Wi-Fi antenna of the mobile device. Is the mobile device connected to the inter- net?If you use a Screen Mirroring connection and an internet con- nection at the same time, the image may stop or contain noise. Disconnect the internet connection to expand your wireless bandwidth and improve the connection speed of the mobile device. Is there a problem in the projected content? Content that can be projected in Screen Mirroring is subject to restrictions. Make sure the projected content meets the require- ments. s p.59 Does the mobile device have a power saving setting?Depending on the settings of the mobile device, the connection may be lost when the device enters the power saving mode. Check the electrical power saving settings on the mobile device. Is the mobile device using the latest version of its wireless driver or firmware?Update to the latest version of the wireless driver or firmware on the mobile device. Bluetooth device problems c Bluetooth audio devices are not supported in some countries and regions.
Troubleshooting 87 Cannot Connect Bluetooth Device Check Remedy Was a device search performed? When connecting a Bluetooth device for the first time, or when changing to another Bluetooth device, perform Search Blue‐ tooth Device. s p.21 Does the device support copyright protection (SCMS-T)?You cannot connect a Bluetooth device that does not support copyright protection (SCMS-T). Is the device based on A2DP? You cannot connect a Bluetooth device that does not support A2DP. The audio and connection for the Bluetooth device disconnects Check Remedy Are there any obstacles between the projec- tor and the Bluetooth device?Check for any obstacles between the projector and the Bluetooth device, and change their positions to improve communication. Is the device connected within the specified communication distance?If the distance between the projector and the Bluetooth device exceed 10 m, the connection may be lost. Move the Bluetooth device closer to the projector. Are there any wireless equipment or micro- wave ovens in the vicinity?If the device is used at the same time as other wireless equipment or microwave ovens, radio wave interference may occur, and the image and audio may be interrupted. Avoid equipment that could cause interference. Other problems No audio, or the audio is too low Check Remedy Is the audio cable connected correctly? Try disconnecting the cable from the Audio (L-R) port, and then reconnecting. Is the volume too low? Adjust the volume so that you can hear the audio. s p.32 Is it connected with an HDMI cable? If no audio is output when connecting via an HDMI cable, set the connected equipment to PCM output. Are the Audio Out Device settings correct? Check that the Audio Out Device settings are correct on the Configuration menu. s Settings - HDMI Link - Audio Out De‐ vice p.68 Are the Bluetooth Audio settings correct? *Make the following settings when connecting a Bluetooth audio device. •To output audio from the projector's speaker or an AV system, set Bluetooth Audio to Off. •To output audio from Bluetooth audio devices, set Bluetooth Audio to On. s Settings - Bluetooth - Bluetooth Audio p.68 *Bluetooth audio devices are not supported in some countries and regions.
Troubleshooting 88 Cannot make settings on the control panel Check Remedy Is Control Panel Lock set to Full Lock or Par‐ tial Lock?When Control Panel Lock is set to Full Lock in the Configura- tion menu, all button operations on the control panel are disa- bled; when Partial Lock is set, only the button on the control panel is available. Perform operations from the remote control. s Settings - Lock Setting - Control Panel Lock p.68 Slideshow does not start Check Remedy Is the USB storage device using a security function?You may not be able to use USB storage devices that incorporate security functions. About Event ID Check the event ID and perform the remedy given below. If you cannot resolve the problem, contact your local dealer or the nearest Epson repair center. s Epson Projector Contact List Event ID Cause Remedy 0021 Failed to startup Screen Mirroring. Restart the projector. 0022 0027 0028 0029 0030 0031 0035 0434 0481 0482 0485Network communication is unstable. Check the network communication status, and reconnect after waiting for a while. 0023 0024 0025Connection failed. If you see the PIN entry screen on your com- puter, enter the PIN code displayed on the Screen Mirroring standby screen or at the bot- tom right of the projected image. If this does not solve the problem, restart the projector and the connected devices, and then check the connection settings. 0432 0435Failed to startup EasyMP Network Projection. Restart the projector. 0433 An image that was transferred cannot be re- produced.Restart EasyMP Network Projection. 0484 Communications was cut off from the comput- er. 0483 04FEEasyMP Network Projection ended unexpect- edly.Check the status of network communications. Wait for a while and then try connecting again.
Troubleshooting 89 Event ID Cause Remedy 0479 04FFA system error occurred in the projector. Restart the projector. 0891 The same SSID access point cannot be found. Set the computer, the access point, and the projector to the same SSID. 0892 WPA and WPA2 authentication type mismatch. Check the setting of wireless LAN security to see if it is correct. 0894 Communications was cut off because a con- nection was made to the wrong access point.Check with the network administrator and fol- low their instructions. 0898 Failed to acquire the DHCP. Check the DHCP server to see if it is operating correctly. Turn off DHCP if it is not being used. s Network Settings - Wireless LAN - IP Set‐ tings - DHCP p.71 0020 0026 0032 0036 0037 0038 0899Other connection errors If restarting the projector or network applica- tions does not solve the problem, contact one of the following addresses. s Epson Projector Contact List